SPI#

Functions#

int16_t

rsi_frame_read(uint8_t *pkt_buffer)

Reads response for every command and data from the module.

int16_t

rsi_frame_write(rsi_frame_desc_t *uFrameDscFrame, uint8_t *payloadparam, uint16_t size_param)

Process a command to the wlan module.

int16_t

rsi_pre_dsc_rd(uint8_t *dbuf)

Perform a pre-frame decriptor read.

int16_t

rsi_pkt_rd(uint8_t *buf, uint16_t dummy_len, uint16_t total_len)

Perform frame decriptor and payload read.

int16_t

rsi_spi_frame_dsc_wr(rsi_frame_desc_t *uFrameDscFrame)

Write a Frame descriptor.

int16_t

rsi_spi_frame_data_wr(uint16_t bufLen, uint8_t *dBuf, uint16_t tbufLen, uint8_t *tBuf)

Perform Frame Data Write.

int16_t

rsi_send_c1c2(uint8_t c1, uint8_t c2)

Send the C1 & C2 commands bytes, should check response for C1 command, if busy, should retry.

int16_t

rsi_send_c3c4(uint8_t c3, uint8_t c4)

The C3 & C4 command bytes to send.

int16_t

rsi_spi_wait_start_token(uint32_t timeout, uint8_t mode)

Loop reading the SPI until a start token, 0x55, is received.

int16_t

rsi_set_intr_mask(uint8_t interruptMask)

Set the INTERRUPT MASK REGISTER of the module.

int16_t

rsi_set_intr_type(uint32_t interruptMaskVal)

Set the INTERRUPT TYPE of the module based on selected LOAD_IMAGE.

int16_t

rsi_clear_interrupt(uint8_t interruptClear)

Clear the interrupt register.

int16_t

rsi_device_interrupt_status(uint8_t *int_status)

Return the module SPI interrupt register status.

int16_t

rsi_spi_pkt_len(uint16_t *length)

Return the length of the incoming packet.

int16_t

rsi_spi_high_speed_enable(void)

Configure the module SPI interface to high speed mode.

int16_t

rsi_spi_iface_init(void)

Initialize the wlan module�s Slave SPI interface.

void

rsi_ulp_wakeup_init(void)

Initialize the with modules Slave SPI interface on ulp wakeup.

int16_t

rsi_mem_wr(uint32_t addr, uint16_t len, uint8_t *dBuf)

Perform a memory write to the module.

int16_t

rsi_mem_rd(uint32_t addr, uint16_t len, uint8_t *dBuf)

Perform a memory read from the module.

int16_t

rsi_reg_rd(uint8_t regAddr, uint8_t *dBuf)

Read from a register in the module from the address specified.

int16_t

rsi_reg_rd2(uint8_t regAddr, uint16_t *dBuf)

Read from a register in the wlan module from the address specified.

int16_t

rsi_reg_wr(uint8_t regAddr, uint8_t *dBuf)

Write to a register in the module with an address specified.

Function Documentation#

rsi_frame_read#

int16_t rsi_frame_read (uint8_t * pkt_buffer)

Reads response for every command and data from the module.

Parameters

[in]

pkt_buffer

- pointer to buffer to which packet has to read

Returns

0 - SUCCESS < 0 - FAILURE -1 - SPI busy / Timeout in case of SPI -2 - SPI Failure in case of SPI

Note

Enable DEBUG_PACKET_EXCHANGE macro for spi level packet exchange debug prints and MAX_PRINT_PAYLOAD_LEN for configuring no.bytes of payload to print, by default it will print 8 bytes of payload.

Definition at line 67 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_pre_dsc_rd , RSI_SUCCESS , rsi_pkt_rd , and rsi_bytes2R_to_uint16

rsi_frame_write#

int16_t rsi_frame_write (rsi_frame_desc_t * uFrameDscFrame, uint8_t * payloadparam, uint16_t size_param)

Process a command to the wlan module.

Parameters

[in]	uFrameDscFrame	- Frame descriptor
[in]	payloadparam	- Pointer to the command payload parameter structure
[in]	size_param	- Size of the payload for the command

Returns

0 - SUCCESS < 0 - FAILURE -1 - SPI busy / Timeout in case of SPI -2 - SPI Failure in case of SPI

Note

Enable DEBUG_PACKET_EXCHANGE macro for spi level packet exchange debug prints and MAX_PRINT_PAYLOAD_LEN for configuring no.bytes of payload to print, by default it will print 8 bytes of payload..

Definition at line 118 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_spi_frame_dsc_wr , RSI_SUCCESS , and rsi_spi_frame_data_wr

rsi_pre_dsc_rd#

int16_t rsi_pre_dsc_rd (uint8_t * dbuf)

Perform a pre-frame decriptor read.

Parameters

[in]

dbuf

- Pointer to the buffer into which pre-decriptor has to be read

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 164 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_send_c1c2 , RSI_SUCCESS , rsi_send_c3c4 , and rsi_spi_wait_start_token

rsi_pkt_rd#

int16_t rsi_pkt_rd (uint8_t * buf, uint16_t dummy_len, uint16_t total_len)

Perform frame decriptor and payload read.

Parameters

[in]	buf	- Pointer to the buffer into which decriptor and payload has to be read
[in]	dummy_len	- Number of dummy bytes which can be discarded
[in]	total_len	- Number of bytes to be read

Returns

0 - SUCCESS -1 - SPI busy / Timeout \nrsi_spi_frame_data_wr -2 - SPI Failure

Definition at line 225 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_send_c1c2 , RSI_SUCCESS , rsi_send_c3c4 , and rsi_spi_wait_start_token

rsi_spi_frame_dsc_wr#

int16_t rsi_spi_frame_dsc_wr (rsi_frame_desc_t * uFrameDscFrame)

Write a Frame descriptor.

Parameters

[in]

uFrameDscFrame

- Frame descriptor

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 300 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_send_c1c2 , RSI_SUCCESS , rsi_send_c3c4 , and rsi_frame_desc_s::frame_len_queue_no

rsi_spi_frame_data_wr#

int16_t rsi_spi_frame_data_wr (uint16_t bufLen, uint8_t * dBuf, uint16_t tbufLen, uint8_t * tBuf)

Perform Frame Data Write.

Parameters

[in]	bufLen	- Length of the data buffer to write
[in]	dBuf	- Pointer to the buffer of data to write
[in]	tbufLen	- Length of the data fragment to write
[in]	tBuf	- Pointer to the buffer of data fragment to write

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 356 of file driver/device_interface/spi/rsi_spi_frame_rd_wr.c

References rsi_send_c1c2 , RSI_SUCCESS , and rsi_send_c3c4

rsi_send_c1c2#

int16_t rsi_send_c1c2 (uint8_t c1, uint8_t c2)

Send the C1 & C2 commands bytes, should check response for C1 command, if busy, should retry.

Parameters

[in]	c1	- SPI c1 command
[in]	c2	- SPI c2 command

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 54 of file driver/device_interface/spi/rsi_spi_functs.c

Referenced by rsi_pre_dsc_rd , rsi_pkt_rd , rsi_spi_frame_dsc_wr , rsi_spi_frame_data_wr , rsi_mem_wr , rsi_mem_rd , rsi_reg_rd , rsi_reg_rd2 , and rsi_reg_wr

rsi_send_c3c4#

int16_t rsi_send_c3c4 (uint8_t c3, uint8_t c4)

The C3 & C4 command bytes to send.

Parameters

[in]	c3	- SPI c3 command bytes to be sent
[in]	c4	- SPI c4 command bytes to be sent

A succesful rsi_send_c1c2 is required before this function.

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 102 of file driver/device_interface/spi/rsi_spi_functs.c

Referenced by rsi_pre_dsc_rd , rsi_pkt_rd , rsi_spi_frame_dsc_wr , rsi_spi_frame_data_wr , rsi_mem_wr , and rsi_mem_rd

rsi_spi_wait_start_token#

int16_t rsi_spi_wait_start_token (uint32_t timeout, uint8_t mode)

Loop reading the SPI until a start token, 0x55, is received.

Parameters

[in]	timeout	- Timeout for start token.
[in]	mode	- To indicate 8-bit/32-bit mode.

Should issue read commands before using this function

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 130 of file driver/device_interface/spi/rsi_spi_functs.c

Referenced by rsi_pre_dsc_rd , rsi_pkt_rd , rsi_mem_rd , rsi_reg_rd , and rsi_reg_rd2

rsi_set_intr_mask#

int16_t rsi_set_intr_mask (uint8_t interruptMask)

Set the INTERRUPT MASK REGISTER of the module.

Parameters

[in]

interruptMask

- The value to set the mask register to

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 179 of file driver/device_interface/spi/rsi_spi_functs.c

References rsi_mem_wr , and RSI_SUCCESS

rsi_set_intr_type#

int16_t rsi_set_intr_type (uint32_t interruptMaskVal)

Set the INTERRUPT TYPE of the module based on selected LOAD_IMAGE.

Parameters

[in]

interruptMaskVal

- The value to set the mask register

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 215 of file driver/device_interface/spi/rsi_spi_functs.c

References rsi_mem_rd , rsi_mem_wr , and RSI_SUCCESS

rsi_clear_interrupt#

int16_t rsi_clear_interrupt (uint8_t interruptClear)

Clear the interrupt register.

Parameters

[in]

interruptClear

- The value to set the interrupt clear register to

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 248 of file driver/device_interface/spi/rsi_spi_functs.c

References rsi_mem_wr , and RSI_SUCCESS

rsi_device_interrupt_status#

int16_t rsi_device_interrupt_status (uint8_t * int_status)

Return the module SPI interrupt register status.

Parameters

[in]

int_status

- Pointer to the buffer of data to be read, assumed to be at least a byte

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 280 of file driver/device_interface/spi/rsi_spi_functs.c

rsi_spi_pkt_len#

int16_t rsi_spi_pkt_len (uint16_t * length)

Return the length of the incoming packet.

Parameters

[in]

length

- Pointer to the buffer of data to write, assumed to be at least 2 bytes long

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 314 of file driver/device_interface/spi/rsi_spi_functs.c

rsi_spi_high_speed_enable#

int16_t rsi_spi_high_speed_enable (void )

Configure the module SPI interface to high speed mode.

Parameters

[in]

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 349 of file driver/device_interface/spi/rsi_spi_functs.c

rsi_spi_iface_init#

int16_t rsi_spi_iface_init (void )

Initialize the wlan module�s Slave SPI interface.

Parameters

[in]

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 54 of file driver/device_interface/spi/rsi_spi_iface_init.c

References SL_PRINTF , and RSI_SUCCESS

rsi_ulp_wakeup_init#

void rsi_ulp_wakeup_init (void )

Initialize the with modules Slave SPI interface on ulp wakeup.

Parameters

[in]

Returns

void

Definition at line 98 of file driver/device_interface/spi/rsi_spi_iface_init.c

Referenced by rsi_req_wakeup , rsi_tx_event_handler , and rsi_rx_event_handler

rsi_mem_wr#

int16_t rsi_mem_wr (uint32_t addr, uint16_t len, uint8_t * dBuf)

Perform a memory write to the module.

Parameters

[in]	addr	- Address to write to
[in]	len	- Number of bytes to write
[in]	dBuf	- Pointer to the buffer of data to write

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 56 of file driver/device_interface/spi/rsi_spi_mem_rd_wr.c

References RSI_SUCCESS , rsi_reg_wr , rsi_uint32_to_4bytes , rsi_send_c1c2 , and rsi_send_c3c4

rsi_mem_rd#

int16_t rsi_mem_rd (uint32_t addr, uint16_t len, uint8_t * dBuf)

Perform a memory read from the module.

Parameters

[in]	addr	- Address to read from
[in]	len	- Number of bytes to read
[in]	dBuf	- Pointer to the buffer to receive the data into

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 126 of file driver/device_interface/spi/rsi_spi_mem_rd_wr.c

References RSI_SUCCESS , rsi_reg_wr , rsi_send_c1c2 , rsi_send_c3c4 , and rsi_spi_wait_start_token

rsi_reg_rd#

int16_t rsi_reg_rd (uint8_t regAddr, uint8_t * dBuf)

Read from a register in the module from the address specified.

Parameters

[in]	regAddr	- Address of spi register to read, addr is 6-bits, upper 2 bits must be cleared
[in]	dBuf	- Pointer to the buffer of data to write, assumed to be at least 2 bytes long

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 53 of file driver/device_interface/spi/rsi_spi_reg_rd_wr.c

References rsi_send_c1c2 , RSI_SUCCESS , and rsi_spi_wait_start_token

rsi_reg_rd2#

int16_t rsi_reg_rd2 (uint8_t regAddr, uint16_t * dBuf)

Read from a register in the wlan module from the address specified.

Parameters

[in]	regAddr	- Address of spi register to read, addr is 6-bits, upper 2 bits must be cleared
[in]	dBuf	- Pointer to the buffer of data to write, assumed to be at least 2 bytes long

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 96 of file driver/device_interface/spi/rsi_spi_reg_rd_wr.c

References rsi_send_c1c2 , and rsi_spi_wait_start_token

rsi_reg_wr#

int16_t rsi_reg_wr (uint8_t regAddr, uint8_t * dBuf)

Write to a register in the module with an address specified.

Parameters

[in]	regAddr	- Address of spi register to be written
[in]	dBuf	- Pointer to the buffer of data to write, assumed to be at least 2 bytes long

Returns

0 - SUCCESS -1 - SPI busy / Timeout -2 - SPI Failure

Definition at line 142 of file driver/device_interface/spi/rsi_spi_reg_rd_wr.c

References rsi_send_c1c2 , and RSI_SUCCESS