A distinguished network ID that will never be assigned to any node. This value is returned when getting the remote node ID from the binding table and the given binding table index refers to a multicast binding entry.

#define

EMBER_UNKNOWN_NODE_ID 0xFFFDu

A distinguished network ID that will never be assigned to any node. This value is used when getting the remote node ID from the address or binding tables. It indicates that the address or binding table entry is currently in use but the node ID corresponding to the EUI64 in the table is currently unknown.

#define

EMBER_DISCOVERY_ACTIVE_NODE_ID 0xFFFCu

#define

EMBER_NULL_ADDRESS_TABLE_INDEX 0xFFu

A distinguished address table index used to indicate the absence of an address table entry.

#define

EMBER_ZDO_ENDPOINT 0u

The endpoint where the ZigBee Device Object (ZDO) resides.

#define

EMBER_BROADCAST_ENDPOINT 0xFFu

The broadcast endpoint, as defined in the ZigBee spec.

#define

EMBER_ZDO_PROFILE_ID 0x0000u

The profile ID used by the ZigBee Device Object (ZDO).

#define

EMBER_WILDCARD_PROFILE_ID 0xFFFFu

The profile ID used to address all the public profiles.

#define

EMBER_MAXIMUM_STANDARD_PROFILE_ID 0x7FFFu

The maximum value for a profile ID in the standard profile range.

#define

EMBER_BROADCAST_TABLE_TIMEOUT_QS (20 * 4)

The broadcast table entry timeout, which specifies, in quarter seconds, how long an entry persists in the local device's broadcast table.

#define

EMBER_MANUFACTURER_ID 0x1002u

Ember's Manufacturer ID.

#define

EMBER_NULL_NETWORK_INDEX 0xFFu

An invalid network index.

#define

EMBER_DC_LIMIT_USE_DEFAULT 0

Use Ember's default duty cycle limit configurations.

ZigBee Broadcast Addresses#

ZigBee specifies three different broadcast addresses that reach different collections of nodes. Broadcasts are normally sent only to routers. Broadcasts can also be forwarded to end devices, either all of them or only those that do not sleep. Broadcasting to end devices is both significantly more resource-intensive and significantly less reliable than broadcasting to routers.

#define

EMBER_BROADCAST_ADDRESS 0xFFFCu

#define

EMBER_RX_ON_WHEN_IDLE_BROADCAST_ADDRESS 0xFFFDu

#define

EMBER_SLEEPY_BROADCAST_ADDRESS 0xFFFFu

Ember Concentrator Types#

enum

EmberAssumeTrustCenterConcentratorType {

EMBER_ASSUME_TRUST_CENTER_IS_NOT_A_CONCENTRATOR = 0

EMBER_ASSUME_TRUST_CENTER_IS_LOW_RAM_CONCENTRATOR = 1

EMBER_ASSUME_TRUST_CENTER_IS_HIGH_RAM_CONCENTRATOR = 2

}

To configure non trust center node to assume a concentrator type of the trust center it join to, until it receive many-to-one route request from the trust center. For the trust center node, concentrator type is configured from the concentrator plugin. The stack by default assumes trust center be a low RAM concentrator that make other devices send route record to the trust center even without receiving a many-to-one route request. The assumed concentrator type can be changed by setting appropriate value to emberAssumedTrustCenterConcentratorType.

enum

EmberJoinDecision {

EMBER_USE_PRECONFIGURED_KEY = 0

EMBER_SEND_KEY_IN_THE_CLEAR

EMBER_DENY_JOIN

EMBER_NO_ACTION

EMBER_ALLOW_REJOINS_ONLY

}

The decision made by the Trust Center when a node attempts to join.

enum

EmberDeviceUpdate {

EMBER_STANDARD_SECURITY_SECURED_REJOIN = 0

EMBER_STANDARD_SECURITY_UNSECURED_JOIN = 1

EMBER_DEVICE_LEFT = 2

EMBER_STANDARD_SECURITY_UNSECURED_REJOIN = 3

}

The Status of the Update Device message sent to the Trust Center. The device may have joined or rejoined insecurely, rejoined securely, or left. MAC Security has been deprecated and therefore there is no secure join.

enum

EmberRejoinReason {

EMBER_REJOIN_REASON_NONE = 0

EMBER_REJOIN_DUE_TO_NWK_KEY_UPDATE = 1

EMBER_REJOIN_DUE_TO_LEAVE_MESSAGE = 2

EMBER_REJOIN_DUE_TO_NO_PARENT = 3

EMBER_REJOIN_DUE_TO_ZLL_TOUCHLINK = 4

EMBER_REJOIN_DUE_TO_END_DEVICE_REBOOT = 5

EMBER_REJOIN_DUE_TO_APP_EVENT_5 = 0xFB

EMBER_REJOIN_DUE_TO_APP_EVENT_4 = 0xFC

EMBER_REJOIN_DUE_TO_APP_EVENT_3 = 0xFD

EMBER_REJOIN_DUE_TO_APP_EVENT_2 = 0xFE

EMBER_REJOIN_DUE_TO_APP_EVENT_1 = 0xFF

}

Notes the last rejoin reason.

enum

EmberClusterListId {

EMBER_INPUT_CLUSTER_LIST = 0

EMBER_OUTPUT_CLUSTER_LIST = 1

}

Defines the lists of clusters that must be provided for each endpoint.

enum

EmberEventUnits {

EMBER_EVENT_INACTIVE = 0

EMBER_EVENT_MS_TIME

EMBER_EVENT_QS_TIME

EMBER_EVENT_MINUTE_TIME

EMBER_EVENT_ZERO_DELAY

}

Either marks an event as inactive or specifies the units for the event execution time.

enum

EmberJoinMethod {

EMBER_USE_MAC_ASSOCIATION = 0

EMBER_USE_NWK_REJOIN = 1

EMBER_USE_NWK_REJOIN_HAVE_NWK_KEY = 2

EMBER_USE_CONFIGURED_NWK_STATE = 3

}

The type of method used for joining.

enum

EmberCounterType {

EMBER_COUNTER_MAC_RX_BROADCAST = 0

EMBER_COUNTER_MAC_TX_BROADCAST = 1

EMBER_COUNTER_MAC_RX_UNICAST = 2

EMBER_COUNTER_MAC_TX_UNICAST_SUCCESS = 3

EMBER_COUNTER_MAC_TX_UNICAST_RETRY = 4

EMBER_COUNTER_MAC_TX_UNICAST_FAILED = 5

EMBER_COUNTER_APS_DATA_RX_BROADCAST = 6

EMBER_COUNTER_APS_DATA_TX_BROADCAST = 7

EMBER_COUNTER_APS_DATA_RX_UNICAST = 8

EMBER_COUNTER_APS_DATA_TX_UNICAST_SUCCESS = 9

EMBER_COUNTER_APS_DATA_TX_UNICAST_RETRY = 10

EMBER_COUNTER_APS_DATA_TX_UNICAST_FAILED = 11

EMBER_COUNTER_ROUTE_DISCOVERY_INITIATED = 12

EMBER_COUNTER_NEIGHBOR_ADDED = 13

EMBER_COUNTER_NEIGHBOR_REMOVED = 14

EMBER_COUNTER_NEIGHBOR_STALE = 15

EMBER_COUNTER_JOIN_INDICATION = 16

EMBER_COUNTER_CHILD_REMOVED = 17

EMBER_COUNTER_ASH_OVERFLOW_ERROR = 18

EMBER_COUNTER_ASH_FRAMING_ERROR = 19

EMBER_COUNTER_ASH_OVERRUN_ERROR = 20

EMBER_COUNTER_NWK_FRAME_COUNTER_FAILURE = 21

EMBER_COUNTER_APS_FRAME_COUNTER_FAILURE = 22

EMBER_COUNTER_ASH_XOFF = 23

EMBER_COUNTER_APS_LINK_KEY_NOT_AUTHORIZED = 24

EMBER_COUNTER_NWK_DECRYPTION_FAILURE = 25

EMBER_COUNTER_APS_DECRYPTION_FAILURE = 26

EMBER_COUNTER_ALLOCATE_PACKET_BUFFER_FAILURE = 27

EMBER_COUNTER_RELAYED_UNICAST = 28

EMBER_COUNTER_PHY_TO_MAC_QUEUE_LIMIT_REACHED = 29

EMBER_COUNTER_PACKET_VALIDATE_LIBRARY_DROPPED_COUNT = 30

EMBER_COUNTER_TYPE_NWK_RETRY_OVERFLOW = 31

EMBER_COUNTER_PHY_CCA_FAIL_COUNT = 32

EMBER_COUNTER_BROADCAST_TABLE_FULL = 33

EMBER_COUNTER_PTA_LO_PRI_REQUESTED = 34

EMBER_COUNTER_PTA_HI_PRI_REQUESTED = 35

EMBER_COUNTER_PTA_LO_PRI_DENIED = 36

EMBER_COUNTER_PTA_HI_PRI_DENIED = 37

EMBER_COUNTER_PTA_LO_PRI_TX_ABORTED = 38

EMBER_COUNTER_PTA_HI_PRI_TX_ABORTED = 39

EMBER_COUNTER_ADDRESS_CONFLICT_SENT = 40

EMBER_COUNTER_TYPE_COUNT = 41

}

Defines the events reported to the application by the emberCounterHandler().

typedef uint8_t

EmberTaskId

#define

EMBER_LOW_RAM_CONCENTRATOR 0xFFF8u

#define

EMBER_HIGH_RAM_CONCENTRATOR 0xFFF9u

#define

EMBER_JOIN_DECISION_STRINGS undefined

#define

EMBER_DEVICE_UPDATE_STRINGS undefined

#define

emberInitializeNetworkParameters (parameters)

#define

EMBER_COUNTER_STRINGS

txPowerModes for emberSetTxPowerMode and mfglibSetPower#

#define

EMBER_TX_POWER_MODE_DEFAULT 0x0000

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to disable all power mode options, resulting in normal power mode and bi-directional RF transmitter output.

#define

EMBER_TX_POWER_MODE_BOOST 0x0001

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable boost power mode.

#define

EMBER_TX_POWER_MODE_ALTERNATE 0x0002

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable the alternate transmitter output.

#define

EMBER_TX_POWER_MODE_BOOST_AND_ALTERNATE undefined

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable both boost mode and the alternate transmitter output.

Counters Request Definitions#

enum

EmberInitialSecurityBitmask {

EMBER_DISTRIBUTED_TRUST_CENTER_MODE = 0x0002

EMBER_TRUST_CENTER_GLOBAL_LINK_KEY = 0x0004

EMBER_PRECONFIGURED_NETWORK_KEY_MODE = 0x0008

EMBER_HAVE_TRUST_CENTER_EUI64 = 0x0040

EMBER_TRUST_CENTER_USES_HASHED_LINK_KEY = 0x0084

EMBER_HAVE_PRECONFIGURED_KEY = 0x0100

EMBER_HAVE_NETWORK_KEY = 0x0200

EMBER_GET_LINK_KEY_WHEN_JOINING = 0x0400

EMBER_REQUIRE_ENCRYPTED_KEY = 0x0800

EMBER_NO_FRAME_COUNTER_RESET = 0x1000

EMBER_GET_PRECONFIGURED_KEY_FROM_INSTALL_CODE = 0x2000

}

This is the Initial Security Bitmask that controls the use of various security features.

enum

EmberExtendedSecurityBitmask {

EMBER_SECURE_NETWORK_KEY_ROTATION = 0x0002

EMBER_JOINER_GLOBAL_LINK_KEY = 0x0010

EMBER_EXT_NO_FRAME_COUNTER_RESET = 0x0020

EMBER_NWK_LEAVE_WITHOUT_REJOIN_NOT_ALLOWED = 0x0040

EMBER_NWK_LEAVE_REQUEST_NOT_ALLOWED = 0x0100

}

This is the Extended Security Bitmask that controls the use of various extended security features.

enum

EmberCurrentSecurityBitmask {

EMBER_STANDARD_SECURITY_MODE_ = 0x0000

EMBER_DISTRIBUTED_TRUST_CENTER_MODE_ = 0x0002

EMBER_TRUST_CENTER_GLOBAL_LINK_KEY_ = 0x0004

EMBER_HAVE_TRUST_CENTER_LINK_KEY = 0x0010

EMBER_TRUST_CENTER_USES_HASHED_LINK_KEY_ = 0x0084

}

This is the Current Security Bitmask that details the use of various security features.

enum

EmberKeyStructBitmask {

EMBER_KEY_HAS_SEQUENCE_NUMBER = 0x0001

EMBER_KEY_HAS_OUTGOING_FRAME_COUNTER = 0x0002

EMBER_KEY_HAS_INCOMING_FRAME_COUNTER = 0x0004

EMBER_KEY_HAS_PARTNER_EUI64 = 0x0008

EMBER_KEY_IS_AUTHORIZED = 0x0010

EMBER_KEY_PARTNER_IS_SLEEPY = 0x0020

EMBER_UNCONFIRMED_TRANSIENT_KEY = 0x0040

}

This bitmask describes the presence of fields within the EmberKeyStruct.

enum

EmberKeyType {

EMBER_TRUST_CENTER_LINK_KEY = 1

EMBER_CURRENT_NETWORK_KEY = 3

EMBER_NEXT_NETWORK_KEY = 4

EMBER_APPLICATION_LINK_KEY = 5

}

This denotes the type of security key.

enum

EmberKeyStatus {

EMBER_KEY_STATUS_NONE = 0x00

EMBER_APP_LINK_KEY_ESTABLISHED = 0x01

EMBER_TRUST_CENTER_LINK_KEY_ESTABLISHED = 0x03

EMBER_KEY_ESTABLISHMENT_TIMEOUT = 0x04

EMBER_KEY_TABLE_FULL = 0x05

EMBER_TC_RESPONDED_TO_KEY_REQUEST = 0x06

EMBER_TC_APP_KEY_SENT_TO_REQUESTER = 0x07

EMBER_TC_RESPONSE_TO_KEY_REQUEST_FAILED = 0x08

EMBER_TC_REQUEST_KEY_TYPE_NOT_SUPPORTED = 0x09

EMBER_TC_NO_LINK_KEY_FOR_REQUESTER = 0x0A

EMBER_TC_REQUESTER_EUI64_UNKNOWN = 0x0B

EMBER_TC_RECEIVED_FIRST_APP_KEY_REQUEST = 0x0C

EMBER_TC_TIMEOUT_WAITING_FOR_SECOND_APP_KEY_REQUEST = 0x0D

EMBER_TC_NON_MATCHING_APP_KEY_REQUEST_RECEIVED = 0x0E

EMBER_TC_FAILED_TO_SEND_APP_KEYS = 0x0F

EMBER_TC_FAILED_TO_STORE_APP_KEY_REQUEST = 0x10

EMBER_TC_REJECTED_APP_KEY_REQUEST = 0x11

EMBER_TC_FAILED_TO_GENERATE_NEW_KEY = 0x12

EMBER_TC_FAILED_TO_SEND_TC_KEY = 0x13

EMBER_TRUST_CENTER_IS_PRE_R21 = 0x1E

EMBER_TC_REQUESTER_VERIFY_KEY_TIMEOUT = 0x32

EMBER_TC_REQUESTER_VERIFY_KEY_FAILURE = 0x33

EMBER_TC_REQUESTER_VERIFY_KEY_SUCCESS = 0x34

EMBER_VERIFY_LINK_KEY_FAILURE = 0x64

EMBER_VERIFY_LINK_KEY_SUCCESS = 0x65

}

This denotes the status of an attempt to establish a key with another device.

enum

EmberTcLinkKeyRequestPolicy {

EMBER_DENY_TC_LINK_KEY_REQUESTS = 0x00

EMBER_ALLOW_TC_LINK_KEY_REQUEST_AND_SEND_CURRENT_KEY = 0x01

EMBER_ALLOW_TC_LINK_KEY_REQUEST_AND_GENERATE_NEW_KEY = 0x02

}

This enumeration determines whether or not a Trust Center answers trust center link key requests.

enum

EmberAppLinkKeyRequestPolicy {

EMBER_DENY_APP_LINK_KEY_REQUESTS = 0x00

EMBER_ALLOW_APP_LINK_KEY_REQUEST = 0x01

}

This enumeration determines whether or not a Trust Center answers app link key requests.

enum

EmberKeySettings {

EMBER_KEY_PERMISSIONS_NONE = 0x0000

EMBER_KEY_PERMISSIONS_READING_ALLOWED = 0x0001

EMBER_KEY_PERMISSIONS_HASHING_ALLOWED = 0x0002

}

This is a ZigBee application profile ID that has been assigned to Ember Corporation.

enum

EmberMacPassthroughType {

EMBER_MAC_PASSTHROUGH_NONE = 0x00

EMBER_MAC_PASSTHROUGH_SE_INTERPAN = 0x01

EMBER_MAC_PASSTHROUGH_EMBERNET = 0x02

EMBER_MAC_PASSTHROUGH_EMBERNET_SOURCE = 0x04

EMBER_MAC_PASSTHROUGH_APPLICATION = 0x08

EMBER_MAC_PASSTHROUGH_CUSTOM = 0x10

}

The types of MAC passthrough messages that an application may receive. This is a bitmask.

uint8_t *

emberKeyContents(EmberKeyData *key)

This function allows access to the actual key data bytes of the EmberKeyData structure.

uint8_t *

emberCertificateContents(EmberCertificateData *cert)

This function allows access to the actual certificate data bytes of the EmberCertificateData structure.

uint8_t *

emberPublicKeyContents(EmberPublicKeyData *key)

This function allows access to the actual public key data bytes of the EmberPublicKeyData structure.

uint8_t *

emberPrivateKeyContents(EmberPrivateKeyData *key)

This function allows access to the actual private key data bytes of the EmberPrivateKeyData structure.

uint8_t *

emberSmacContents(EmberSmacData *key)

This function allows access to the actual SMAC (Secured Message Authentication Code) data of the EmberSmacData structure.

uint8_t *

emberSignatureContents(EmberSignatureData *sig)

This function allows access to the actual ECDSA signature data of the EmberSignatureData structure.

uint8_t *

emberCertificate283k1Contents(EmberCertificate283k1Data *cert)

This function allows access to the actual certificate data bytes of the Ember283k1CertificateData structure.

uint8_t *

emberPublicKey283k1Contents(EmberPublicKey283k1Data *key)

This function allows access to the actual public key data bytes of the Ember283k1PublicKeyData structure.

uint8_t *

emberPrivateKey283k1Contents(EmberPrivateKey283k1Data *key)

This function allows access to the actual private key data bytes of the Ember283k1PrivateKeyData structure.

uint8_t *

ember283k1SignatureContents(Ember283k1SignatureData *sig)

This function allows access to the actual ECDSA signature data of the Ember283k1SignatureData structure.

#define

EMBER_PRIVATE_PROFILE_ID 0xC00Eu

This is a ZigBee application profile ID that has been assigned to Ember Corporation.

#define

EMBER_PRIVATE_PROFILE_ID_START 0xC00Du

Ember's first private profile ID.

#define

EMBER_PRIVATE_PROFILE_ID_END 0xC016u

Ember's last private profile ID.

#define

EMBER_REPORT_COUNTERS_REQUEST 0x0003u

#define

EMBER_REPORT_COUNTERS_RESPONSE 0x8003u

#define

EMBER_REPORT_AND_CLEAR_COUNTERS_REQUEST 0x0004u

#define

EMBER_REPORT_AND_CLEAR_COUNTERS_RESPONSE 0x8004u

#define

EMBER_OTA_CERTIFICATE_UPGRADE_CLUSTER 0x0005u

#define

EMBER_STANDARD_SECURITY_MODE 0x0000

This is an EmberInitialSecurityBitmask value but it does not actually set anything. It is the default mode used by the ZigBee Pro stack. It is defined here so that no legacy code is broken by referencing it.

#define

EMBER_TRUST_CENTER_NODE_ID 0x0000u

The short address of the trust center. This address never changes dynamically.

#define

EMBER_NO_TRUST_CENTER_MODE EMBER_DISTRIBUTED_TRUST_CENTER_MODE

This is the legacy name for the Distributed Trust Center Mode.

#define

EMBER_GLOBAL_LINK_KEY EMBER_TRUST_CENTER_GLOBAL_LINK_KEY

This is the legacy name for the Trust Center Global Link Key.

#define

EMBER_MFG_SECURITY_CONFIG_MAGIC_NUMBER 0xCABAD11FUL

This magic number prevents accidentally changing the key settings. The emberSetMfgSecurityConfig() API will return EMBER_INVALID_CALL unless it is passed in.

ZDO response status.#

Most responses to ZDO commands contain a status byte. The meaning of this byte is defined by the ZigBee Device Profile.

enum

EmberZdoStatus {

EMBER_ZDP_SUCCESS = 0x00

EMBER_ZDP_INVALID_REQUEST_TYPE = 0x80

EMBER_ZDP_DEVICE_NOT_FOUND = 0x81

EMBER_ZDP_INVALID_ENDPOINT = 0x82

EMBER_ZDP_NOT_ACTIVE = 0x83

EMBER_ZDP_NOT_SUPPORTED = 0x84

EMBER_ZDP_TIMEOUT = 0x85

EMBER_ZDP_NO_MATCH = 0x86

EMBER_ZDP_NO_ENTRY = 0x88

EMBER_ZDP_NO_DESCRIPTOR = 0x89

EMBER_ZDP_INSUFFICIENT_SPACE = 0x8a

EMBER_ZDP_NOT_PERMITTED = 0x8b

EMBER_ZDP_TABLE_FULL = 0x8c

EMBER_ZDP_NOT_AUTHORIZED = 0x8d

EMBER_ZDP_DEVICE_BINDING_TABLE_FULL = 0x8e

EMBER_ZDP_INVALID_INDEX = 0x8f

EMBER_NWK_ALREADY_PRESENT = 0xC5

EMBER_NWK_TABLE_FULL = 0xC7

EMBER_NWK_UNKNOWN_DEVICE = 0xC8

}

Network and IEEE Address Request/Response#

Defines for ZigBee device profile cluster IDs follow. These include descriptions of the formats of the messages.Note that each message starts with a 1-byte transaction sequence number. This sequence number is used to match a response command frame to the request frame that it is replying to. The application shall maintain a 1-byte counter that is copied into this field and incremented by one for each command sent. When a value of 0xff is reached, the next command shall re-start the counter with a value of 0x00.Network request: <transaction sequence number: 1> <EUI64:8> <type:1> <start index:1>IEEE request: <transaction sequence number: 1> <node ID:2> <type:1> <start index:1> <type> = 0x00 single address response, ignore the start index = 0x01 extended response -> sends kid's IDs as wellResponse: <transaction sequence number: 1> <status:1> <EUI64:8> <node ID:2> <ID count:1> <start index:1> <child ID:2>*

#define

NETWORK_ADDRESS_REQUEST 0x0000u

#define

NETWORK_ADDRESS_RESPONSE 0x8000u

#define

IEEE_ADDRESS_REQUEST 0x0001u

#define

IEEE_ADDRESS_RESPONSE 0x8001u

Node Descriptor Request/Response#

Request: <transaction sequence number: 1> <node ID:2> Response: <transaction sequence number: 1> <status:1> <node ID:2>// <node descriptor: 13>//// Node Descriptor field is divided into subfields of bitmasks as follows:// (Note: All lengths below are given in bits rather than bytes.)// Logical Type: 3// Complex Descriptor Available: 1// User Descriptor Available: 1// (reserved/unused): 3// APS Flags: 3// Frequency Band: 5// MAC capability flags: 8// Manufacturer Code: 16// Maximum buffer size: 8// Maximum incoming transfer size: 16// Server mask: 16// Maximum outgoing transfer size: 16// Descriptor Capability Flags: 8// See ZigBee document 053474, Section 2.3.2.3 for more details.

#define

NODE_DESCRIPTOR_REQUEST 0x0002u

#define

NODE_DESCRIPTOR_RESPONSE 0x8002u

Power Descriptor Request / Response#

Request: <transaction sequence number: 1> <node ID:2> Response: <transaction sequence number: 1> <status:1> <node ID:2> <current power mode, available power sources:1> <current power source, current power source level:1>// See ZigBee document 053474, Section 2.3.2.4 for more details.

#define

POWER_DESCRIPTOR_REQUEST 0x0003u

#define

POWER_DESCRIPTOR_RESPONSE 0x8003u

Simple Descriptor Request / Response#

Request: <transaction sequence number: 1> <node ID:2> <endpoint:1>Response: <transaction sequence number: 1> <status:1> <node ID:2> <length:1> <endpoint:1> <app profile ID:2> <app device ID:2> <app device version, app flags:1> <input cluster count:1> <input cluster:2>* <output cluster count:1> <output cluster:2>*

#define

SIMPLE_DESCRIPTOR_REQUEST 0x0004u

#define

SIMPLE_DESCRIPTOR_RESPONSE 0x8004u

Active Endpoints Request / Response#

Request: <transaction sequence number: 1> <node ID:2>Response: <transaction sequence number: 1> <status:1> <node ID:2> <endpoint count:1> <endpoint:1>*

#define

ACTIVE_ENDPOINTS_REQUEST 0x0005u

#define

ACTIVE_ENDPOINTS_RESPONSE 0x8005u

Match Descriptors Request / Response#

Request: <transaction sequence number: 1> <node ID:2> <app profile ID:2> <input cluster count:1> <input cluster:2>* <output cluster count:1> <output cluster:2>*Response: <transaction sequence number: 1> <status:1> <node ID:2> <endpoint count:1> <endpoint:1>*

#define

MATCH_DESCRIPTORS_REQUEST 0x0006u

#define

MATCH_DESCRIPTORS_RESPONSE 0x8006u

Discovery Cache Request / Response#

Request: <transaction sequence number: 1> <source node ID:2> <source EUI64:8>Response: <transaction sequence number: 1> <status (== EMBER_ZDP_SUCCESS):1>

#define

DISCOVERY_CACHE_REQUEST 0x0012u

#define

DISCOVERY_CACHE_RESPONSE 0x8012u

End Device Announce and End Device Announce Response#

Request: <transaction sequence number: 1> <node ID:2> <EUI64:8> <capabilities:1>No response is sent.

#define

END_DEVICE_ANNOUNCE 0x0013u

#define

END_DEVICE_ANNOUNCE_RESPONSE 0x8013u

System Server Discovery Request / Response#

This is broadcast and only servers which have matching services respond. The response contains the request services that the recipient provides.Request: <transaction sequence number: 1> <server mask:2>Response: <transaction sequence number: 1> <status (== EMBER_ZDP_SUCCESS):1> <server mask:2>

#define

SYSTEM_SERVER_DISCOVERY_REQUEST 0x0015u

#define

SYSTEM_SERVER_DISCOVERY_RESPONSE 0x8015u

Parent Announce and Parent Announce Response#

This is broadcast and only servers which have matching children respond. The response contains the list of children that the recipient now holds.Request: <transaction sequence number: 1> <number of children:1> <child EUI64:8> <child Age:4>*Response: <transaction sequence number: 1> <number of children:1> <child EUI64:8> <child Age:4>*

#define

PARENT_ANNOUNCE 0x001Fu

#define

PARENT_ANNOUNCE_RESPONSE 0x801Fu

ZDO server mask bits#

These are used in server discovery requests and responses.

enum

EmberZdoServerMask {

EMBER_ZDP_PRIMARY_TRUST_CENTER = 0x0001

EMBER_ZDP_SECONDARY_TRUST_CENTER = 0x0002

EMBER_ZDP_PRIMARY_BINDING_TABLE_CACHE = 0x0004

EMBER_ZDP_SECONDARY_BINDING_TABLE_CACHE = 0x0008

EMBER_ZDP_PRIMARY_DISCOVERY_CACHE = 0x0010

EMBER_ZDP_SECONDARY_DISCOVERY_CACHE = 0x0020

EMBER_ZDP_NETWORK_MANAGER = 0x0040

}

Find Node Cache Request / Response#

This is broadcast and only discovery servers which have the information for the device of interest, or the device of interest itself, respond. The requesting device can then direct any service discovery requests to the responder.Request: <transaction sequence number: 1> <device of interest ID:2> <d-of-i EUI64:8>Response: <transaction sequence number: 1> <responder ID:2> <device of interest ID:2> <d-of-i EUI64:8>

#define

FIND_NODE_CACHE_REQUEST 0x001Cu

#define

FIND_NODE_CACHE_RESPONSE 0x801Cu

End Device Bind Request / Response#

Request: <transaction sequence number: 1> <node ID:2> <EUI64:8> <endpoint:1> <app profile ID:2> <input cluster count:1> <input cluster:2>* <output cluster count:1> <output cluster:2>*Response: <transaction sequence number: 1> <status:1>

#define

END_DEVICE_BIND_REQUEST 0x0020u

#define

END_DEVICE_BIND_RESPONSE 0x8020u

Binding types and Request / Response#

Bind and unbind have the same formats. There are two possible formats, depending on whether the destination is a group address or a device address. Device addresses include an endpoint, groups don't.Request: <transaction sequence number: 1> <source EUI64:8> <source endpoint:1> <cluster ID:2> <destination address:3 or 10>Destination address: <0x01:1> <destination group:2>Or: <0x03:1> <destination EUI64:8> <destination endpoint:1>Response: <transaction sequence number: 1> <status:1>

#define

UNICAST_BINDING 0x03u

#define

UNICAST_MANY_TO_ONE_BINDING 0x83u

#define

MULTICAST_BINDING 0x01u

#define

BIND_REQUEST 0x0021u

#define

BIND_RESPONSE 0x8021u

#define

UNBIND_REQUEST 0x0022u

#define

UNBIND_RESPONSE 0x8022u

LQI Table Request / Response#

Request: <transaction sequence number: 1> <start index:1>Response: <transaction sequence number: 1> <status:1> <neighbor table entries:1> <start index:1> <entry count:1> <entry:22>* <entry> = <extended PAN ID:8> <EUI64:8> <node ID:2> <device type, RX on when idle, relationship:1> <permit joining:1> <depth:1> <LQI:1>The device-type byte has the following fields: Name Mask Valuesdevice type 0x03 0x00 coordinator 0x01 router 0x02 end device 0x03 unknownrx mode 0x0C 0x00 off when idle 0x04 on when idle 0x08 unknownrelationship 0x70 0x00 parent 0x10 child 0x20 sibling 0x30 other 0x40 previous childreserved 0x10The permit-joining byte has the following fields Name Mask Valuespermit joining 0x03 0x00 not accepting join requests 0x01 accepting join requests 0x02 unknownreserved 0xFC

#define

LQI_TABLE_REQUEST 0x0031u

#define

LQI_TABLE_RESPONSE 0x8031u

Routing Table Request / Response#

Request: <transaction sequence number: 1> <start index:1>Response: <transaction sequence number: 1> <status:1> <routing table entries:1> <start index:1> <entry count:1> <entry:5>* <entry> = <destination address:2> <status:1> <next hop:2>The status byte has the following fields: Name Mask Valuesstatus 0x07 0x00 active 0x01 discovery underway 0x02 discovery failed 0x03 inactive 0x04 validation underwayflags 0x38 0x08 memory constrained 0x10 many-to-one 0x20 route record requiredreserved 0xC0

#define

ROUTING_TABLE_REQUEST 0x0032u

#define

ROUTING_TABLE_RESPONSE 0x8032u

Binding Table Request / Response#

Request: <transaction sequence number: 1> <start index:1>Response: <transaction sequence number: 1> <status:1> <binding table entries:1> <start index:1> <entry count:1> <entry:14/21>* <entry> = <source EUI64:8> <source endpoint:1> <cluster ID:2> <dest addr mode:1> <dest:2/8> <dest endpoint:0/1>If Dest. Address Mode = 0x03, then the Long Dest. Address will be used and Dest. endpoint will be included. If Dest. Address Mode = 0x01, then the Short Dest. Address will be used and there will be no Dest. endpoint.

#define

BINDING_TABLE_REQUEST 0x0033u

#define

BINDING_TABLE_RESPONSE 0x8033u

Leave Request / Response#

Request: <transaction sequence number: 1> <EUI64:8> <flags:1> The flag bits are: 0x40 remove children 0x80 rejoinResponse: <transaction sequence number: 1> <status:1>

#define

LEAVE_REQUEST 0x0034u

#define

LEAVE_RESPONSE 0x8034u

#define

LEAVE_REQUEST_REMOVE_CHILDREN_FLAG 0x40u

#define

LEAVE_REQUEST_REJOIN_FLAG 0x80u

Permit Joining Request / Response#

Request: <transaction sequence number: 1> <duration:1> <permit authentication:1>Response: <transaction sequence number: 1> <status:1>

#define

PERMIT_JOINING_REQUEST 0x0036u

#define

PERMIT_JOINING_RESPONSE 0x8036u

Network Update Request / Response#

Request: <transaction sequence number: 1> <scan channels:4> <duration:1> <count:0/1> <manager:0/2> If the duration is in 0x00 ... 0x05, 'count' is present but not 'manager'. Perform 'count' scans of the given duration on the given channels. If duration is 0xFE, 'channels' should have a single channel and 'count' and 'manager' are not present. Switch to the indicated channel. If duration is 0xFF, 'count' is not present. Set the active channels and the network manager ID to the values given. Unicast requests always get a response, which is INVALID_REQUEST if the duration is not a legal value.Response: <transaction sequence number: 1> <status:1> <scanned channels:4> <transmissions:2> <failures:2> <energy count:1> <energy:1>*

#define

NWK_UPDATE_REQUEST 0x0038u

#define

NWK_UPDATE_RESPONSE 0x8038u

#define

NWK_UPDATE_ENHANCED_REQUEST 0x0039u

#define

NWK_UPDATE_ENHANCED_RESPONSE 0x8039u

#define

NWK_UPDATE_IEEE_JOINING_LIST_REQUEST 0x003Au

#define

NWK_UPDATE_IEEE_JOINING_LIST_REPONSE 0x803Au

#define

NWK_UNSOLICITED_ENHANCED_UPDATE_NOTIFY 0x803Bu

Unsupported#

Not mandatory and not supported.

#define

COMPLEX_DESCRIPTOR_REQUEST 0x0010u

#define

COMPLEX_DESCRIPTOR_RESPONSE 0x8010u

#define

USER_DESCRIPTOR_REQUEST 0x0011u

#define

USER_DESCRIPTOR_RESPONSE 0x8011u

#define

DISCOVERY_REGISTER_REQUEST 0x0012u

#define

DISCOVERY_REGISTER_RESPONSE 0x8012u

#define

USER_DESCRIPTOR_SET 0x0014u

#define

USER_DESCRIPTOR_CONFIRM 0x8014u

#define

NETWORK_DISCOVERY_REQUEST 0x0030u

#define

NETWORK_DISCOVERY_RESPONSE 0x8030u

#define

DIRECT_JOIN_REQUEST 0x0035u

#define

DIRECT_JOIN_RESPONSE 0x8035u

#define

CLUSTER_ID_RESPONSE_MINIMUM 0x8000u

ZDO configuration flags.#

Control which ZDO requests are passed to the application. These are normally controlled via the following configuration definitions:EMBER_APPLICATION_RECEIVES_SUPPORTED_ZDO_REQUESTS EMBER_APPLICATION_HANDLES_UNSUPPORTED_ZDO_REQUESTS EMBER_APPLICATION_HANDLES_ENDPOINT_ZDO_REQUESTS EMBER_APPLICATION_HANDLES_BINDING_ZDO_REQUESTSSee ember-configuration.h for more information.

enum

EmberZdoConfigurationFlags {

EMBER_APP_RECEIVES_SUPPORTED_ZDO_REQUESTS = 0x01

EMBER_APP_HANDLES_UNSUPPORTED_ZDO_REQUESTS = 0x02

EMBER_APP_HANDLES_ZDO_ENDPOINT_REQUESTS = 0x04

EMBER_APP_HANDLES_ZDO_BINDING_REQUESTS = 0x08

}

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

enum

EmberMultiPhyNwkConfig {

EMBER_MULTI_PHY_ROUTERS_ALLOWED = 0x01

EMBER_MULTI_PHY_BROADCASTS_ENABLED = 0x02

EMBER_MULTI_PHY_DISABLED = 0x80

}

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

enum

@0 {

PRIORITIZE_BEACONS_BASED_ON_PARENT_CLASSIFICATION = 0x0001

PRIORITIZE_BEACONS_BASED_ON_TC_CONNECTVITY = 0x0002

TC_CONNECTIVITY = 0x0010

LONG_UPTIME = 0x0020

BAD_PARENT_CONNECTIVITY = 0x0040

EMBER_OUTGOING_MESSAGES = 0x0001

EMBER_INCOMING_MESSAGES = 0x0002

EMBER_RADIO_IS_ON = 0x0004

EMBER_TRANSPORT_ACTIVE = 0x0008

EMBER_APS_LAYER_ACTIVE = 0x0010

EMBER_ASSOCIATING = 0x0020

EMBER_ZLL_TOUCH_LINKING = 0x0040

EMBER_NETWORK_TIMEOUT_REQUEST = 0x0200

EMBER_SEND_ORPHAN_NOTIFICATION = 0x0400

EMBER_MAC_DATA_POLL_SUPER_RETRY = 0x0800

}

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

enum

EmberEntropySource {

EMBER_ENTROPY_SOURCE_ERROR = 0x00

EMBER_ENTROPY_SOURCE_RADIO = 0x01

EMBER_ENTROPY_SOURCE_MBEDTLS_TRNG = 0x02

EMBER_ENTROPY_SOURCE_MBEDTLS = 0x03

}

Defines the entropy source used by the stack.

enum

@1 {

EMBER_POLL_TIMEOUT_10_SECONDS = 0

EMBER_POLL_TIMEOUT_2_MINUTES = 1

EMBER_POLL_TIMEOUT_4_MINUTES = 2

EMBER_POLL_TIMEOUT_8_MINUTES = 3

EMBER_POLL_TIMEOUT_16_MINUTES = 4

EMBER_POLL_TIMEOUT_32_MINUTES = 5

EMBER_POLL_TIMEOUT_64_MINUTES = 6

EMBER_POLL_TIMEOUT_128_MINUTES = 7

EMBER_POLL_TIMEOUT_256_MINUTES = 8

EMBER_POLL_TIMEOUT_512_MINUTES = 9

EMBER_POLL_TIMEOUT_1024_MINUTES = 10

EMBER_POLL_TIMEOUT_2048_MINUTES = 11

EMBER_POLL_TIMEOUT_4096_MINUTES = 12

EMBER_POLL_TIMEOUT_8192_MINUTES = 13

EMBER_POLL_TIMEOUT_16384_MINUTES = 14

}

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

enum

EmberTcApsEncryptMode {

TC_APS_ENCRYPT_DEFAULT = 0x00

TC_APS_ENCRYPT_ENABLE = 0x01

TC_APS_ENCRYPT_DISABLE = 0x02

}

Defines the trust center APS encryption mode when sending a newer (alternate) network key to a device. The value settings below do not take effect when sending the initial network key during joining or rejoining.

typedef uint8_t

EmberRadioPowerMode

Radio power mode.

#define

WEAK_TEST

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

#define

EMBER_MAX_MAC_ONLY_COUNTERS 33u

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

#define

EMBER_MAX_NUM_PHYS 2u

Defines the maximum number of PHYs supported.

#define

PHY_INDEX_NATIVE 0u

PHY index for 2.4 GHz radio interface, valid for simultaneous multi radio network.

#define

PHY_INDEX_PRO2PLUS 1u

PHY index for Sub-GHz radio interface, valid for simultaneous multi radio network.

Enumerations#

enum

EmberNodeType {

EMBER_UNKNOWN_DEVICE = 0

EMBER_COORDINATOR = 1

EMBER_ROUTER = 2

EMBER_END_DEVICE = 3

EMBER_SLEEPY_END_DEVICE = 4

EMBER_WIREFREE_INITIATOR_DEVICE = 5

EMBER_WIREFREE_TARGET_DEVICE = 6

}

Defines the possible types of nodes and the roles that a node might play in a network.

enum

EmberEndDeviceConfiguration {

EMBER_END_DEVICE_CONFIG_NONE = 0x00

EMBER_END_DEVICE_CONFIG_PERSIST_DATA_ON_PARENT = 0x01

}

The configuration advertised by the end device to the parent when joining/rejoining.

enum

EmberNetworkInitBitmask {

EMBER_NETWORK_INIT_NO_OPTIONS = 0x0000

EMBER_NETWORK_INIT_PARENT_INFO_IN_TOKEN = 0x0001

EMBER_NETWORK_INIT_END_DEVICE_REJOIN_ON_REBOOT = 0x0002

}

Defines the options that should be used when initializing the node's network configuration.

enum

EmberApsRejoinMode {

NO_REJOIN

REJOIN_ANY_LINK_KEY

REJOIN_NON_DEFAULT_LINK_KEY

}

Options to allow/disallow rejoins using the default link key.

enum

EmberApsOption {

EMBER_APS_OPTION_NONE = 0x0000

EMBER_APS_OPTION_DSA_SIGN = 0x0010

EMBER_APS_OPTION_ENCRYPTION = 0x0020

EMBER_APS_OPTION_RETRY = 0x0040

EMBER_APS_OPTION_ENABLE_ROUTE_DISCOVERY = 0x0100

EMBER_APS_OPTION_FORCE_ROUTE_DISCOVERY = 0x0200

EMBER_APS_OPTION_SOURCE_EUI64 = 0x0400

EMBER_APS_OPTION_DESTINATION_EUI64 = 0x0800

EMBER_APS_OPTION_ENABLE_ADDRESS_DISCOVERY = 0x1000

EMBER_APS_OPTION_POLL_RESPONSE = 0x2000

EMBER_APS_OPTION_ZDO_RESPONSE_REQUIRED = 0x4000

EMBER_APS_OPTION_FRAGMENT = SIGNED_ENUM 0x8000

}

Options to use when sending a message.

enum

EmberIncomingMessageType {

EMBER_INCOMING_UNICAST

EMBER_INCOMING_UNICAST_REPLY

EMBER_INCOMING_MULTICAST

EMBER_INCOMING_MULTICAST_LOOPBACK

EMBER_INCOMING_BROADCAST

EMBER_INCOMING_BROADCAST_LOOPBACK

}

Defines the possible incoming message types.

enum

EmberOutgoingMessageType {

EMBER_OUTGOING_DIRECT

EMBER_OUTGOING_VIA_ADDRESS_TABLE

EMBER_OUTGOING_VIA_BINDING

EMBER_OUTGOING_MULTICAST

EMBER_OUTGOING_MULTICAST_WITH_ALIAS

EMBER_OUTGOING_BROADCAST_WITH_ALIAS

EMBER_OUTGOING_BROADCAST

}

Defines the possible outgoing message types.

enum

EmberZigbeeCommandType {

EMBER_ZIGBEE_COMMAND_TYPE_RAW_MAC

EMBER_ZIGBEE_COMMAND_TYPE_MAC_COMMAND

EMBER_ZIGBEE_COMMAND_TYPE_NWK

EMBER_ZIGBEE_COMMAND_TYPE_APS

EMBER_ZIGBEE_COMMAND_TYPE_ZDO

EMBER_ZIGBEE_COMMAND_TYPE_ZCL

EMBER_ZIGBEE_COMMAND_TYPE_BEACON

}

A type of command received by the stack.

enum

EmberPacketAction {

EMBER_DROP_PACKET = 0

EMBER_ACCEPT_PACKET = 1

EMBER_MANGLE_PACKET

EMBER_ACCEPT_PACKET_OVERRIDE_SECURITY

EMBER_ACCEPT_PACKET_SKIP_NWK_CRYPTO

}

indication of the action taken on a packet

enum

EmberZigbeePacketType {

EMBER_ZIGBEE_PACKET_TYPE_RAW_MAC

EMBER_ZIGBEE_PACKET_TYPE_MAC_COMMAND

EMBER_ZIGBEE_PACKET_TYPE_NWK_DATA

EMBER_ZIGBEE_PACKET_TYPE_NWK_COMMAND

EMBER_ZIGBEE_PACKET_TYPE_APS_DATA

EMBER_ZIGBEE_PACKET_TYPE_APS_COMMAND

EMBER_ZIGBEE_PACKET_TYPE_ZDO

EMBER_ZIGBEE_PACKET_TYPE_ZCL

EMBER_ZIGBEE_PACKET_TYPE_BEACON

EMBER_ZIGBEE_PACKET_TYPE_INTERPAN

EMBER_ZIGBEE_PACKET_TYPE_NWK_DATA_PRE_DECRYPTION

EMBER_ZIGBEE_PACKET_TYPE_NWK_COMMAND_PRE_DECRYPTION

}

A type of packet received by the stack.

enum

EmberNetworkStatus {

EMBER_NO_NETWORK

EMBER_JOINING_NETWORK

EMBER_JOINED_NETWORK

EMBER_JOINED_NETWORK_NO_PARENT

EMBER_JOINED_NETWORK_WF_INITIATOR

EMBER_JOINED_NETWORK_WF_TARGET

EMBER_LEAVING_NETWORK

}

Defines the possible join states for a node.

enum

EmberNetworkScanType {

EMBER_ENERGY_SCAN

EMBER_ACTIVE_SCAN

EMBER_START_RADIO_OFF_SCAN

EMBER_STACK_GP_CHANNEL_DELIVERY_SCAN

EMBER_ACTIVE_SCAN_ROUTER

EMBER_LAST_SCAN_TYPE = EMBER_ACTIVE_SCAN_ROUTER

}

Type for a network scan.

enum

EmberBindingType {

EMBER_UNUSED_BINDING = 0

EMBER_UNICAST_BINDING = 1

EMBER_MANY_TO_ONE_BINDING = 2

EMBER_MULTICAST_BINDING = 3

}

Defines binding types.

enum

EmberKeepAliveMode {

EMBER_KEEP_ALIVE_SUPPORT_UNKNOWN = 0x00

EMBER_MAC_DATA_POLL_KEEP_ALIVE = 0x01

EMBER_END_DEVICE_TIMEOUT_KEEP_ALIVE = 0x02

EMBER_KEEP_ALIVE_SUPPORT_ALL = 0x03

}

Type of Ember keep alive method defining the keep alive message type that a parent accepts to prevent child aging. This is configured in a parent router and communicated and stored in an end-device.

enum

EmberSourceRouteDiscoveryMode {

EMBER_SOURCE_ROUTE_DISCOVERY_OFF = 0x00

EMBER_SOURCE_ROUTE_DISCOVERY_ON = 0x01

EMBER_SOURCE_ROUTE_DISCOVERY_RESCHEDULE = 0x02

}

Types of source route discovery modes used by the concentrator.

enum

EmberTransmitPriority {

EMBER_MAC_TRANSMIT_PRIORITY_HIGH

EMBER_MAC_TRANSMIT_PRIORITY_NORMAL

EMBER_MAC_TRANSMIT_PRIORITY_SCAN_OKAY

}

Packet transmit priorities in terms of getting into the MAC queue.

enum

sl_zigbee_route_record_policy_type_t {

ROUTE_RECORD_POLICY_ACK_BY_SOURCE_ROUTED_MESSAGE = 0

ROUTE_RECORD_POLICY_DONT_SEND = 1

ROUTE_RECORD_POLICY_NO_ACK_REQUIRED = 2

}

Policies for sending a route record to the concentrator.

Macros#

#define

EMBER_MIN_BROADCAST_ADDRESS 0xFFF8u

#define

emberIsZigbeeBroadcastAddress (address)

Returns true if nodeId (short address) is a broadcast address.

Miscellaneous Ember Types Documentation#

EmberVersionType#

EmberVersionType

Type of Ember software version.

Enumerator
EMBER_VERSION_TYPE_PRE_RELEASE
EMBER_VERSION_TYPE_ALPHA_1
EMBER_VERSION_TYPE_ALPHA_2
EMBER_VERSION_TYPE_ALPHA_3
EMBER_VERSION_TYPE_BETA_1
EMBER_VERSION_TYPE_BETA_2
EMBER_VERSION_TYPE_BETA_3
EMBER_VERSION_TYPE_GA

Definition at line 53 of file stack/include/ember-types.h

EmberStackProfile#

EmberStackProfile

EmberReleaseTypeStruct Data that relates release type to the correct string.

Enumerator
EMBER_STACK_PROFILE_NONE
EMBER_STACK_PROFILE_ZIGBEE_PRO

Definition at line 447 of file stack/include/ember-types.h

EmberSecurityLevel#

EmberSecurityLevel

EmberReleaseTypeStruct Data that relates release type to the correct string.

Enumerator
EMBER_SECURITY_LEVEL_NONE
EMBER_SECURITY_LEVEL_Z3

Definition at line 458 of file stack/include/ember-types.h

EmberLeaveRequestFlags#

EmberLeaveRequestFlags

EmberReleaseTypeStruct Data that relates release type to the correct string.

Enumerator
EMBER_ZIGBEE_LEAVE_AND_REJOIN	Leave and rejoin.
EMBER_ZIGBEE_LEAVE_WITHOUT_REJOIN	Leave.

Definition at line 469 of file stack/include/ember-types.h

EmberLeaveReason#

EmberLeaveReason

EmberReleaseTypeStruct Data that relates release type to the correct string.

Enumerator
EMBER_LEAVE_REASON_NONE
EMBER_LEAVE_DUE_TO_NWK_LEAVE_MESSAGE
EMBER_LEAVE_DUE_TO_APS_REMOVE_MESSAGE
EMBER_LEAVE_DUE_TO_ZDO_LEAVE_MESSAGE
EMBER_LEAVE_DUE_TO_ZLL_TOUCHLINK
EMBER_LEAVE_DUE_TO_APP_EVENT_1

Definition at line 489 of file stack/include/ember-types.h

EmberMulticastId#

typedef uint16_t EmberMulticastId

16-bit ZigBee network address.

16-bit ZigBee multicast group identifier.

Definition at line 224 of file stack/include/ember-types.h

EmberDutyCycleHectoPct#

typedef uint16_t EmberDutyCycleHectoPct

802.15.4 PAN ID.

The percent of duty cycle for a limit.

Duty cycle, limits, and thresholds are reported in units of percent * 100 (i.e., 10000 = 100.00%, 1 = 0.01%).

Definition at line 237 of file stack/include/ember-types.h

emberVersion#

const EmberVersion emberVersion

A structure containing the version information.

Definition at line 115 of file stack/include/ember-types.h

EMBER_RELEASE_TYPE_TO_STRING_STRUCT_DATA#

#define EMBER_RELEASE_TYPE_TO_STRING_STRUCT_DATA

Value:

{ EMBER_VERSION_TYPE_PRE_RELEASE, "Pre-Release" }, \

{ EMBER_VERSION_TYPE_ALPHA_1, "Alpha 1" }, \

{ EMBER_VERSION_TYPE_ALPHA_2, "Alpha 2" }, \

{ EMBER_VERSION_TYPE_ALPHA_3, "Alpha 3" }, \

{ EMBER_VERSION_TYPE_BETA_1, "Beta 1" }, \

{ EMBER_VERSION_TYPE_BETA_2, "Beta 2" }, \

{ EMBER_VERSION_TYPE_BETA_3, "Beta 3" }, \

{ EMBER_VERSION_TYPE_GA, "GA" }, \

{ 0xFF, NULL },

EmberReleaseTypeStruct Data that relates release type to the correct string.

Definition at line 89 of file stack/include/ember-types.h

EUI64_SIZE#

#define EUI64_SIZE

Value:

Size of EUI64 (an IEEE address) in bytes (8).

Definition at line 120 of file stack/include/ember-types.h

EXTENDED_PAN_ID_SIZE#

#define EXTENDED_PAN_ID_SIZE

Value:

Size of an extended PAN identifier in bytes (8).

Definition at line 125 of file stack/include/ember-types.h

EMBER_ENCRYPTION_KEY_SIZE#

#define EMBER_ENCRYPTION_KEY_SIZE

Value:

Size of an encryption key in bytes (16).

Definition at line 130 of file stack/include/ember-types.h

EMBER_CERTIFICATE_SIZE#

#define EMBER_CERTIFICATE_SIZE

Value:

Size of Implicit Certificates used for Certificate-based Key Exchange(CBKE).

Definition at line 136 of file stack/include/ember-types.h

EMBER_PUBLIC_KEY_SIZE#

#define EMBER_PUBLIC_KEY_SIZE

Value:

Size of Public Keys used in Elliptical Cryptography ECMQV algorithms.

Definition at line 141 of file stack/include/ember-types.h

EMBER_PRIVATE_KEY_SIZE#

#define EMBER_PRIVATE_KEY_SIZE

Value:

Size of Private Keys used in Elliptical Cryptography ECMQV algorithms.

Definition at line 146 of file stack/include/ember-types.h

EMBER_SMAC_SIZE#

#define EMBER_SMAC_SIZE

Value:

Size of the SMAC used in Elliptical Cryptography ECMQV algorithms.

Definition at line 151 of file stack/include/ember-types.h

EMBER_SIGNATURE_SIZE#

#define EMBER_SIGNATURE_SIZE

Value:

Size of the DSA signature used in Elliptical Cryptography Digital Signature Algorithms.

Definition at line 157 of file stack/include/ember-types.h

EMBER_AES_HASH_BLOCK_SIZE#

#define EMBER_AES_HASH_BLOCK_SIZE

Value:

The size of AES-128 MMO hash is 16-bytes. This is defined in the core. ZigBee specification.

Definition at line 162 of file stack/include/ember-types.h

EMBER_CERTIFICATE_283K1_SIZE#

#define EMBER_CERTIFICATE_283K1_SIZE

Value:

Size of Implicit Certificates used for Certificate Based Key Exchange using the ECC283K1 curve in bytes.

Definition at line 168 of file stack/include/ember-types.h

EMBER_PUBLIC_KEY_283K1_SIZE#

#define EMBER_PUBLIC_KEY_283K1_SIZE

Value:

Size of Public Keys used in SECT283k1 Elliptical Cryptography ECMQV algorithms.

Definition at line 173 of file stack/include/ember-types.h

EMBER_PRIVATE_KEY_283K1_SIZE#

#define EMBER_PRIVATE_KEY_283K1_SIZE

Value:

Size of Private Keys used SECT283k1 in Elliptical Cryptography ECMQV algorithms.

Definition at line 178 of file stack/include/ember-types.h

EMBER_SIGNATURE_283K1_SIZE#

#define EMBER_SIGNATURE_283K1_SIZE

Value:

Size of the DSA signature used in SECT283k1 Elliptical Cryptography Digital Signature Algorithms.

Definition at line 184 of file stack/include/ember-types.h

__EMBERSTATUS_TYPE__#

#define __EMBERSTATUS_TYPE__

Return type for Ember functions.

Definition at line 190 of file stack/include/ember-types.h

NULL_BUFFER#

#define NULL_BUFFER

Value:

0x0000u

EUI 64-bit ID (an IEEE address).

Incoming and outgoing messages are stored in buffers. These buffers are allocated and freed as needed.

Buffers are 32 bytes in length and can be linked together to hold longer messages.

See packet-buffer.h for APIs related to stack and linked buffers.

Definition at line 216 of file stack/include/ember-types.h

EMBER_MAX_802_15_4_CHANNEL_NUMBER#

#define EMBER_MAX_802_15_4_CHANNEL_NUMBER

Value:

The maximum 802.15.4 channel number is 26.

Definition at line 242 of file stack/include/ember-types.h

EMBER_MIN_802_15_4_CHANNEL_NUMBER#

#define EMBER_MIN_802_15_4_CHANNEL_NUMBER

Value:

The minimum 2.4GHz 802.15.4 channel number is 11.

Definition at line 247 of file stack/include/ember-types.h

EMBER_MIN_SUBGHZ_CHANNEL_NUMBER#

#define EMBER_MIN_SUBGHZ_CHANNEL_NUMBER

Value:

The minimum SubGhz channel number is 0.

Definition at line 252 of file stack/include/ember-types.h

EMBER_ACTIVE_SCAN_DURATION#

#define EMBER_ACTIVE_SCAN_DURATION

Value:

ZigBee protocol specifies that active scans have a duration of 3 (138 msec). See documentation for emberStartScan in include/network-formation.h for more info on duration values.

Definition at line 259 of file stack/include/ember-types.h

EMBER_SUB_GHZ_SCAN_DURATION#

#define EMBER_SUB_GHZ_SCAN_DURATION

Value:

The SubGhz scan duration is 5.

Definition at line 264 of file stack/include/ember-types.h

EMBER_NUM_802_15_4_CHANNELS#

#define EMBER_NUM_802_15_4_CHANNELS

Value:

  (EMBER_MAX_802_15_4_CHANNEL_NUMBER - EMBER_MIN_802_15_4_CHANNEL_NUMBER + 1)

There are sixteen 802.15.4 channels.

Definition at line 269 of file stack/include/ember-types.h

EMBER_ALL_802_15_4_CHANNELS_MASK#

#define EMBER_ALL_802_15_4_CHANNELS_MASK

Value:

0x07FFF800UL

A bitmask to scan all 2.4 GHz 802.15.4 channels.

Definition at line 275 of file stack/include/ember-types.h

EMBER_MAX_CHANNELS_PER_PAGE#

#define EMBER_MAX_CHANNELS_PER_PAGE

Value:

The maximum channels per page are 27 page bits 31...27, channel bits 26...0.

Definition at line 281 of file stack/include/ember-types.h

EMBER_ALL_SUBGHZ_CHANNELS_MASK_FOR_PAGES_28_30_31#

#define EMBER_ALL_SUBGHZ_CHANNELS_MASK_FOR_PAGES_28_30_31

Value:

0x07FFFFFFUL

Sub-GHz channel bitmasks for pages 28, 30, 31.

Definition at line 286 of file stack/include/ember-types.h

EMBER_MAX_SUBGHZ_CHANNEL_NUMBER_ON_PAGES_28_30_31#

#define EMBER_MAX_SUBGHZ_CHANNEL_NUMBER_ON_PAGES_28_30_31

Value:

The maximum SubGhz channel number on pages 28, 30, 31 is 26.

Definition at line 291 of file stack/include/ember-types.h

EMBER_ALL_SUBGHZ_CHANNELS_MASK_FOR_PAGES_29#

#define EMBER_ALL_SUBGHZ_CHANNELS_MASK_FOR_PAGES_29

Value:

0x1FF

SubGhz channel bitmasks for page 29.

Definition at line 295 of file stack/include/ember-types.h

EMBER_MAX_SUBGHZ_CHANNEL_NUMBER_ON_PAGE_29#

#define EMBER_MAX_SUBGHZ_CHANNEL_NUMBER_ON_PAGE_29

Value:

The maximum SubGhz channel number on page 29 is 8.

Definition at line 300 of file stack/include/ember-types.h

EMBER_MIN_SUGBHZ_PAGE_NUMBER#

#define EMBER_MIN_SUGBHZ_PAGE_NUMBER

Value:

The minimum SubGhz page number is 28.

Definition at line 305 of file stack/include/ember-types.h

EMBER_MAX_SUGBHZ_PAGE_NUMBER#

#define EMBER_MAX_SUGBHZ_PAGE_NUMBER

Value:

The maximum SubGhz page number is 31.

Definition at line 310 of file stack/include/ember-types.h

EMBER_ALL_CHANNEL_PAGE_MASK#

#define EMBER_ALL_CHANNEL_PAGE_MASK

Value:

0xF8000000UL

A bitmask for the channel page within a channel mask.

Definition at line 315 of file stack/include/ember-types.h

EMBER_PAGE_CHANNEL_MASK_FROM_CHANNEL_MASK#

#define EMBER_PAGE_CHANNEL_MASK_FROM_CHANNEL_MASK

Value:

(((((uint32_t)(page)) << EMBER_MAX_CHANNELS_PER_PAGE) & EMBER_ALL_CHANNEL_PAGE_MASK) \

| (((uint32_t)(mask)) & ~EMBER_ALL_CHANNEL_PAGE_MASK))

A page-channel mask for a given page and channel mask.

Definition at line 320 of file stack/include/ember-types.h

EMBER_PAGE_CHANNEL_MASK_FROM_CHANNEL_NUMBER#

#define EMBER_PAGE_CHANNEL_MASK_FROM_CHANNEL_NUMBER

Value:

(page, channel)

A page-channel mask for a given page and channel.

Definition at line 327 of file stack/include/ember-types.h

EMBER_ZIGBEE_COORDINATOR_ADDRESS#

#define EMBER_ZIGBEE_COORDINATOR_ADDRESS

Value:

0x0000u

The network ID of the coordinator in a ZigBee network is 0x0000.

Definition at line 333 of file stack/include/ember-types.h

EMBER_NULL_NODE_ID#

#define EMBER_NULL_NODE_ID

Value:

0xFFFFu

A distinguished network ID that will never be assigned to any node. It is used to indicate the absence of a node ID.

Definition at line 339 of file stack/include/ember-types.h

EMBER_NO_CHANNEL_PAGE_IN_USE#

#define EMBER_NO_CHANNEL_PAGE_IN_USE

Value:

The channel page value used to indicate just the 2.4GHz channels.

Definition at line 344 of file stack/include/ember-types.h

EMBER_NULL_EUI64#

#define EMBER_NULL_EUI64

Value:

{ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF }

A distinguished EUI64 that is commonly used to indicate an invalid EUI64.

Definition at line 349 of file stack/include/ember-types.h

EMBER_NULL_BINDING#

#define EMBER_NULL_BINDING

Value:

0xFFu

A distinguished binding index used to indicate the absence of a binding.

Definition at line 355 of file stack/include/ember-types.h

EMBER_TABLE_ENTRY_UNUSED_NODE_ID#

#define EMBER_TABLE_ENTRY_UNUSED_NODE_ID

Value:

0xFFFFu

A distinguished network ID that will never be assigned to any node.

This value is used when setting or getting the remote node ID in the address table or getting the remote node ID from the binding table. It indicates that the address or binding table entry is not in use.

Definition at line 366 of file stack/include/ember-types.h

EMBER_MULTICAST_NODE_ID#

#define EMBER_MULTICAST_NODE_ID

Value:

0xFFFEu

Definition at line 374 of file stack/include/ember-types.h

EMBER_UNKNOWN_NODE_ID#

#define EMBER_UNKNOWN_NODE_ID

Value:

0xFFFDu

Definition at line 383 of file stack/include/ember-types.h

EMBER_DISCOVERY_ACTIVE_NODE_ID#

#define EMBER_DISCOVERY_ACTIVE_NODE_ID

Value:

0xFFFCu

Definition at line 392 of file stack/include/ember-types.h

EMBER_NULL_ADDRESS_TABLE_INDEX#

#define EMBER_NULL_ADDRESS_TABLE_INDEX

Value:

0xFFu

A distinguished address table index used to indicate the absence of an address table entry.

Definition at line 398 of file stack/include/ember-types.h

EMBER_ZDO_ENDPOINT#

#define EMBER_ZDO_ENDPOINT

Value:

0u

The endpoint where the ZigBee Device Object (ZDO) resides.

Definition at line 403 of file stack/include/ember-types.h

EMBER_BROADCAST_ENDPOINT#

#define EMBER_BROADCAST_ENDPOINT

Value:

0xFFu

The broadcast endpoint, as defined in the ZigBee spec.

Definition at line 408 of file stack/include/ember-types.h

EMBER_ZDO_PROFILE_ID#

#define EMBER_ZDO_PROFILE_ID

Value:

0x0000u

The profile ID used by the ZigBee Device Object (ZDO).

Definition at line 413 of file stack/include/ember-types.h

EMBER_WILDCARD_PROFILE_ID#

#define EMBER_WILDCARD_PROFILE_ID

Value:

0xFFFFu

The profile ID used to address all the public profiles.

Definition at line 418 of file stack/include/ember-types.h

EMBER_MAXIMUM_STANDARD_PROFILE_ID#

#define EMBER_MAXIMUM_STANDARD_PROFILE_ID

Value:

0x7FFFu

The maximum value for a profile ID in the standard profile range.

Definition at line 423 of file stack/include/ember-types.h

EMBER_BROADCAST_TABLE_TIMEOUT_QS#

#define EMBER_BROADCAST_TABLE_TIMEOUT_QS

Value:

(20 * 4)

The broadcast table entry timeout, which specifies, in quarter seconds, how long an entry persists in the local device's broadcast table.

Definition at line 429 of file stack/include/ember-types.h

EMBER_MANUFACTURER_ID#

#define EMBER_MANUFACTURER_ID

Value:

0x1002u

Ember's Manufacturer ID.

Definition at line 434 of file stack/include/ember-types.h

EMBER_NULL_NETWORK_INDEX#

#define EMBER_NULL_NETWORK_INDEX

Value:

0xFFu

An invalid network index.

Definition at line 439 of file stack/include/ember-types.h

EMBER_DC_LIMIT_USE_DEFAULT#

#define EMBER_DC_LIMIT_USE_DEFAULT

Value:

Use Ember's default duty cycle limit configurations.

Definition at line 444 of file stack/include/ember-types.h

ZigBee Broadcast Addresses Documentation#

EMBER_BROADCAST_ADDRESS#

#define EMBER_BROADCAST_ADDRESS

Value:

0xFFFCu

Broadcast to all routers.

Definition at line 519 of file stack/include/ember-types.h

EMBER_RX_ON_WHEN_IDLE_BROADCAST_ADDRESS#

#define EMBER_RX_ON_WHEN_IDLE_BROADCAST_ADDRESS

Value:

0xFFFDu

Broadcast to all non-sleepy devices.

Definition at line 521 of file stack/include/ember-types.h

EMBER_SLEEPY_BROADCAST_ADDRESS#

#define EMBER_SLEEPY_BROADCAST_ADDRESS

Value:

0xFFFFu

Broadcast to all devices, including sleepy end devices.

Definition at line 523 of file stack/include/ember-types.h

Ember Concentrator Types Documentation#

EmberAssumeTrustCenterConcentratorType#

EmberAssumeTrustCenterConcentratorType

Enumerator
EMBER_ASSUME_TRUST_CENTER_IS_NOT_A_CONCENTRATOR	To assume trust center is not a concentrator.
EMBER_ASSUME_TRUST_CENTER_IS_LOW_RAM_CONCENTRATOR	To assume trust center is a low RAM concentrator.
EMBER_ASSUME_TRUST_CENTER_IS_HIGH_RAM_CONCENTRATOR	To assume trust center is a high RAM concentrator.

Definition at line 1018 of file stack/include/ember-types.h

EmberJoinDecision#

EmberJoinDecision

The decision made by the Trust Center when a node attempts to join.

Enumerator
EMBER_USE_PRECONFIGURED_KEY	Allow the node to join. The node has the key.
EMBER_SEND_KEY_IN_THE_CLEAR	Allow the node to join. Send the key to the node.
EMBER_DENY_JOIN	Deny join.
EMBER_NO_ACTION	Take no action.
EMBER_ALLOW_REJOINS_ONLY	Allow rejoins only.

Definition at line 1036 of file stack/include/ember-types.h

EmberDeviceUpdate#

EmberDeviceUpdate

Enumerator
EMBER_STANDARD_SECURITY_SECURED_REJOIN
EMBER_STANDARD_SECURITY_UNSECURED_JOIN
EMBER_DEVICE_LEFT
EMBER_STANDARD_SECURITY_UNSECURED_REJOIN

Definition at line 1071 of file stack/include/ember-types.h

EmberRejoinReason#

EmberRejoinReason

Notes the last rejoin reason.

Enumerator
EMBER_REJOIN_REASON_NONE
EMBER_REJOIN_DUE_TO_NWK_KEY_UPDATE
EMBER_REJOIN_DUE_TO_LEAVE_MESSAGE
EMBER_REJOIN_DUE_TO_NO_PARENT
EMBER_REJOIN_DUE_TO_ZLL_TOUCHLINK
EMBER_REJOIN_DUE_TO_END_DEVICE_REBOOT
EMBER_REJOIN_DUE_TO_APP_EVENT_5
EMBER_REJOIN_DUE_TO_APP_EVENT_4
EMBER_REJOIN_DUE_TO_APP_EVENT_3
EMBER_REJOIN_DUE_TO_APP_EVENT_2
EMBER_REJOIN_DUE_TO_APP_EVENT_1

Definition at line 1096 of file stack/include/ember-types.h

EmberClusterListId#

EmberClusterListId

Defines the lists of clusters that must be provided for each endpoint.

Enumerator
EMBER_INPUT_CLUSTER_LIST	Input clusters the endpoint will accept.
EMBER_OUTPUT_CLUSTER_LIST	Output clusters the endpoint can send.

Definition at line 1127 of file stack/include/ember-types.h

EmberEventUnits#

EmberEventUnits

Either marks an event as inactive or specifies the units for the event execution time.

Enumerator
EMBER_EVENT_INACTIVE	The event is not scheduled to run.
EMBER_EVENT_MS_TIME	The execution time is in approximate milliseconds.
EMBER_EVENT_QS_TIME	The execution time is in 'binary' quarter seconds (256 approximate milliseconds each).
EMBER_EVENT_MINUTE_TIME	The execution time is in 'binary' minutes (65536 approximate milliseconds each).
EMBER_EVENT_ZERO_DELAY	The event is scheduled to run at the earliest opportunity.

Definition at line 1144 of file stack/include/ember-types.h

EmberJoinMethod#

EmberJoinMethod

The type of method used for joining.

Enumerator
EMBER_USE_MAC_ASSOCIATION	Devices normally use MAC association to join a network, which respects the "permit joining" flag in the MAC beacon. This value should be used by default.
EMBER_USE_NWK_REJOIN	For networks where the "permit joining" flag is never turned on, devices will need to use a ZigBee NWK Rejoin. This value causes the rejoin to be sent withOUT NWK security and the Trust Center will be asked to send the NWK key to the device. The NWK key sent to the device can be encrypted with the device's corresponding Trust Center link key. That is determined by the EmberJoinDecision on the Trust Center returned by the emberTrustCenterJoinHandler().
EMBER_USE_NWK_REJOIN_HAVE_NWK_KEY
EMBER_USE_CONFIGURED_NWK_STATE	For networks where all network and security information is known ahead of time, a router device may be commissioned such that it does not need to send any messages to begin communicating on the network.

Definition at line 1168 of file stack/include/ember-types.h

EmberCounterType#

EmberCounterType

Defines the events reported to the application by the emberCounterHandler().

Enumerator
EMBER_COUNTER_MAC_RX_BROADCAST	The MAC received a broadcast.
EMBER_COUNTER_MAC_TX_BROADCAST	The MAC transmitted a broadcast.
EMBER_COUNTER_MAC_RX_UNICAST	The MAC received a unicast.
EMBER_COUNTER_MAC_TX_UNICAST_SUCCESS	The MAC successfully transmitted a unicast.
EMBER_COUNTER_MAC_TX_UNICAST_RETRY	The MAC retried a unicast. This is a placeholder and is not used by the emberCounterHandler() callback. Instead, the number of MAC retries are returned in the data parameter of the callback for the `EMBER_COUNTER_MAC_TX_UNICAST_SUCCESS` and `EMBER_COUNTER_MAC_TX_UNICAST_FAILED` types.
EMBER_COUNTER_MAC_TX_UNICAST_FAILED	The MAC unsuccessfully transmitted a unicast.
EMBER_COUNTER_APS_DATA_RX_BROADCAST	The APS layer received a data broadcast.
EMBER_COUNTER_APS_DATA_TX_BROADCAST	The APS layer transmitted a data broadcast.
EMBER_COUNTER_APS_DATA_RX_UNICAST	The APS layer received a data unicast.
EMBER_COUNTER_APS_DATA_TX_UNICAST_SUCCESS	The APS layer successfully transmitted a data unicast.
EMBER_COUNTER_APS_DATA_TX_UNICAST_RETRY	The APS layer retried a data unicast. This is a placeholder and is not used by the `emberCounterHandler()` callback. Instead, the number of APS retries are returned in the data parameter of the callback for the `EMBER_COUNTER_APS_DATA_TX_UNICAST_SUCCESS` and `EMBER_COUNTER_APS_DATA_TX_UNICAST_FAILED` types.
EMBER_COUNTER_APS_DATA_TX_UNICAST_FAILED	The APS layer unsuccessfully transmitted a data unicast.
EMBER_COUNTER_ROUTE_DISCOVERY_INITIATED	The network layer successfully submitted a new route discovery to the MAC.
EMBER_COUNTER_NEIGHBOR_ADDED	An entry was added to the neighbor table.
EMBER_COUNTER_NEIGHBOR_REMOVED	An entry was removed from the neighbor table.
EMBER_COUNTER_NEIGHBOR_STALE	A neighbor table entry became stale because it had not been heard from.
EMBER_COUNTER_JOIN_INDICATION	A node joined or rejoined to the network via this node.
EMBER_COUNTER_CHILD_REMOVED	An entry was removed from the child table.
EMBER_COUNTER_ASH_OVERFLOW_ERROR	EZSP-UART only. An overflow error occurred in the UART.
EMBER_COUNTER_ASH_FRAMING_ERROR	EZSP-UART only. A framing error occurred in the UART.
EMBER_COUNTER_ASH_OVERRUN_ERROR	EZSP-UART only. An overrun error occurred in the UART.
EMBER_COUNTER_NWK_FRAME_COUNTER_FAILURE	A message was dropped at the Network layer because the NWK frame counter was not higher than the last message seen from that source.
EMBER_COUNTER_APS_FRAME_COUNTER_FAILURE	A message was dropped at the APS layer because the APS frame counter was not higher than the last message seen from that source.
EMBER_COUNTER_ASH_XOFF	EZSP-UART only. An XOFF was transmitted by the UART.
EMBER_COUNTER_APS_LINK_KEY_NOT_AUTHORIZED	An encrypted message was dropped by the APS layer because the sender's key has not been authenticated. As a result, the key is not authorized for use in APS data messages.
EMBER_COUNTER_NWK_DECRYPTION_FAILURE	A NWK encrypted message was received but dropped because decryption failed.
EMBER_COUNTER_APS_DECRYPTION_FAILURE	An APS encrypted message was received but dropped because decryption failed.
EMBER_COUNTER_ALLOCATE_PACKET_BUFFER_FAILURE	The number of failures to allocate a set of linked packet buffers. This doesn't necessarily mean that the packet buffer count was 0 at the time, but that the number requested was greater than the number free.
EMBER_COUNTER_RELAYED_UNICAST	The number of relayed unicast packets.
EMBER_COUNTER_PHY_TO_MAC_QUEUE_LIMIT_REACHED	The number of times a packet was dropped due to reaching the preset PHY-to-MAC queue limit (emMaxPhyToMacQueueLength). The limit will determine how many messages are accepted by the PHY between calls to emberTick(). After that limit is reached, packets will be dropped. The number of dropped packets will be recorded in this counter. NOTE: For each call to emberCounterHandler() there may be more than 1 packet that was dropped due to the limit reached. The actual number of packets dropped will be returned in the 'data' parameter passed to that function.
EMBER_COUNTER_PACKET_VALIDATE_LIBRARY_DROPPED_COUNT	The number of times a packet was dropped due to the packet-validate library checking a packet and rejecting it due to length or other formatting problems.
EMBER_COUNTER_TYPE_NWK_RETRY_OVERFLOW	The number of times the NWK retry queue is full and a new message failed to be added.
EMBER_COUNTER_PHY_CCA_FAIL_COUNT	The number of times the PHY layer was unable to transmit due to a failed CCA.
EMBER_COUNTER_BROADCAST_TABLE_FULL	The number of times a NWK broadcast was dropped because the broadcast table was full.
EMBER_COUNTER_PTA_LO_PRI_REQUESTED	The number of times a low-priority packet traffic arbitration request has been made.
EMBER_COUNTER_PTA_HI_PRI_REQUESTED	The number of times a high-priority packet traffic arbitration request has been made.
EMBER_COUNTER_PTA_LO_PRI_DENIED	The number of times a low-priority packet traffic arbitration request has been denied.
EMBER_COUNTER_PTA_HI_PRI_DENIED	The number of times a high-priority packet traffic arbitration request has been denied.
EMBER_COUNTER_PTA_LO_PRI_TX_ABORTED	The number of times a low-priority packet traffic arbitration transmission has been aborted.
EMBER_COUNTER_PTA_HI_PRI_TX_ABORTED	The number of times a high-priority packet traffic arbitration transmission has been aborted.
EMBER_COUNTER_ADDRESS_CONFLICT_SENT	The number of times an address conflict has caused node_id change, and an address conflict error is sent
EMBER_COUNTER_TYPE_COUNT	A placeholder giving the number of Ember counter types.

Definition at line 1409 of file stack/include/ember-types.h

EmberTaskId#

typedef uint8_t EmberTaskId

brief An identifier for a task.

Definition at line 1649 of file stack/include/ember-types.h

EMBER_LOW_RAM_CONCENTRATOR#

#define EMBER_LOW_RAM_CONCENTRATOR

Value:

0xFFF8u

A concentrator with insufficient memory to store source routes for the entire network. Route records are sent to the concentrator prior to every inbound APS unicast.

Definition at line 998 of file stack/include/ember-types.h

EMBER_HIGH_RAM_CONCENTRATOR#

#define EMBER_HIGH_RAM_CONCENTRATOR

Value:

0xFFF9u

A concentrator with sufficient memory to store source routes for the entire network. Remote nodes stop sending route records once the concentrator has successfully received one.

Definition at line 1003 of file stack/include/ember-types.h

EMBER_JOIN_DECISION_STRINGS#

#define EMBER_JOIN_DECISION_STRINGS

Value:

"use preconfigured key", \

"send key in the clear", \

"deny join", \

"no action",

@ brief Defines the CLI enumerations for the EmberJoinDecision enum.

Definition at line 1057 of file stack/include/ember-types.h

EMBER_DEVICE_UPDATE_STRINGS#

#define EMBER_DEVICE_UPDATE_STRINGS

Value:

"secured rejoin", \

"UNsecured join", \

"device left", \

"UNsecured rejoin",

@ brief Defines the CLI enumerations for the EmberDeviceUpdate enum.

Definition at line 1086 of file stack/include/ember-types.h

emberInitializeNetworkParameters#

#define emberInitializeNetworkParameters

Value:

(parameters)

A concentrator with insufficient memory to store source routes for the entire network. Route records are sent to the concentrator prior to every inbound APS unicast.

Definition at line 1247 of file stack/include/ember-types.h

EMBER_COUNTER_STRINGS#

#define EMBER_COUNTER_STRINGS

@ brief Defines the CLI enumerations for the EmberCounterType enum.

Definition at line 1593 of file stack/include/ember-types.h

txPowerModes for emberSetTxPowerMode and mfglibSetPower Documentation#

EMBER_TX_POWER_MODE_DEFAULT#

#define EMBER_TX_POWER_MODE_DEFAULT

Value:

0x0000

Definition at line 1707 of file stack/include/ember-types.h

EMBER_TX_POWER_MODE_BOOST#

#define EMBER_TX_POWER_MODE_BOOST

Value:

0x0001

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable boost power mode.

Definition at line 1711 of file stack/include/ember-types.h

EMBER_TX_POWER_MODE_ALTERNATE#

#define EMBER_TX_POWER_MODE_ALTERNATE

Value:

0x0002

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable the alternate transmitter output.

Definition at line 1716 of file stack/include/ember-types.h

EMBER_TX_POWER_MODE_BOOST_AND_ALTERNATE#

#define EMBER_TX_POWER_MODE_BOOST_AND_ALTERNATE

Value:

(EMBER_TX_POWER_MODE_BOOST \

| EMBER_TX_POWER_MODE_ALTERNATE)

The application should call emberSetTxPowerMode() with the txPowerMode parameter set to this value to enable both boost mode and the alternate transmitter output.

Definition at line 1721 of file stack/include/ember-types.h

Counters Request Definitions Documentation#

EmberInitialSecurityBitmask#

EmberInitialSecurityBitmask

This is the Initial Security Bitmask that controls the use of various security features.

Enumerator
EMBER_DISTRIBUTED_TRUST_CENTER_MODE	Enables Distributed Trust Center Mode for the device forming the network. (Previously known as EMBER_NO_TRUST_CENTER_MODE)
EMBER_TRUST_CENTER_GLOBAL_LINK_KEY	Enables a Global Link Key for the Trust Center. All nodes will share the same Trust Center Link Key.
EMBER_PRECONFIGURED_NETWORK_KEY_MODE	Enables devices that perform MAC Association with a pre-configured Network Key to join the network. It is only set on the Trust Center.
EMBER_HAVE_TRUST_CENTER_EUI64	This denotes that the EmberInitialSecurityState::preconfiguredTrustCenterEui64 has a value in it containing the trust center EUI64. The device will only join a network and accept commands from a trust center with that EUI64. Normally this bit is NOT set and the EUI64 of the trust center is learned during the join process. When commissioning a device to join onto an existing network that is using a trust center and without sending any messages, this bit must be set and the field EmberInitialSecurityState::preconfiguredTrustCenterEui64 must be populated with the appropriate EUI64.
EMBER_TRUST_CENTER_USES_HASHED_LINK_KEY	This denotes that the EmberInitialSecurityState::preconfiguredKey is not the actual Link Key but a Root Key known only to the Trust Center. It is hashed with the IEEE Address of the destination device to create the actual Link Key used in encryption. This is bit is only used by the Trust Center. The joining device need not set this.
EMBER_HAVE_PRECONFIGURED_KEY	This denotes that the EmberInitialSecurityState::preconfiguredKey element has valid data that should be used to configure the initial security state.
EMBER_HAVE_NETWORK_KEY	This denotes that the EmberInitialSecurityState::networkKey element has valid data that should be used to configure the initial security state.
EMBER_GET_LINK_KEY_WHEN_JOINING	This denotes to a joining node that it should attempt to acquire a Trust Center Link Key during joining. This is necessary if the device does not have a pre-configured key, or wants to obtain a new one (since it may be using a well-known key during joining).
EMBER_REQUIRE_ENCRYPTED_KEY	This denotes that a joining device should only accept an encrypted network key from the Trust Center (using its pre-configured key). A key sent in-the-clear by the Trust Center will be rejected and the join will fail. This option is only valid when using a pre-configured key.
EMBER_NO_FRAME_COUNTER_RESET	This denotes whether the device should NOT reset its outgoing frame counters (both NWK and APS) when emberSetInitialSecurityState() is called. Normally it is advised to reset the frame counter before joining a new network. However, when a device is joining to the same network again (but not using emberRejoinNetwork()), it should keep the NWK and APS frame counters stored in its tokens. NOTE: The application is allowed to dynamically change the behavior via EMBER_EXT_NO_FRAME_COUNTER_RESET field.
EMBER_GET_PRECONFIGURED_KEY_FROM_INSTALL_CODE	This denotes that the device should obtain its pre-configured key from an installation code stored in the manufacturing token. The token contains a value that will be hashed to obtain the actual pre-configured key. If that token is not valid, the call to emberSetInitialSecurityState() will fail.

Definition at line 1877 of file stack/include/ember-types.h

EmberExtendedSecurityBitmask#

EmberExtendedSecurityBitmask

This is the Extended Security Bitmask that controls the use of various extended security features.

Enumerator
EMBER_SECURE_NETWORK_KEY_ROTATION	This denotes that the network key update can only happen if the network key update request is unicast and encrypted i.e. broadcast network key update requests will not be processed if bit 1 is set
EMBER_JOINER_GLOBAL_LINK_KEY	This denotes whether a joiner node (router or end-device) uses a Global Link Key or a Unique Link Key.
EMBER_EXT_NO_FRAME_COUNTER_RESET	This denotes whether the device's outgoing frame counter is allowed to be reset during forming or joining. If the flag is set, the outgoing frame counter is not allowed to be reset. If the flag is not set, the frame counter is allowed to be reset.
EMBER_NWK_LEAVE_WITHOUT_REJOIN_NOT_ALLOWED	This denotes whether a device should discard or accept network leave without rejoin commands.
EMBER_NWK_LEAVE_REQUEST_NOT_ALLOWED	This denotes whether a router node should discard or accept network Leave Commands.

Definition at line 1969 of file stack/include/ember-types.h

EmberCurrentSecurityBitmask#

EmberCurrentSecurityBitmask

This is the Current Security Bitmask that details the use of various security features.

Enumerator
EMBER_STANDARD_SECURITY_MODE_	This denotes that the device is running in a network with ZigBee Standard Security.
EMBER_DISTRIBUTED_TRUST_CENTER_MODE_	This denotes that the device is running in a network without a centralized Trust Center.
EMBER_TRUST_CENTER_GLOBAL_LINK_KEY_	This denotes that the device has a Global Link Key. The Trust Center Link Key is the same across multiple nodes.
EMBER_HAVE_TRUST_CENTER_LINK_KEY	This denotes that the node has a Trust Center Link Key.
EMBER_TRUST_CENTER_USES_HASHED_LINK_KEY_	This denotes that the Trust Center is using a Hashed Link Key.

Definition at line 2083 of file stack/include/ember-types.h

EmberKeyStructBitmask#

EmberKeyStructBitmask

This bitmask describes the presence of fields within the EmberKeyStruct.

Enumerator
EMBER_KEY_HAS_SEQUENCE_NUMBER	This indicates that the key has a sequence number associated with it. (i.e., a Network Key).
EMBER_KEY_HAS_OUTGOING_FRAME_COUNTER	This indicates that the key has an outgoing frame counter and the corresponding value within the EmberKeyStruct has been populated.
EMBER_KEY_HAS_INCOMING_FRAME_COUNTER	This indicates that the key has an incoming frame counter and the corresponding value within the EmberKeyStruct has been populated.
EMBER_KEY_HAS_PARTNER_EUI64	This indicates that the key has an associated Partner EUI64 address and the corresponding value within the EmberKeyStruct has been populated.
EMBER_KEY_IS_AUTHORIZED	This indicates the key is authorized for use in APS data messages. If the key is not authorized for use in APS data messages it has not yet gone through a key agreement protocol, such as CBKE (i.e., ECC).
EMBER_KEY_PARTNER_IS_SLEEPY	This indicates that the partner associated with the link is a sleepy end device. This bit is set automatically if the local device hears a device announce from the partner indicating it is not an 'RX on when idle' device.
EMBER_UNCONFIRMED_TRANSIENT_KEY	This indicates that the transient key which is being added is unconfirmed. This bit is set when we add a transient key while the EmberTcLinkKeyRequestPolicy is EMBER_ALLOW_TC_LINK_KEY_REQUEST_AND_GENERATE_NEW_KEY

Definition at line 2133 of file stack/include/ember-types.h

EmberKeyType#

EmberKeyType

This denotes the type of security key.

Enumerator
EMBER_TRUST_CENTER_LINK_KEY	This denotes that the key is a Trust Center Link Key.
EMBER_CURRENT_NETWORK_KEY	This denotes that the key is the Current Network Key.
EMBER_NEXT_NETWORK_KEY	This denotes that the key is the Next Network Key.
EMBER_APPLICATION_LINK_KEY	This denotes that the key is an Application Link Key.

Definition at line 2179 of file stack/include/ember-types.h

EmberKeyStatus#

EmberKeyStatus

This denotes the status of an attempt to establish a key with another device.

Enumerator
EMBER_KEY_STATUS_NONE
EMBER_APP_LINK_KEY_ESTABLISHED
EMBER_TRUST_CENTER_LINK_KEY_ESTABLISHED
EMBER_KEY_ESTABLISHMENT_TIMEOUT
EMBER_KEY_TABLE_FULL
EMBER_TC_RESPONDED_TO_KEY_REQUEST
EMBER_TC_APP_KEY_SENT_TO_REQUESTER
EMBER_TC_RESPONSE_TO_KEY_REQUEST_FAILED
EMBER_TC_REQUEST_KEY_TYPE_NOT_SUPPORTED
EMBER_TC_NO_LINK_KEY_FOR_REQUESTER
EMBER_TC_REQUESTER_EUI64_UNKNOWN
EMBER_TC_RECEIVED_FIRST_APP_KEY_REQUEST
EMBER_TC_TIMEOUT_WAITING_FOR_SECOND_APP_KEY_REQUEST
EMBER_TC_NON_MATCHING_APP_KEY_REQUEST_RECEIVED
EMBER_TC_FAILED_TO_SEND_APP_KEYS
EMBER_TC_FAILED_TO_STORE_APP_KEY_REQUEST
EMBER_TC_REJECTED_APP_KEY_REQUEST
EMBER_TC_FAILED_TO_GENERATE_NEW_KEY
EMBER_TC_FAILED_TO_SEND_TC_KEY
EMBER_TRUST_CENTER_IS_PRE_R21
EMBER_TC_REQUESTER_VERIFY_KEY_TIMEOUT
EMBER_TC_REQUESTER_VERIFY_KEY_FAILURE
EMBER_TC_REQUESTER_VERIFY_KEY_SUCCESS
EMBER_VERIFY_LINK_KEY_FAILURE
EMBER_VERIFY_LINK_KEY_SUCCESS

Definition at line 2225 of file stack/include/ember-types.h

EmberTcLinkKeyRequestPolicy#

EmberTcLinkKeyRequestPolicy

This enumeration determines whether or not a Trust Center answers trust center link key requests.

Enumerator
EMBER_DENY_TC_LINK_KEY_REQUESTS
EMBER_ALLOW_TC_LINK_KEY_REQUEST_AND_SEND_CURRENT_KEY
EMBER_ALLOW_TC_LINK_KEY_REQUEST_AND_GENERATE_NEW_KEY

Definition at line 2277 of file stack/include/ember-types.h

EmberAppLinkKeyRequestPolicy#

EmberAppLinkKeyRequestPolicy

This enumeration determines whether or not a Trust Center answers app link key requests.

Enumerator
EMBER_DENY_APP_LINK_KEY_REQUESTS
EMBER_ALLOW_APP_LINK_KEY_REQUEST

Definition at line 2297 of file stack/include/ember-types.h

EmberKeySettings#

EmberKeySettings

This is a ZigBee application profile ID that has been assigned to Ember Corporation.

It is used to send for sending messages that have a specific, non-standard, interaction with the Ember stack. Its only current use is for stack counters requests.

Enumerator
EMBER_KEY_PERMISSIONS_NONE
EMBER_KEY_PERMISSIONS_READING_ALLOWED
EMBER_KEY_PERMISSIONS_HASHING_ALLOWED

Definition at line 2427 of file stack/include/ember-types.h

EmberMacPassthroughType#

EmberMacPassthroughType

The types of MAC passthrough messages that an application may receive. This is a bitmask.

Enumerator
EMBER_MAC_PASSTHROUGH_NONE	No MAC passthrough messages.
EMBER_MAC_PASSTHROUGH_SE_INTERPAN	SE InterPAN messages.
EMBER_MAC_PASSTHROUGH_EMBERNET	EmberNet and first generation (v1) standalone bootloader messages.
EMBER_MAC_PASSTHROUGH_EMBERNET_SOURCE	EmberNet messages filtered by their source address.
EMBER_MAC_PASSTHROUGH_APPLICATION	Application-specific passthrough messages.
EMBER_MAC_PASSTHROUGH_CUSTOM	Custom inter-pan filter.

Definition at line 2526 of file stack/include/ember-types.h

emberKeyContents#

uint8_t* emberKeyContents (EmberKeyData * key)

This function allows access to the actual key data bytes of the EmberKeyData structure.

Parameters

N/A

key

A pointer to an EmberKeyData structure.

Returns

uint8_t* Returns a pointer to the first byte of the Key data.

Definition at line 2315 of file stack/include/ember-types.h

emberCertificateContents#

uint8_t* emberCertificateContents (EmberCertificateData * cert)

This function allows access to the actual certificate data bytes of the EmberCertificateData structure.

Parameters

N/A

cert

A pointer to an EmberCertificateData structure.

Returns

uint8_t* Returns a pointer to the first byte of the certificate data.

Definition at line 2328 of file stack/include/ember-types.h

emberPublicKeyContents#

uint8_t* emberPublicKeyContents (EmberPublicKeyData * key)

This function allows access to the actual public key data bytes of the EmberPublicKeyData structure.

Parameters

N/A

key

A pointer to an EmberPublicKeyData structure.

Returns

uint8_t* Returns a pointer to the first byte of the public key data.

Definition at line 2341 of file stack/include/ember-types.h

emberPrivateKeyContents#

uint8_t* emberPrivateKeyContents (EmberPrivateKeyData * key)

This function allows access to the actual private key data bytes of the EmberPrivateKeyData structure.

Parameters

N/A

key

A pointer to an EmberPrivateKeyData structure.

Returns

uint8_t* Returns a pointer to the first byte of the private key data.

Definition at line 2354 of file stack/include/ember-types.h

emberSmacContents#

uint8_t* emberSmacContents (EmberSmacData * key)

This function allows access to the actual SMAC (Secured Message Authentication Code) data of the EmberSmacData structure.

Parameters

N/A key

Definition at line 2364 of file stack/include/ember-types.h

emberSignatureContents#

uint8_t* emberSignatureContents (EmberSignatureData * sig)

This function allows access to the actual ECDSA signature data of the EmberSignatureData structure.

Parameters

N/A sig

Definition at line 2373 of file stack/include/ember-types.h

emberCertificate283k1Contents#

uint8_t* emberCertificate283k1Contents (EmberCertificate283k1Data * cert)

This function allows access to the actual certificate data bytes of the Ember283k1CertificateData structure.

Parameters

N/A

cert

A pointer to an ::Ember283k1CertificateData structure.

Returns

uint8_t* Returns a pointer to the first byte of the certificate data.

Definition at line 2386 of file stack/include/ember-types.h

emberPublicKey283k1Contents#

uint8_t* emberPublicKey283k1Contents (EmberPublicKey283k1Data * key)

This function allows access to the actual public key data bytes of the Ember283k1PublicKeyData structure.

Parameters

N/A

key

A pointer to an Ember283k1PublicKeyData structure.

Returns

uint8_t* Returns a pointer to the first byte of the public key data.

Definition at line 2399 of file stack/include/ember-types.h

emberPrivateKey283k1Contents#

uint8_t* emberPrivateKey283k1Contents (EmberPrivateKey283k1Data * key)

This function allows access to the actual private key data bytes of the Ember283k1PrivateKeyData structure.

Parameters

N/A

key

A pointer to an Ember283k1PrivateKeyData structure.

Returns

uint8_t* Returns a pointer to the first byte of the private key data.

Definition at line 2412 of file stack/include/ember-types.h

ember283k1SignatureContents#

uint8_t* ember283k1SignatureContents (Ember283k1SignatureData * sig)

This function allows access to the actual ECDSA signature data of the Ember283k1SignatureData structure.

Parameters

N/A sig

Definition at line 2421 of file stack/include/ember-types.h

EMBER_PRIVATE_PROFILE_ID#

#define EMBER_PRIVATE_PROFILE_ID

Value:

0xC00Eu

This is a ZigBee application profile ID that has been assigned to Ember Corporation.

It is used to send for sending messages that have a specific, non-standard, interaction with the Ember stack. Its only current use is for stack counters requests.

Definition at line 1745 of file stack/include/ember-types.h

EMBER_PRIVATE_PROFILE_ID_START#

#define EMBER_PRIVATE_PROFILE_ID_START

Value:

0xC00Du

Ember's first private profile ID.

Definition at line 1750 of file stack/include/ember-types.h

EMBER_PRIVATE_PROFILE_ID_END#

#define EMBER_PRIVATE_PROFILE_ID_END

Value:

0xC016u

Ember's last private profile ID.

Definition at line 1755 of file stack/include/ember-types.h

EMBER_REPORT_COUNTERS_REQUEST#

#define EMBER_REPORT_COUNTERS_REQUEST

Value:

0x0003u

The cluster ID used to request that a node respond with a report of its Ember stack counters. See app/util/counters/counters-ota.h.

Definition at line 1760 of file stack/include/ember-types.h

EMBER_REPORT_COUNTERS_RESPONSE#

#define EMBER_REPORT_COUNTERS_RESPONSE

Value:

0x8003u

The cluster ID used to respond to an EMBER_REPORT_COUNTERS_REQUEST.

Definition at line 1763 of file stack/include/ember-types.h

EMBER_REPORT_AND_CLEAR_COUNTERS_REQUEST#

#define EMBER_REPORT_AND_CLEAR_COUNTERS_REQUEST

Value:

0x0004u

The cluster ID used to request that a node respond with a report of its Ember stack counters. The node will also reset its clusters to zero after a successful response. See app/util/counters/counters-ota.h.

Definition at line 1769 of file stack/include/ember-types.h

EMBER_REPORT_AND_CLEAR_COUNTERS_RESPONSE#

#define EMBER_REPORT_AND_CLEAR_COUNTERS_RESPONSE

Value:

0x8004u

The cluster ID used to respond to an EMBER_REPORT_AND_CLEAR_COUNTERS_REQUEST.

Definition at line 1772 of file stack/include/ember-types.h

EMBER_OTA_CERTIFICATE_UPGRADE_CLUSTER#

#define EMBER_OTA_CERTIFICATE_UPGRADE_CLUSTER

Value:

0x0005u

The cluster ID used to send and receive over the air certificate messages. This is used to field upgrade devices with Smart Energy Certificates and other security data.

Definition at line 1778 of file stack/include/ember-types.h

EMBER_STANDARD_SECURITY_MODE#

#define EMBER_STANDARD_SECURITY_MODE

Value:

0x0000

Definition at line 1866 of file stack/include/ember-types.h

EMBER_TRUST_CENTER_NODE_ID#

#define EMBER_TRUST_CENTER_NODE_ID

Value:

0x0000u

The short address of the trust center. This address never changes dynamically.

Definition at line 1871 of file stack/include/ember-types.h

EMBER_NO_TRUST_CENTER_MODE#

#define EMBER_NO_TRUST_CENTER_MODE

Value:

EMBER_DISTRIBUTED_TRUST_CENTER_MODE

This is the legacy name for the Distributed Trust Center Mode.

Definition at line 2024 of file stack/include/ember-types.h

EMBER_GLOBAL_LINK_KEY#

#define EMBER_GLOBAL_LINK_KEY

Value:

EMBER_TRUST_CENTER_GLOBAL_LINK_KEY

This is the legacy name for the Trust Center Global Link Key.

Definition at line 2028 of file stack/include/ember-types.h

EMBER_MFG_SECURITY_CONFIG_MAGIC_NUMBER#

#define EMBER_MFG_SECURITY_CONFIG_MAGIC_NUMBER

Value:

0xCABAD11FUL

This magic number prevents accidentally changing the key settings. The emberSetMfgSecurityConfig() API will return EMBER_INVALID_CALL unless it is passed in.

Definition at line 2449 of file stack/include/ember-types.h

ZDO response status. Documentation#

EmberZdoStatus#

EmberZdoStatus

Enumerator
EMBER_ZDP_SUCCESS
EMBER_ZDP_INVALID_REQUEST_TYPE
EMBER_ZDP_DEVICE_NOT_FOUND
EMBER_ZDP_INVALID_ENDPOINT
EMBER_ZDP_NOT_ACTIVE
EMBER_ZDP_NOT_SUPPORTED
EMBER_ZDP_TIMEOUT
EMBER_ZDP_NO_MATCH
EMBER_ZDP_NO_ENTRY
EMBER_ZDP_NO_DESCRIPTOR
EMBER_ZDP_INSUFFICIENT_SPACE
EMBER_ZDP_NOT_PERMITTED
EMBER_ZDP_TABLE_FULL
EMBER_ZDP_NOT_AUTHORIZED
EMBER_ZDP_DEVICE_BINDING_TABLE_FULL
EMBER_ZDP_INVALID_INDEX
EMBER_NWK_ALREADY_PRESENT
EMBER_NWK_TABLE_FULL
EMBER_NWK_UNKNOWN_DEVICE

Definition at line 2572 of file stack/include/ember-types.h

Network and IEEE Address Request/Response Documentation#

NETWORK_ADDRESS_REQUEST#

#define NETWORK_ADDRESS_REQUEST

Value:

0x0000u

Definition at line 2630 of file stack/include/ember-types.h

NETWORK_ADDRESS_RESPONSE#

#define NETWORK_ADDRESS_RESPONSE

Value:

0x8000u

Definition at line 2631 of file stack/include/ember-types.h

IEEE_ADDRESS_REQUEST#

#define IEEE_ADDRESS_REQUEST

Value:

0x0001u

Definition at line 2632 of file stack/include/ember-types.h

IEEE_ADDRESS_RESPONSE#

#define IEEE_ADDRESS_RESPONSE

Value:

0x8001u

Definition at line 2633 of file stack/include/ember-types.h

Node Descriptor Request/Response Documentation#

NODE_DESCRIPTOR_REQUEST#

#define NODE_DESCRIPTOR_REQUEST

Value:

0x0002u

Definition at line 2661 of file stack/include/ember-types.h

NODE_DESCRIPTOR_RESPONSE#

#define NODE_DESCRIPTOR_RESPONSE

Value:

0x8002u

Definition at line 2662 of file stack/include/ember-types.h

Power Descriptor Request / Response Documentation#

POWER_DESCRIPTOR_REQUEST#

#define POWER_DESCRIPTOR_REQUEST

Value:

0x0003u

Definition at line 2675 of file stack/include/ember-types.h

POWER_DESCRIPTOR_RESPONSE#

#define POWER_DESCRIPTOR_RESPONSE

Value:

0x8003u

Definition at line 2676 of file stack/include/ember-types.h

Simple Descriptor Request / Response Documentation#

SIMPLE_DESCRIPTOR_REQUEST#

#define SIMPLE_DESCRIPTOR_REQUEST

Value:

0x0004u

Definition at line 2692 of file stack/include/ember-types.h

SIMPLE_DESCRIPTOR_RESPONSE#

#define SIMPLE_DESCRIPTOR_RESPONSE

Value:

0x8004u

Definition at line 2693 of file stack/include/ember-types.h

Active Endpoints Request / Response Documentation#

ACTIVE_ENDPOINTS_REQUEST#

#define ACTIVE_ENDPOINTS_REQUEST

Value:

0x0005u

Definition at line 2704 of file stack/include/ember-types.h

ACTIVE_ENDPOINTS_RESPONSE#

#define ACTIVE_ENDPOINTS_RESPONSE

Value:

0x8005u

Definition at line 2705 of file stack/include/ember-types.h

Match Descriptors Request / Response Documentation#

MATCH_DESCRIPTORS_REQUEST#

#define MATCH_DESCRIPTORS_REQUEST

Value:

0x0006u

Definition at line 2719 of file stack/include/ember-types.h

MATCH_DESCRIPTORS_RESPONSE#

#define MATCH_DESCRIPTORS_RESPONSE

Value:

0x8006u

Definition at line 2720 of file stack/include/ember-types.h

Discovery Cache Request / Response Documentation#

DISCOVERY_CACHE_REQUEST#

#define DISCOVERY_CACHE_REQUEST

Value:

0x0012u

Definition at line 2732 of file stack/include/ember-types.h

DISCOVERY_CACHE_RESPONSE#

#define DISCOVERY_CACHE_RESPONSE

Value:

0x8012u

Definition at line 2733 of file stack/include/ember-types.h

End Device Announce and End Device Announce Response Documentation#

END_DEVICE_ANNOUNCE#

#define END_DEVICE_ANNOUNCE

Value:

0x0013u

Definition at line 2744 of file stack/include/ember-types.h

END_DEVICE_ANNOUNCE_RESPONSE#

#define END_DEVICE_ANNOUNCE_RESPONSE

Value:

0x8013u

Definition at line 2745 of file stack/include/ember-types.h

System Server Discovery Request / Response Documentation#

SYSTEM_SERVER_DISCOVERY_REQUEST#

#define SYSTEM_SERVER_DISCOVERY_REQUEST

Value:

0x0015u

Definition at line 2759 of file stack/include/ember-types.h

SYSTEM_SERVER_DISCOVERY_RESPONSE#

#define SYSTEM_SERVER_DISCOVERY_RESPONSE

Value:

0x8015u

Definition at line 2760 of file stack/include/ember-types.h

Parent Announce and Parent Announce Response Documentation#

PARENT_ANNOUNCE#

#define PARENT_ANNOUNCE

Value:

0x001Fu

Definition at line 2775 of file stack/include/ember-types.h

PARENT_ANNOUNCE_RESPONSE#

#define PARENT_ANNOUNCE_RESPONSE

Value:

0x801Fu

Definition at line 2776 of file stack/include/ember-types.h

ZDO server mask bits Documentation#

EmberZdoServerMask#

EmberZdoServerMask

Enumerator
EMBER_ZDP_PRIMARY_TRUST_CENTER
EMBER_ZDP_SECONDARY_TRUST_CENTER
EMBER_ZDP_PRIMARY_BINDING_TABLE_CACHE
EMBER_ZDP_SECONDARY_BINDING_TABLE_CACHE
EMBER_ZDP_PRIMARY_DISCOVERY_CACHE
EMBER_ZDP_SECONDARY_DISCOVERY_CACHE
EMBER_ZDP_NETWORK_MANAGER

Definition at line 2784 of file stack/include/ember-types.h

Find Node Cache Request / Response Documentation#

FIND_NODE_CACHE_REQUEST#

#define FIND_NODE_CACHE_REQUEST

Value:

0x001Cu

Definition at line 2813 of file stack/include/ember-types.h

FIND_NODE_CACHE_RESPONSE#

#define FIND_NODE_CACHE_RESPONSE

Value:

0x801Cu

Definition at line 2814 of file stack/include/ember-types.h

End Device Bind Request / Response Documentation#

END_DEVICE_BIND_REQUEST#

#define END_DEVICE_BIND_REQUEST

Value:

0x0020u

Definition at line 2827 of file stack/include/ember-types.h

END_DEVICE_BIND_RESPONSE#

#define END_DEVICE_BIND_RESPONSE

Value:

0x8020u

Definition at line 2828 of file stack/include/ember-types.h

Binding types and Request / Response Documentation#

UNICAST_BINDING#

#define UNICAST_BINDING

Value:

0x03u

Definition at line 2848 of file stack/include/ember-types.h

UNICAST_MANY_TO_ONE_BINDING#

#define UNICAST_MANY_TO_ONE_BINDING

Value:

0x83u

Definition at line 2849 of file stack/include/ember-types.h

MULTICAST_BINDING#

#define MULTICAST_BINDING

Value:

0x01u

Definition at line 2850 of file stack/include/ember-types.h

BIND_REQUEST#

#define BIND_REQUEST

Value:

0x0021u

Definition at line 2852 of file stack/include/ember-types.h

BIND_RESPONSE#

#define BIND_RESPONSE

Value:

0x8021u

Definition at line 2853 of file stack/include/ember-types.h

UNBIND_REQUEST#

#define UNBIND_REQUEST

Value:

0x0022u

Definition at line 2854 of file stack/include/ember-types.h

UNBIND_RESPONSE#

#define UNBIND_RESPONSE

Value:

0x8022u

Definition at line 2855 of file stack/include/ember-types.h

LQI Table Request / Response Documentation#

LQI_TABLE_REQUEST#

#define LQI_TABLE_REQUEST

Value:

0x0031u

Definition at line 2905 of file stack/include/ember-types.h

LQI_TABLE_RESPONSE#

#define LQI_TABLE_RESPONSE

Value:

0x8031u

Definition at line 2906 of file stack/include/ember-types.h

Routing Table Request / Response Documentation#

ROUTING_TABLE_REQUEST#

#define ROUTING_TABLE_REQUEST

Value:

0x0032u

Definition at line 2941 of file stack/include/ember-types.h

ROUTING_TABLE_RESPONSE#

#define ROUTING_TABLE_RESPONSE

Value:

0x8032u

Definition at line 2942 of file stack/include/ember-types.h

Binding Table Request / Response Documentation#

BINDING_TABLE_REQUEST#

#define BINDING_TABLE_REQUEST

Value:

0x0033u

Definition at line 2963 of file stack/include/ember-types.h

BINDING_TABLE_RESPONSE#

#define BINDING_TABLE_RESPONSE

Value:

0x8033u

Definition at line 2964 of file stack/include/ember-types.h

Leave Request / Response Documentation#

LEAVE_REQUEST#

#define LEAVE_REQUEST

Value:

0x0034u

Definition at line 2977 of file stack/include/ember-types.h

LEAVE_RESPONSE#

#define LEAVE_RESPONSE

Value:

0x8034u

Definition at line 2978 of file stack/include/ember-types.h

LEAVE_REQUEST_REMOVE_CHILDREN_FLAG#

#define LEAVE_REQUEST_REMOVE_CHILDREN_FLAG

Value:

0x40u

Definition at line 2980 of file stack/include/ember-types.h

LEAVE_REQUEST_REJOIN_FLAG#

#define LEAVE_REQUEST_REJOIN_FLAG

Value:

0x80u

Definition at line 2981 of file stack/include/ember-types.h

Permit Joining Request / Response Documentation#

PERMIT_JOINING_REQUEST#

#define PERMIT_JOINING_REQUEST

Value:

0x0036u

Definition at line 2992 of file stack/include/ember-types.h

PERMIT_JOINING_RESPONSE#

#define PERMIT_JOINING_RESPONSE

Value:

0x8036u

Definition at line 2993 of file stack/include/ember-types.h

Network Update Request / Response Documentation#

NWK_UPDATE_REQUEST#

#define NWK_UPDATE_REQUEST

Value:

0x0038u

Definition at line 3021 of file stack/include/ember-types.h

NWK_UPDATE_RESPONSE#

#define NWK_UPDATE_RESPONSE

Value:

0x8038u

Definition at line 3022 of file stack/include/ember-types.h

NWK_UPDATE_ENHANCED_REQUEST#

#define NWK_UPDATE_ENHANCED_REQUEST

Value:

0x0039u

Definition at line 3024 of file stack/include/ember-types.h

NWK_UPDATE_ENHANCED_RESPONSE#

#define NWK_UPDATE_ENHANCED_RESPONSE

Value:

0x8039u

Definition at line 3025 of file stack/include/ember-types.h

NWK_UPDATE_IEEE_JOINING_LIST_REQUEST#

#define NWK_UPDATE_IEEE_JOINING_LIST_REQUEST

Value:

0x003Au

Definition at line 3027 of file stack/include/ember-types.h

NWK_UPDATE_IEEE_JOINING_LIST_REPONSE#

#define NWK_UPDATE_IEEE_JOINING_LIST_REPONSE

Value:

0x803Au

Definition at line 3028 of file stack/include/ember-types.h

NWK_UNSOLICITED_ENHANCED_UPDATE_NOTIFY#

#define NWK_UNSOLICITED_ENHANCED_UPDATE_NOTIFY

Value:

0x803Bu

Definition at line 3030 of file stack/include/ember-types.h

Unsupported Documentation#

COMPLEX_DESCRIPTOR_REQUEST#

#define COMPLEX_DESCRIPTOR_REQUEST

Value:

0x0010u

Definition at line 3037 of file stack/include/ember-types.h

COMPLEX_DESCRIPTOR_RESPONSE#

#define COMPLEX_DESCRIPTOR_RESPONSE

Value:

0x8010u

Definition at line 3038 of file stack/include/ember-types.h

USER_DESCRIPTOR_REQUEST#

#define USER_DESCRIPTOR_REQUEST

Value:

0x0011u

Definition at line 3039 of file stack/include/ember-types.h

USER_DESCRIPTOR_RESPONSE#

#define USER_DESCRIPTOR_RESPONSE

Value:

0x8011u

Definition at line 3040 of file stack/include/ember-types.h

DISCOVERY_REGISTER_REQUEST#

#define DISCOVERY_REGISTER_REQUEST

Value:

0x0012u

Definition at line 3041 of file stack/include/ember-types.h

DISCOVERY_REGISTER_RESPONSE#

#define DISCOVERY_REGISTER_RESPONSE

Value:

0x8012u

Definition at line 3042 of file stack/include/ember-types.h

USER_DESCRIPTOR_SET#

#define USER_DESCRIPTOR_SET

Value:

0x0014u

Definition at line 3043 of file stack/include/ember-types.h

USER_DESCRIPTOR_CONFIRM#

#define USER_DESCRIPTOR_CONFIRM

Value:

0x8014u

Definition at line 3044 of file stack/include/ember-types.h

NETWORK_DISCOVERY_REQUEST#

#define NETWORK_DISCOVERY_REQUEST

Value:

0x0030u

Definition at line 3045 of file stack/include/ember-types.h

NETWORK_DISCOVERY_RESPONSE#

#define NETWORK_DISCOVERY_RESPONSE

Value:

0x8030u

Definition at line 3046 of file stack/include/ember-types.h

DIRECT_JOIN_REQUEST#

#define DIRECT_JOIN_REQUEST

Value:

0x0035u

Definition at line 3047 of file stack/include/ember-types.h

DIRECT_JOIN_RESPONSE#

#define DIRECT_JOIN_RESPONSE

Value:

0x8035u

Definition at line 3048 of file stack/include/ember-types.h

CLUSTER_ID_RESPONSE_MINIMUM#

#define CLUSTER_ID_RESPONSE_MINIMUM

Value:

0x8000u

Definition at line 3050 of file stack/include/ember-types.h

ZDO configuration flags. Documentation#

EmberZdoConfigurationFlags#

EmberZdoConfigurationFlags

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Enumerator
EMBER_APP_RECEIVES_SUPPORTED_ZDO_REQUESTS
EMBER_APP_HANDLES_UNSUPPORTED_ZDO_REQUESTS
EMBER_APP_HANDLES_ZDO_ENDPOINT_REQUESTS
EMBER_APP_HANDLES_ZDO_BINDING_REQUESTS

Definition at line 3066 of file stack/include/ember-types.h

EmberMultiPhyNwkConfig#

EmberMultiPhyNwkConfig

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Enumerator
EMBER_MULTI_PHY_ROUTERS_ALLOWED
EMBER_MULTI_PHY_BROADCASTS_ENABLED
EMBER_MULTI_PHY_DISABLED

Definition at line 3094 of file stack/include/ember-types.h

@0#

@0

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Enumerator
PRIORITIZE_BEACONS_BASED_ON_PARENT_CLASSIFICATION
PRIORITIZE_BEACONS_BASED_ON_TC_CONNECTVITY
TC_CONNECTIVITY
LONG_UPTIME
BAD_PARENT_CONNECTIVITY
EMBER_OUTGOING_MESSAGES	Messages are waiting for transmission.
EMBER_INCOMING_MESSAGES	One or more incoming messages are being processed.
EMBER_RADIO_IS_ON	The radio is currently powered on. On sleepy devices, the radio is turned off when not in use. On non-sleepy devices (EMBER_COORDINATOR, EMBER_ROUTER, or EMBER_END_DEVICE), the radio is always on.
EMBER_TRANSPORT_ACTIVE	The transport layer has messages awaiting an ACK.
EMBER_APS_LAYER_ACTIVE	The ZigBee APS layer has messages awaiting an ACK.
EMBER_ASSOCIATING	The node is currently trying to associate with a ZigBee PRO network.
EMBER_ZLL_TOUCH_LINKING	The node is currently touch linking.
EMBER_NETWORK_TIMEOUT_REQUEST	Network Timeout Request Event.
EMBER_SEND_ORPHAN_NOTIFICATION	Sending Orphan Notification Event.
EMBER_MAC_DATA_POLL_SUPER_RETRY	MAC Data Poll Super Retry Event .

Definition at line 3137 of file stack/include/ember-types.h

EmberEntropySource#

EmberEntropySource

Defines the entropy source used by the stack.

Enumerator
EMBER_ENTROPY_SOURCE_ERROR
EMBER_ENTROPY_SOURCE_RADIO
EMBER_ENTROPY_SOURCE_MBEDTLS_TRNG
EMBER_ENTROPY_SOURCE_MBEDTLS

Definition at line 3154 of file stack/include/ember-types.h

@1#

@1

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Enumerator
EMBER_POLL_TIMEOUT_10_SECONDS
EMBER_POLL_TIMEOUT_2_MINUTES
EMBER_POLL_TIMEOUT_4_MINUTES
EMBER_POLL_TIMEOUT_8_MINUTES
EMBER_POLL_TIMEOUT_16_MINUTES
EMBER_POLL_TIMEOUT_32_MINUTES
EMBER_POLL_TIMEOUT_64_MINUTES
EMBER_POLL_TIMEOUT_128_MINUTES
EMBER_POLL_TIMEOUT_256_MINUTES
EMBER_POLL_TIMEOUT_512_MINUTES
EMBER_POLL_TIMEOUT_1024_MINUTES
EMBER_POLL_TIMEOUT_2048_MINUTES
EMBER_POLL_TIMEOUT_4096_MINUTES
EMBER_POLL_TIMEOUT_8192_MINUTES
EMBER_POLL_TIMEOUT_16384_MINUTES

Definition at line 3166 of file stack/include/ember-types.h

EmberTcApsEncryptMode#

EmberTcApsEncryptMode

Enumerator
TC_APS_ENCRYPT_DEFAULT	Default: don't encrypt broadcasts, encrypt unicasts
TC_APS_ENCRYPT_ENABLE	Encrypt both broadcasts and unicasts
TC_APS_ENCRYPT_DISABLE	Do not encrypt broadcasts and unicasts

Definition at line 3190 of file stack/include/ember-types.h

EmberRadioPowerMode#

typedef uint8_t EmberRadioPowerMode

Radio power mode.

Definition at line 3130 of file stack/include/ember-types.h

WEAK_TEST#

#define WEAK_TEST

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Definition at line 3090 of file stack/include/ember-types.h

EMBER_MAX_MAC_ONLY_COUNTERS#

#define EMBER_MAX_MAC_ONLY_COUNTERS

Value:

33u

Defines the maximum number of counters that are specified as reporting either on 2.4 GHz or Sub-GHz.

Definition at line 3109 of file stack/include/ember-types.h

EMBER_MAX_NUM_PHYS#

#define EMBER_MAX_NUM_PHYS

Value:

2u

Defines the maximum number of PHYs supported.

Definition at line 3115 of file stack/include/ember-types.h

PHY_INDEX_NATIVE#

#define PHY_INDEX_NATIVE

Value:

0u

PHY index for 2.4 GHz radio interface, valid for simultaneous multi radio network.

Definition at line 3120 of file stack/include/ember-types.h

PHY_INDEX_PRO2PLUS#

#define PHY_INDEX_PRO2PLUS

Value:

1u

PHY index for Sub-GHz radio interface, valid for simultaneous multi radio network.

Definition at line 3125 of file stack/include/ember-types.h

Enumeration Documentation#

EmberNodeType#

EmberNodeType

Defines the possible types of nodes and the roles that a node might play in a network.

Enumerator
EMBER_UNKNOWN_DEVICE	The device is not joined.
EMBER_COORDINATOR	Will relay messages and can act as a parent to other nodes.
EMBER_ROUTER	Will relay messages and can act as a parent to other nodes.
EMBER_END_DEVICE	Communicates only with its parent and will not relay messages.
EMBER_SLEEPY_END_DEVICE	An end device whose radio can be turned off to save power. The application must call emberPollForData() to receive messages.
EMBER_WIREFREE_INITIATOR_DEVICE	Sleepy end device which transmits with wake up frames (CSL).
EMBER_WIREFREE_TARGET_DEVICE	Sleepy end device which duty cycles the radio Rx (CSL).

Definition at line 545 of file stack/include/ember-types.h

EmberEndDeviceConfiguration#

EmberEndDeviceConfiguration

The configuration advertised by the end device to the parent when joining/rejoining.

Enumerator
EMBER_END_DEVICE_CONFIG_NONE
EMBER_END_DEVICE_CONFIG_PERSIST_DATA_ON_PARENT

Definition at line 573 of file stack/include/ember-types.h

EmberNetworkInitBitmask#

EmberNetworkInitBitmask

Defines the options that should be used when initializing the node's network configuration.

Enumerator
EMBER_NETWORK_INIT_NO_OPTIONS
EMBER_NETWORK_INIT_PARENT_INFO_IN_TOKEN	The Parent Node ID and EUI64 are stored in a token. This prevents the need to perform an Orphan scan on startup.
EMBER_NETWORK_INIT_END_DEVICE_REJOIN_ON_REBOOT	Z3 compliant end devices on a network must send a rejoin request on reboot.

Definition at line 600 of file stack/include/ember-types.h

EmberApsRejoinMode#

EmberApsRejoinMode

Options to allow/disallow rejoins using the default link key.

Enumerator
NO_REJOIN
REJOIN_ANY_LINK_KEY
REJOIN_NON_DEFAULT_LINK_KEY

Definition at line 669 of file stack/include/ember-types.h

EmberApsOption#

EmberApsOption

Options to use when sending a message.

The discover-route, APS-retry, and APS-indirect options may be used together. Poll response cannot be combined with any other options.

Enumerator
EMBER_APS_OPTION_NONE	No options.
EMBER_APS_OPTION_DSA_SIGN	This signs the application layer message body (APS Frame not included) and appends the ECDSA signature to the end of the message, which is needed by Smart Energy applications and requires the CBKE and ECC libraries. The emberDsaSignHandler() function is called after DSA signing is complete but before the message has been sent by the APS layer. Note that when passing a buffer to the stack for DSA signing, the final byte in the buffer has a special significance as an indicator of how many leading bytes should be ignored for signature purposes. See the API documentation of emberDsaSign() or the dsaSign EZSP command for more details about this requirement.
EMBER_APS_OPTION_ENCRYPTION	Send the message using APS Encryption using the Link Key shared with the destination node to encrypt the data at the APS Level.
EMBER_APS_OPTION_RETRY	Resend the message using the APS retry mechanism. This option and the enable route discovery option must be enabled for an existing route to be repaired automatically.
EMBER_APS_OPTION_ENABLE_ROUTE_DISCOVERY	Send the message with the NWK 'enable route discovery' flag, which causes a route discovery to be initiated if no route to the destination is known. Note that in the mesh stack, this option and the APS retry option must be enabled an existing route to be repaired automatically.
EMBER_APS_OPTION_FORCE_ROUTE_DISCOVERY	Send the message with the NWK 'force route discovery' flag, which causes a route discovery to be initiated even if one is known.
EMBER_APS_OPTION_SOURCE_EUI64	Include the source EUI64 in the network frame.
EMBER_APS_OPTION_DESTINATION_EUI64	Include the destination EUI64 in the network frame.
EMBER_APS_OPTION_ENABLE_ADDRESS_DISCOVERY	Send a ZDO request to discover the node ID of the destination if it is not already known.
EMBER_APS_OPTION_POLL_RESPONSE	This message is being sent in response to a call to emberPollHandler(). It causes the message to be sent immediately instead of being queued up until the next poll from the (end device) destination.
EMBER_APS_OPTION_ZDO_RESPONSE_REQUIRED	This incoming message is a valid ZDO request and the application is responsible for sending a ZDO response. This flag is used only within emberIncomingMessageHandler() when EMBER_APPLICATION_RECEIVES_UNSUPPORTED_ZDO_REQUESTS is defined.
EMBER_APS_OPTION_FRAGMENT	This message is part of a fragmented message. This option may only be set for unicasts. The groupId field gives the index of this fragment in the low-order byte. If the low-order byte is zero this is the first fragment and the high-order byte contains the number of fragments in the message.

Definition at line 687 of file stack/include/ember-types.h

EmberIncomingMessageType#

EmberIncomingMessageType

Defines the possible incoming message types.

Enumerator
EMBER_INCOMING_UNICAST	Unicast.
EMBER_INCOMING_UNICAST_REPLY	Unicast reply.
EMBER_INCOMING_MULTICAST	Multicast.
EMBER_INCOMING_MULTICAST_LOOPBACK	Multicast sent by the local device.
EMBER_INCOMING_BROADCAST	Broadcast.
EMBER_INCOMING_BROADCAST_LOOPBACK	Broadcast sent by the local device.

Definition at line 758 of file stack/include/ember-types.h

EmberOutgoingMessageType#

EmberOutgoingMessageType

Defines the possible outgoing message types.

Enumerator
EMBER_OUTGOING_DIRECT	Unicast sent directly to an EmberNodeId.
EMBER_OUTGOING_VIA_ADDRESS_TABLE	Unicast sent using an entry in the address table.
EMBER_OUTGOING_VIA_BINDING	Unicast sent using an entry in the binding table.
EMBER_OUTGOING_MULTICAST	Multicast message. This value is passed to emberMessageSentHandler() only. It may not be passed to emberSendUnicast().
EMBER_OUTGOING_MULTICAST_WITH_ALIAS	An aliased multicast message. This value is passed to emberMessageSentHandler() only. It may not be passed to emberSendUnicast().
EMBER_OUTGOING_BROADCAST_WITH_ALIAS	An aliased Broadcast message. This value is passed to emberMessageSentHandler() only. It may not be passed to emberSendUnicast().
EMBER_OUTGOING_BROADCAST	A broadcast message. This value is passed to emberMessageSentHandler() only. It may not be passed to emberSendUnicast().

Definition at line 782 of file stack/include/ember-types.h

EmberZigbeeCommandType#

EmberZigbeeCommandType

A type of command received by the stack.

This enumeration indicates which protocol layer in the Ember stack an incoming command was meant for, or from which protocol layer an outgoing command is being sent.

Enumerator
EMBER_ZIGBEE_COMMAND_TYPE_RAW_MAC	Describes an 802.15.4 raw MAC message, unprocessed by the stack.
EMBER_ZIGBEE_COMMAND_TYPE_MAC_COMMAND	Describes an 802.15.4 MAC layer command.
EMBER_ZIGBEE_COMMAND_TYPE_NWK	Describes a ZigBee Network layer command.
EMBER_ZIGBEE_COMMAND_TYPE_APS	Describes a ZigBee Application Support layer command.
EMBER_ZIGBEE_COMMAND_TYPE_ZDO	Describes a ZigBee Device Object command.
EMBER_ZIGBEE_COMMAND_TYPE_ZCL	Describes a ZigBee Cluster Library command.
EMBER_ZIGBEE_COMMAND_TYPE_BEACON	Not a MAC command, but enumerated here for simplicity.

Definition at line 816 of file stack/include/ember-types.h

EmberPacketAction#

EmberPacketAction

indication of the action taken on a packet

Enumerator
EMBER_DROP_PACKET
EMBER_ACCEPT_PACKET
EMBER_MANGLE_PACKET
EMBER_ACCEPT_PACKET_OVERRIDE_SECURITY	This action allows unencrypted packets to pass through the stack. We only support this action in the network layer for now. WARNING: Using this packet handler action may have serious security implications
EMBER_ACCEPT_PACKET_SKIP_NWK_CRYPTO	This action allows unencrypted incoming packets to skip NWK decryption as well as outgoing packets to skip NWK encryption irrespective of the encryption flag in the NWK header. We only support this action in the network layer for now.

Definition at line 840 of file stack/include/ember-types.h

EmberZigbeePacketType#

EmberZigbeePacketType

A type of packet received by the stack.

This enum provides a way to indicate which protocol layer in the Ember stack an incoming packet is meant for, or from which protocol layer an outgoing command is being sent from.

Enumerator
EMBER_ZIGBEE_PACKET_TYPE_RAW_MAC	Describes an 802.15.4 raw MAC message, unprocessed by the stack.
EMBER_ZIGBEE_PACKET_TYPE_MAC_COMMAND	Describes an 802.15.4 MAC layer command.
EMBER_ZIGBEE_PACKET_TYPE_NWK_DATA	Describes a ZigBee Network layer data message.
EMBER_ZIGBEE_PACKET_TYPE_NWK_COMMAND	Describes a ZigBee Network layer command.
EMBER_ZIGBEE_PACKET_TYPE_APS_DATA	Describes a ZigBee Application Support layer data message.
EMBER_ZIGBEE_PACKET_TYPE_APS_COMMAND	Describes a ZigBee Application Support layer command.
EMBER_ZIGBEE_PACKET_TYPE_ZDO	Describes a ZigBee Device Object command.
EMBER_ZIGBEE_PACKET_TYPE_ZCL	Describes a ZigBee Cluster Library command.
EMBER_ZIGBEE_PACKET_TYPE_BEACON	Distinguishing between raw MAC and beacons for simplicity
EMBER_ZIGBEE_PACKET_TYPE_INTERPAN	Describes a ZigBee Light Link message.
EMBER_ZIGBEE_PACKET_TYPE_NWK_DATA_PRE_DECRYPTION	Describes a ZigBee Network layer data message prior to (potential) decryption.
EMBER_ZIGBEE_PACKET_TYPE_NWK_COMMAND_PRE_DECRYPTION	Describes a ZigBee Network layer command prior to (potential) decryption.

Definition at line 869 of file stack/include/ember-types.h

EmberNetworkStatus#

EmberNetworkStatus

Defines the possible join states for a node.

Enumerator
EMBER_NO_NETWORK	The node is not associated with a network in any way.
EMBER_JOINING_NETWORK	The node is currently attempting to join a network.
EMBER_JOINED_NETWORK	The node is joined to a network.
EMBER_JOINED_NETWORK_NO_PARENT	The node is an end device joined to a network but its parent is not responding.
EMBER_JOINED_NETWORK_WF_INITIATOR	The node is an Wire free initiator
EMBER_JOINED_NETWORK_WF_TARGET	The node is an Wire free target
EMBER_LEAVING_NETWORK	The node is in the process of leaving its current network.

Definition at line 905 of file stack/include/ember-types.h

EmberNetworkScanType#

EmberNetworkScanType

Type for a network scan.

Enumerator
EMBER_ENERGY_SCAN	An energy scan scans each channel for its RSSI value.
EMBER_ACTIVE_SCAN	An active scan scans each channel for available networks. Use this scan type during network-steering to filter for beacons with available child capacity. The network found callback emberAfNetworkFoundCallback fires for all received beacons, while only beacons matching the capacity criteria and therefore viable for joining are cached
EMBER_START_RADIO_OFF_SCAN	A fake scan that is used to turn off the radio.
EMBER_STACK_GP_CHANNEL_DELIVERY_SCAN	A green power channel delivery scan.
EMBER_ACTIVE_SCAN_ROUTER	An active scan scans each channel for available networks. Use this scan type during network-steering to filter for and cache beacons with available router capacity - Note that this scan type temporarily sets nodeType to EMBER_ROUTER for the duration of the scan process. The network found callback emberAfNetworkFoundCallback fires for all received beacons, while only beacons matching the capacity criteria and therefore viable for joining are cached
EMBER_LAST_SCAN_TYPE

Definition at line 942 of file stack/include/ember-types.h

EmberBindingType#

EmberBindingType

Defines binding types.

Enumerator
EMBER_UNUSED_BINDING	A binding that is currently not in use.
EMBER_UNICAST_BINDING	A unicast binding whose 64-bit identifier is the destination EUI64.
EMBER_MANY_TO_ONE_BINDING	A unicast binding whose 64-bit identifier is the many-to-one destination EUI64. Route discovery should be disabled when sending unicasts via many-to-one bindings.
EMBER_MULTICAST_BINDING	A multicast binding whose 64-bit identifier is the group address. This binding can be used to send messages to the group and to receive messages sent to the group.

Definition at line 970 of file stack/include/ember-types.h

EmberKeepAliveMode#

EmberKeepAliveMode

Type of Ember keep alive method defining the keep alive message type that a parent accepts to prevent child aging. This is configured in a parent router and communicated and stored in an end-device.

EMBER_KEEP_ALIVE_SUPPORT_UNKNOWN which is initialized at end-device boot time, means parent's keep alive mechanism is unknown to end-device.

EMBER_MAC_DATA_POLL_KEEP_ALIVE means that the parent does not need explicit keep alive messages and will use incoming mac data polls as a sign that a child should not be aged out.

EMBER_END_DEVICE_TIMEOUT_KEEP_ALIVE means that the parent needs explicit keep alive messages (net work timeout requests) to keep the child in its child table.

EMBER_KEEP_ALIVE_SUPPORT_ALL basically maps to EMBER_MAC_DATA_POLL_KEEP_ALIVE as the preferred approach between the two.

Enumerator
EMBER_KEEP_ALIVE_SUPPORT_UNKNOWN
EMBER_MAC_DATA_POLL_KEEP_ALIVE
EMBER_END_DEVICE_TIMEOUT_KEEP_ALIVE
EMBER_KEEP_ALIVE_SUPPORT_ALL

Definition at line 3225 of file stack/include/ember-types.h

EmberSourceRouteDiscoveryMode#

EmberSourceRouteDiscoveryMode

Types of source route discovery modes used by the concentrator.

EMBER_SOURCE_ROUTE_DISCOVERY_OFF no source route discovery is scheduled EMBER_SOURCE_ROUTE_DISCOVERY_ON source routes discovery is scheduled, and it is triggered periodically EMBER_SOURCE_ROUTE_DISCOVERY_RESCHEDULE source routes discoveries are re-scheduled to be sent once immediately and then triggered periodically

Enumerator
EMBER_SOURCE_ROUTE_DISCOVERY_OFF	off
EMBER_SOURCE_ROUTE_DISCOVERY_ON	on
EMBER_SOURCE_ROUTE_DISCOVERY_RESCHEDULE	reschedule

Definition at line 3246 of file stack/include/ember-types.h

EmberTransmitPriority#

EmberTransmitPriority

Packet transmit priorities in terms of getting into the MAC queue.

EMBER_MAC_TRANSMIT_PRIORITY_HIGH High priority headers go on the front of the queue. EMBER_MAC_TRANSMIT_PRIORITY_NORMAL Normal priority headers go on the back of the queue. EMBER_MAC_TRANSMIT_PRIORITY_SCAN_OKAY Normally, only beacon requests and orphan notifications can be sent during a scan. They are submitted with SCAN_OKAY and go on the front of the queue. Other packets could be submitted with this priority, but it is not recommended.

Enumerator
EMBER_MAC_TRANSMIT_PRIORITY_HIGH
EMBER_MAC_TRANSMIT_PRIORITY_NORMAL
EMBER_MAC_TRANSMIT_PRIORITY_SCAN_OKAY

Definition at line 3276 of file stack/include/ember-types.h

sl_zigbee_route_record_policy_type_t#

sl_zigbee_route_record_policy_type_t

Policies for sending a route record to the concentrator.

When sending a unicast to a concentrator, the message may be preceded by a route record packet depending on the type of concentrator and the route record policy

Enumerator
ROUTE_RECORD_POLICY_ACK_BY_SOURCE_ROUTED_MESSAGE	ROUTE_RECORD_POLICY_ACK_BY_SOURCE_ROUTED_MESSAGE is the default policy A low RAM concentrator will be sent a route record ahead of any unicast A high RAM concentrator will be sent a route record ahead of any unicast until a source routed unicast is received from it.
ROUTE_RECORD_POLICY_DONT_SEND	ROUTE_RECORD_POLICY_DONT_SEND policy means that the local node never sends a route record message (Note: Non-compliant)
ROUTE_RECORD_POLICY_NO_ACK_REQUIRED	ROUTE_RECORD_POLICY_NO_ACK_REQUIRED A low RAM concentrator will be sent a route record ahead of any unicast A high RAM concentrator will be sent a route record ahead of any unicast (Note: Non-compliant)

Definition at line 3295 of file stack/include/ember-types.h

Macro Definition Documentation#

EMBER_MIN_BROADCAST_ADDRESS#

#define EMBER_MIN_BROADCAST_ADDRESS

Value:

0xFFF8u

Definition at line 532 of file stack/include/ember-types.h

emberIsZigbeeBroadcastAddress#

#define emberIsZigbeeBroadcastAddress

Value:

(address)

Returns true if nodeId (short address) is a broadcast address.

Definition at line 537 of file stack/include/ember-types.h