WiSeConnect Status Codes#

OS operation failed.

Bootup options were not saved.

Bootup options checksum validation failed.

Bootloader version does not match expected version.

Waiting for the board to be ready.

No valid firmware present.

Provided option is invalid.

SPI is currently busy.

Timeout waiting for card to be ready.

Firmware load or upgrade operation timed out.

WiFi network does not exist.

WiFi network is not authenticated.

Device attempts to connect to a secured WiFi network without providing the correct security key or credentials.

Input/Output Control operation failed.

WiFi buffer temporarily unavailable.

WiFi buffer permanently unavailable.

WPS PBC overlap detected.

WiFi connection lost.

No space for additional event handlers.

Semaphore manipulation error.

Packet retrieval cancelled due to flow control.

Packet retrieval cancelled due to lack of bus credits.

Packet retrieval cancelled due to no pending packets.

WiFi core disabled due to no clock.

WiFi core disabled because it is in reset state.

Unsupported WiFi function.

Error occurred while writing to the WLAN register.

SDIO bus failed to initialize.

WiFi join operation is still in progress.

Specified WiFi network was not found.

Invalid status encountered during WiFi join.

Unknown WiFi interface specified.

Error occurred during SDIO receive operation.

Hardware tag header is corrupt.

Failed to allocate a buffer for WiFi receive operation.

Error occurred while reading a bus hardware register.

Failed to create a new WiFi thread.

Error occurred while manipulating a WiFi queue.

Error occurred while moving the current pointer of a buffer.

Error occurred while setting the size of the packet buffer.

Null stack pointer passed when a non-null pointer was required.

Error occurred while deleting a WiFi thread.

Failed to put a WiFi thread to sleep.

Failed to allocate a WiFi packet buffer.

The requested WiFi interface is not active.

The requested delay for WiFi operation is too long.

The specified WiFi duty cycle is outside the valid range.

The returned Pairwise Master Key (PMK) length is incorrect.

The security type of the WiFi Access Point is unknown.

WEP security is not allowed; use Open security instead.

WPA/WPA2 key length must be between 8 and 64 bytes.

The specified WiFi filter ID was not found.

Failed to read the SPI ID (0xfeedbead) from the chip.

Size mismatch between SPI and SDPCM header.

Attempted to register a multicast address that is already registered.

SDIO transfer failed after exceeding the maximum number of retries.

Null pointer argument passed to a function.

Error occurred while attempting to delete a thread.

Semaphore or mutex wait operation was aborted.

Unaligned message found in the queue.

Error occurred during a mutex operation.

Error occurred during decryption over a secure link.

Error occurred during key renegotiation over a secure link.

Invalid operation mode provided.

Invalid encryption method provided.

Error due to duplicate entropy elements in TRNG.

Provided MAC address is invalid.

Provided QoS priority is invalid.

Provided channel is invalid.

Provided data rate is invalid.

Provided transceiver configuration parameters are invalid.

Return when parameter passed to Crypto SAPI is invalid.

Return in AEAD (CCM, GCM, Chachapoly) decryption function, when MAC generated during decryption does not match the MAC passed.

Scan command issued while device is already associated with an access point.

No access point found.

Incorrect PSK provided while trying to join an access point with WEP security enabled.

Invalid band specified.

Device is not associated or is in an unassociated state.

De-authentication received from access point.

Failed to associate with the access point during "Join".

Invalid channel specified.

Authentication failure during "Join". Unable to find access point during join which was found during scan.

Missed beacon from access point during join.

Non-existent MAC address supplied in "Disassociate" command.

EAP configuration is not completed.

Memory allocation failed or store configuration checksum failed.

Insufficient or incorrect information provided in join command.

Not an access point interface.

Push button command issued before the expiry of the previous push button command.

Rejoin failure: Access point not found.

Operation failed: Frequency not supported.

Operation failed: Invalid operation mode.

EAP configuration failed.

P2P configuration failed.

Failed to start Group Owner negotiation.

Join operation timed out.

Command issued in an invalid state.

Invalid parameters for Query GO in the current operating mode.

Failed to form access point.

Invalid scan input parameters.

Command issued during re-join operation.

Incorrect parameters provided for the command.

Provision discovery failed in P2P mode.

PSK length less than 8 bytes or more than 63 bytes.

Failed to clear or to set the Enterprise Certificate (Set Certificate).

P2P Group Owner negotiation failed.

Association between nodes failed in P2P WPS mode due to timeout.

Command issued by the Host while the device is executing an internal operation (for example, auto-join or auto-create).

Invalid WEP key length.

ICMP request timed out.

ICMP data size exceeds the maximum limit.

Data packet size exceeded the limit, MQTT published the data and length mismatched, or MQTT send data packet exceeded the limit.

ARP cache entry not found.

UART command timed out.

Fixed data rate not supported by the connected AP.

Maximum length exceeded for username, password, client ID, or topic in MQTT.

Invalid WPS PIN.

Invalid WPS PIN length.

Invalid PMK length.

SSID not present for PMK generation.

SSID incorrect for PMK generation(more than 32 bytes).

Band not supported.

Invalid user store configuration length.

Invalid command length (exceeds the number of characters specified in the PRM).

Data packet dropped.

WEP key not provided.

Store config profile length error.

PSK or PMK not provided.

Invalid security mode in join command.

Maximum beacon miscount reached: De-authentication due to beacon miss.

De-authentication request received from supplicant.

De-authentication request received from AP after channel switching.

Synchronization missed.

Authentication timeout occurred.

Association timeout.

BG scan in given channels is not allowed.

Scanned SSID and SSID given in join are not matching.

The number of clients exceeds the maximum number of supported stations.

The specified HT capabilities are not supported.

UART flow control is not supported.

ZB/BT/BLE packet received, but the protocol is not enabled.

Management packet dropped.

The current RF mode is invalid.

Power save is not supported for the specified interface.

Concurrent AP is in a connected state.

Channel mismatch between connected AP and station.

IAP coprocessor error occurred.

WPS is not supported in the current operating mode.

Concurrent AP channel does not match the connected station channel.

PBC session overlap error.

The Bluetooth feature bitmap is invalid.

The 4/4 confirmation of the four-way handshake failed.

MAC address is not present in the MAC-based join.

Concurrent mode requires both AP and client to be up for configuration.

Certificate load operation is not allowed in flash memory.

Certificate load operation is not allowed in RAM.

Certificate load failed due to an incorrect index.

Access Point HT capabilities are not enabled.

The specified address family is not supported by the protocol.

The provided beacon interval or DTIM period is invalid.

The provided configuration range is invalid.

The provided configuration type (for example, RTS threshold) is invalid.

An error occurred with the MQTT command.

The listen interval in power save mode is greater than that specified in the join command.

The WLAN radio has been deregistered.

SAE authentication failed due to multiple confirm frames received from the Access Point.

The Access Point does not support the EC-group set by the station.

802.11ax (Wi-Fi 6) is not supported in Access Point mode.

Non-preferred channel configuration failed.

Error occurs when HE_PARAMS_SUPPORT and SLI_SI91X_ENABLE_TWT_FEATURE macros are not enabled.

Error occurs when a TWT config command is issued while there is already an active TWT session.

Error occurs when a TWT teardown command is issued with a flow ID that does not match the existing session flow ID.

Error occurs when a teardown command is issued while there is no active TWT session.

Indicates that a TWT session is not feasible. This error is thrown only when the TWT Auto Selection API is used.

Error occurs when the AP does not support TWT information frame reception.

Error occurs when there is no active TWT agreement corresponding to the given flow ID.

Indicates that a suspend or resume TWT action is currently in progress.

Error occurs when TWT information frame packet creation fails in firmware.

Error occurs when the station TSF is invalid, typically when the station is not connected or has not received at least one beacon.

Error occurs when the server does not support the level of the MQTT protocol requested by the client.

Error occurs when the client identifier is correct UTF-8 but is not allowed by the server.

Error occurs when the network connection has been made but the MQTT service is unavailable.

The data in the username or password is malformed.

The client is not authorized to connect.

Disconnection due to SA Query Timeout.

Feature to add peers in MAC layer is disabled.

Peer already exists in MAC layer.

Max peer limit reached in MAC layer.

Peer not found in MAC layer.

Duplicate entry exists in DNS server table.

Memory error: No memory available.

Invalid characters in JSON object.

Update commands: No such key found.

No such file found: Re-check file name.

No corresponding web page exists with the same filename.

Space unavailable for new file.

Invalid input data, re-check filename, lengths, etc.

Space unavailable for new file.

Existing file overwrite: Exceeds size of previous file. Use erase and try again.

No such file found. Re-check filename.

Memory Error: No memory available.

Received more web page data than the total length initially specified.

Error in set region command.

Web page current chunk length is incorrect.

Error in AP set region command.

Error in AP set region command parameters.

Region code not supported.

Error in extracting country region from beacon.

Device does not have selected region support.

SSL/TLS context create failed.

SSL/TLS handshake failed. Socket will be closed.

SSL/TLS max sockets reached.

FTP client is not connected.

Cipher set failure.

HTTP credentials maximum length exceeded.

Feature not supported.

Unable to write to flash OR flash data verification failed.

Calibration data verification failed.

SNMP internal error.

SNMP invalid IP protocol error.

Unsupported power index for 915.

Efuse data is invalid.

No data received or receive timeout.

Insufficient data for converting NTP time to mm-dd-yy time format.

Invalid SNTP server address.

SNTP client not started.

SNTP server not available. Client will not get any time update service from current server.

SNTP server authentication failed.

Internal error.

Entry not found for multicast IP address.

No more entries found for multicast.

IP address error.

Socket already bound.

Port not available.

Socket is not created.

ICMP request failed.

Maximum listen sockets reached.

DHCP duplicate listen.

Port not in closed state.

Socket is closed or in process of closing.

Process in progress.

Trying to connect to a non-existing TCP server socket.

Error in the length of the command (exceeds the number of characters mentioned in the PRM).

Wrong packet information.

Socket is still bound.

No free port available.

Invalid port specified.

Corrupted RPS header encountered or Received empty RPS file(no data) during firmware update.

Feature not supported.

Socket is not in a connected state. Disconnected from the server. In the case of FTP, the user needs to issue a destroy command after receiving this error.

POP3 session creation failed or POP3 session got terminated.

DHCPv6 handshake failure.

DHCP invalid IP response.

SMTP authentication error.

No DNS server was specified, SMTP over size mail data.

SMTP invalid server reply.

DNS query failed, SMTP internal error.

Bad DNS address, SMTP server error code received.

SMTP invalid parameters.

SMTP packet allocation failed.

SMTP Greet reply failed.

Parameter error, SMTP hello reply error.

SMTP mail reply error.

SMTP RCPT reply error.

SMTP message reply error.

SMTP data reply error.

SMTP authentication reply error.

SMTP server error reply.

DNS duplicate entry.

SMTP oversize server reply.

SMTP client not initialized.

DNS IPv6 not supported.

Invalid mail index specified for the POP3 mail retrieve command.

SSL/TLS handshake process failed.

FTP client is either not connected or has been disconnected from the FTP server.

FTP client is still connected and has not been disconnected.

FTP file could not be opened.

SSL/TLS handshake timed out or the FTP file was not closed properly.

Expected 1XX response from the FTP server was not received.

Expected 2XX response from the FTP server was not received.

Expected 22X response from the FTP server was not received.

Expected 23X response from the FTP server was not received.

Expected 3XX response from the FTP server was not received.

Expected 33X response from the FTP server was not received.

HTTP request timed out.

HTTP request failed.

HTTP PUT client request timed out.

Authentication process failed.

Invalid packet length. Content length and received data length mismatch.

Server responds before HTTP client request is complete.

HTTP/HTTPS password is too long.

MQTT ping timeout error.

MQTT command sent in incorrect state.

MQTT ACK timeout error.

POP3 error for invalid mail index.

Firmware update successful.

Firmware update failed.

Memory allocation failed in NWP during firmware upgradation.

Insufficient space in NWP flash memory during firmware upgradation.

Wrong packet info.

All payload chunks length together can't be greater than total image size in header, during firmware upgradation.

Listening TCP socket in device is not connected to the remote peer, or the LTCP socket is not yet opened in the device.

Socket limit exceeded. More than 10 sockets opened.

HTTP OTAF invalid packet.

TCP/IP initialization failed.

Cannot create IP in same interface in concurrent mode.

HTTP OTAF incomplete packet.

Invalid or mismatched store configuration profile type.

MQTT remote terminate error.

MQTT remote terminate error due to keep-alive response timeout.

Byte stuffing error in AT mode.

Invalid command (e.g. parameters insufficient or invalid in the command). Invalid operation (for example, power save command with the same mode given twice, accessing wrong socket, creating more than allowed sockets ).

HTTP OTAF no packet received.

TCP socket is not connected.

Station count exceeded the maximum supported stations.

Unable to send TCP data.

Socket buffer too small.

Invalid content in the DNS response to the DNS resolution query.

DNS class error in response to the DNS resolution query.

DNS count error in response to the DNS resolution query.

DNS return code error in the response to the DNS resolution query.

DNS Opcode error in the response to the DNS resolution query.

DNS id mismatch between the DNS resolution request and response.

Invalid input provided in the DNS resolution query.

DNS response was timed out.

ARP request failure.

Failed to update TCP window.

DHCP lease time expired.

DHCP handshake failure.

WebSocket creation failed.

Attempted to connect to a non-existent TCP server socket on the remote side.

Attempted to close a non-existent or invalid socket descriptor.

The provided socket parameters are invalid.

The requested feature is not supported.

The socket is already open.

Attempted to open more than the maximum allowed number of sockets.

Data length exceeds the Maximum Segment Size (MSS).

Device unable to configure IP address due to an IP conflict.

The requested feature is not enabled.

DHCP server is not configured in AP mode.

Invalid parameters provided for the AP set region command.

SSL/TLS is not supported.

JSON format is not supported.

The specified operating mode is invalid.

Invalid socket configuration parameters.

Web socket creation timeout.

Parameter exceeds the maximum allowed value.

The socket read operation timed out.

The command sequence is invalid.

The DNS response timed out.

Failed to create an HTTP socket.

An HTTP GET command is currently in progress.

TCP socket close command issued before receiving the response of the previous close command.

'Wait On Host' feature is not enabled.

Store configuration checksum validation failed.

TCP keep-alive timed out.

TCP ACK failed for TCP SYN-ACK.

Memory limit exceeded in the given operating mode.

Memory limit exceeded in the operating mode during auto join/create.

The MDNS command type is invalid.

The PUF operation is blocked.

The PUF activation code is invalid.

The PUF input parameters are invalid.

The PUF is in an error state.

The PUF operation is not allowed.

The PUF operation failed.

Input message length exceed the expected length.

Auto join or user store configuration is in progress.

Received an invalid RSNIE from the AP to the station.

Maximum number of invalid SNTP attempts reached.

The frequency offset sent is zero.

Frequency offset specified goes beyond upper or lower limits and indicates that frequency offset cannot be changed further.

Unknown HCI command.

Unknown Connection Identifier.

Hardware failure.

Page timeout.

Authentication failure.

Pin missing.

Memory capacity exceeded.

Connection timeout.

Connection limit exceeded.

SCO limit exceeded.

ACL Connection already exists.

Command disallowed.

Connection rejected due to limited resources .

Connection rejected due to security reasons.

Connection rejected for BD address.

Connection accept timeout.

Unsupported feature or parameter.

Invalid HCI command parameter.

Remote user terminated connection.

Remote device terminated connection due to low resources .

Remote device terminated connection due to power off .

Local device terminated connection.

Repeated attempts.

Pairing not allowed.

Unknown LMP PDU.

Unsupported remote feature.

SCO offset rejected.

SCO interval rejected.

SCO Air mode rejected.

Invalid LMP parameters.

Unspecified.

Unsupported LMP Parameter.

Role change not allowed.

LMP response timeout.

LMP transaction collision.

LMP PDU not allowed.

Encryption mode not acceptable.

Link key cannot change.

Requested QOS not supported.

Instant passed.

Pairing with unit key not supported.

Different transaction collision.

Reserved 1.

QOS parameter not acceptable.

QOS rejected.

Channel classification not supported.

Insufficient security.

Parameter out of mandatory range.

Reserved 2.

Role switch pending.

Reserved 3.

Reserved slot violation.

Role switch failed.

Extended Inquiry Response too large.

Extended SSP not supported.

Host busy pairing.

Wrong BD Address.

Connection Failed to be Establish.

Invalid Gain table payload length.

Invalid Region.

Invalid Gain Table offset request type.

Invalid Node ID.

BT Invalid Command.

Invalid Args.

Unknown.

Firmware Timeout.

Memory alloc fail.

I/O fail.

Unsupported.

Short buffer.

Buf overflow .

Too large buffer.

I/O abort.

File open fail.

OS task invalid priority.

OS task prio exists.

OS task not stopped.

OS sem max value.

OS sem not available.

OS sem reset.

OS mutex not owner.

OS mutex not locked.

OS mutex lock failed.

OS mutex try lock failed.

OS msg queue full.

OS message queue empty.

Pipe empty.

Pipe full.

Invalid len.

Pipe read in use.

Pipe write in use.

OS timer expired.

OS timer state running.

OS cannot wait.

OS mem pool empty.

OS mem pool size short.

Directed Advertising Timeout.

Connection terminated due to MIC failure.

Invalid Handle Range.

Memory is not sufficient.

Invalid Parameters.

BLE Buffer Count Exceeded.

BLE Buffer already in use.

Invalid Attribute Length When Small Buffer Mode is Configured.

Invalid Name length when set to more than 16 bytes.

Invalid Handle.

Read not permitted.

Write not permitted.

Invalid PDU.

Insufficient authentication.

Request not supported .

Invalid offset.

Insufficient authorization.

Prepare queue full.

Attribute not found.

Attribute not Long.

Insufficient encryption key size.

Invalid attribute value length.

Unlikely error.

Insufficient encryption.

Unsupported group type.

Insufficient resources.

GATT Timeout.

Data Maintained in Host.

SMP Passkey entry failed.

SMP OOB not available.

SMP Authentication Requirements.

SMP confirm value failed.

SMP Pairing not supported.

SMP Encryption key size insufficient.

SMP command not supported.

SMP pairing failed.

SMP repeated attempts.

SMP Invalid parameters.

SMP DH Key check failed.

SMP Numeric Comparison Failed.

SMP Invalid Keys Generated.

SMP Identical Public Key.

PSM Conn Failed.

BLE Remote device found.

BLE Remote device not found.

BLE Remote device structure full.

Unable to change state.

BLE not Connected.

BLE socket not available.

Attribute record not found.

Attribute entry not found.

Profile record full.

Attribute record full.

BLE profile not found(profile handler invalid).

BLE Attribute Buffer Full .

BLE Connection Sock not Available.

BLE Remote Credits not Available.

Parameter is outoff the manadatory range.