Radio#

sl_si91x_transmit_test_start#

sl_status_t sl_si91x_transmit_test_start (const sl_si91x_request_tx_test_info_t * tx_test_info)

Start the transmit test.

This function starts the transmit test using the provided configuration.

This is a blocking API.

This API is relevant in PER mode

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.
  

Note

• Before starting Continuous Wave mode, user must start Continuous mode with power and channel values that are intended to be used in Continuous Wave mode i.e.
  

  • Start Continuous mode with intended power value and channel values - Pass any valid values for rate and length.

  • Stop Continuous mode

  • Start Continuous Wave mode

• If user wants to switch continuous wave mode, first need to stop the per mode and again need to give continous wave mode which user wants to switch.

sl_si91x_transmit_test_stop#

sl_status_t sl_si91x_transmit_test_stop (void )

Stop the transmit test.

This function stops the ongoing transmit test on the Si91x device.

This is a blocking API.

This API is relevant in PER mode.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.
  

Note

• User should configure a minimum delay (approx. 10 milliseconds) before and after sl_si91x_transmit_test_start API to observe a stable output at requested dBm level.

sl_si91x_frequency_offset#

sl_status_t sl_si91x_frequency_offset (const sl_si91x_freq_offset_t * frequency_calibration)

Provide feedback of frequency error in KHz.

This function provides feedback of the frequency error in KHz. The frequency error is specified using the sl_si91x_freq_offset_t structure.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

sl_si91x_set_device_region#

sl_status_t sl_si91x_set_device_region (sl_si91x_operation_mode_t operation_mode, sl_si91x_band_mode_t band, sl_si91x_region_code_t region_code)

Set the device region.

This function sets the operational region of the Si91x device. The region is specified using the sl_si91x_region_code_t enumeration.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

Note

• In FCC-certifed module the behavior is as follows

  1. Region configuration is not supported and if triggered will return error SL_STATUS_SI91X_FEATURE_NOT_AVAILABLE.

  2. STA mode channels 1 to 11 are actively scanned and 12,13,14 are passively scanned.

  3. AP mode and Concurrent mode supports only 1 to 11 channels.

  4. The AP will not broadcast the Country Information Element (IE).

sl_si91x_calibration_write#

sl_status_t sl_si91x_calibration_write (sl_si91x_calibration_write_t calib_write)

Command the firmware to update the existing Flash/EFuse calibration data.

This function commands the firmware to update the existing Flash/EFuse calibration data using the provided calibration configuration.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init, sl_si91x_transmit_test_start, and sl_si91x_frequency_offset should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

Note

• Executing this API will overwrite calibration values in certified modules. In FCC-certified modules, this API will trigger an error SL_STATUS_SI91X_FEATURE_NOT_AVAILABLE if used, except when in SL_SI91X_TRANSMIT_TEST_MODE mode.

sl_si91x_calibration_read#

sl_status_t sl_si91x_calibration_read (sl_si91x_calibration_read_t target, sl_si91x_calibration_read_t * calibration_read)

Read the calibration data from the Flash/EFuse storage.

This function reads the calibration data from the specified storage (Flash or EFuse) and provides it in the calibration_read parameter.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

sl_si91x_evm_offset#

sl_status_t sl_si91x_evm_offset (const sl_si91x_evm_offset_t * evm_offset)

Provide feedback on the error caused by the EVM offset.

This function provides feedback on the error caused by the Error Vector Magnitude (EVM) offset. The EVM offset is specified using the sl_si91x_evm_offset_t structure.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

Note

• In FCC-certified modules, this API will trigger an error SL_STATUS_SI91X_FEATURE_NOT_AVAILABLE if used, except when in SL_SI91X_TRANSMIT_TEST_MODE mode.

sl_si91x_evm_write#

sl_status_t sl_si91x_evm_write (const sl_si91x_evm_write_t * evm_write)

Command the firmware to update the existing Flash/EFuse calibration data.

This function commands the firmware to update the existing Flash/EFuse calibration data using the provided EVM calibration configuration.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init, sl_si91x_evm_offset, and sl_si91x_transmit_test_start should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

Note

• In FCC-certified modules, this API will trigger an error SL_STATUS_SI91X_FEATURE_NOT_AVAILABLE if used, except when in SL_SI91X_TRANSMIT_TEST_MODE mode.

sl_si91x_efuse_read#

sl_status_t sl_si91x_efuse_read (const sl_si91x_efuse_read_t * efuse_read, uint8_t * efuse_read_buf)

Command the firmware to read data from the Efuse memory location.

This function commands the firmware to read data from the specified Efuse memory location. The data is read into the provided buffer.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

sl_si91x_dpd_calibration#

sl_status_t sl_si91x_dpd_calibration (const sl_si91x_get_dpd_calib_data_t * dpd_calib_data)

Update Flash/EFuse DPD data.

This function updates the Flash/EFuse DPD (Digital Pre-Distortion) data using the provided DPD calibration data.

This is a blocking API.

• Pre-conditions:

  • sl_wifi_init and sl_si91x_transmit_test_start should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

Note

• In FCC-certified modules, this API will trigger an errorSL_STATUS_SI91X_FEATURE_NOT_AVAILABLE if used, except when in SL_SI91X_TRANSMIT_TEST_MODE mode.

sl_si91x_enable_radio#

sl_status_t sl_si91x_enable_radio (void )

Enable wireless radio.

This function enables the wireless radio on the Si91x device.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

sl_si91x_disable_radio#

sl_status_t sl_si91x_disable_radio (void )

Disable wireless radio.

This function disables the wireless radio on the Si91x device.

• Pre-conditions:

  • sl_wifi_init should be called before this API.

Returns

• sl_status_t. See Status Codes and Additional Status Codes for details.

sl_si91x_set_listen_interval#

void sl_si91x_set_listen_interval (uint32_t listen_interval)

Set the Wi-Fi listen interval for the Si91x device.

This function sets the Wi-Fi listen interval for the Si91x device. The listen interval determines how often the device wakes up to listen for beacon frames from the access point.