Register definitions
Description
Register definitions.
ICM20648 register banks | |
#define | ICM20648_BANK_0 (0 << 7) |
Register bank 0. | |
#define | ICM20648_BANK_1 (1 << 7) |
Register bank 1. | |
#define | ICM20648_BANK_2 (2 << 7) |
Register bank 2. | |
#define | ICM20648_BANK_3 (3 << 7) |
Register bank 3. | |
Register and associated bit definitions | |
#define | ICM20648_REG_WHO_AM_I (ICM20648_BANK_0 | 0x00) |
Device ID register | |
#define | ICM20648_REG_USER_CTRL (ICM20648_BANK_0 | 0x03) |
User control register | |
#define | ICM20648_BIT_DMP_EN 0x80 |
DMP enable bit | |
#define | ICM20648_BIT_FIFO_EN 0x40 |
FIFO enable bit | |
#define | ICM20648_BIT_I2C_MST_EN 0x20 |
I2C master I/F enable bit | |
#define | ICM20648_BIT_I2C_IF_DIS 0x10 |
Disable I2C, enable SPI bit | |
#define | ICM20648_BIT_DMP_RST 0x08 |
DMP module reset bit | |
#define | ICM20648_BIT_DIAMOND_DMP_RST 0x04 |
SRAM module reset bit | |
#define | ICM20648_REG_LP_CONFIG (ICM20648_BANK_0 | 0x05) |
Low Power mode config register | |
#define | ICM20648_BIT_I2C_MST_CYCLE 0x40 |
I2C master cycle mode enable | |
#define | ICM20648_BIT_ACCEL_CYCLE 0x20 |
Accelerometer cycle mode enable | |
#define | ICM20648_BIT_GYRO_CYCLE 0x10 |
Gyroscope cycle mode enable | |
#define | ICM20648_REG_PWR_MGMT_1 (ICM20648_BANK_0 | 0x06) |
Power Management 1 register | |
#define | ICM20648_BIT_H_RESET 0x80 |
Device reset bit | |
#define | ICM20648_BIT_SLEEP 0x40 |
Sleep mode enable bit | |
#define | ICM20648_BIT_LP_EN 0x20 |
Low Power feature enable bit | |
#define | ICM20648_BIT_TEMP_DIS 0x08 |
Temperature sensor disable bit | |
#define | ICM20648_BIT_CLK_PLL 0x01 |
Auto clock source selection setting | |
#define | ICM20648_REG_PWR_MGMT_2 (ICM20648_BANK_0 | 0x07) |
Power Management 2 register | |
#define | ICM20648_BIT_PWR_ACCEL_STBY 0x38 |
Disable accelerometer | |
#define | ICM20648_BIT_PWR_GYRO_STBY 0x07 |
Disable gyroscope | |
#define | ICM20648_BIT_PWR_ALL_OFF 0x7F |
Disable both accel and gyro | |
#define | ICM20648_REG_INT_PIN_CFG (ICM20648_BANK_0 | 0x0F) |
Interrupt Pin Configuration register | |
#define | ICM20648_BIT_INT_ACTL 0x80 |
Active low setting bit | |
#define | ICM20648_BIT_INT_OPEN 0x40 |
Open collector configuration bit | |
#define | ICM20648_BIT_INT_LATCH_EN 0x20 |
Latch enable bit | |
#define | ICM20648_REG_INT_ENABLE (ICM20648_BANK_0 | 0x10) |
Interrupt Enable register | |
#define | ICM20648_BIT_WOM_INT_EN 0x08 |
Wake-up On Motion enable bit | |
#define | ICM20648_REG_INT_ENABLE_1 (ICM20648_BANK_0 | 0x11) |
Interrupt Enable 1 register | |
#define | ICM20648_BIT_RAW_DATA_0_RDY_EN 0x01 |
Raw data ready interrupt enable bit | |
#define | ICM20648_REG_INT_ENABLE_2 (ICM20648_BANK_0 | 0x12) |
Interrupt Enable 2 register | |
#define | ICM20648_BIT_FIFO_OVERFLOW_EN_0 0x01 |
FIFO overflow interrupt enable bit | |
#define | ICM20648_REG_INT_ENABLE_3 (ICM20648_BANK_0 | 0x13) |
Interrupt Enable 2 register | |
#define | ICM20648_REG_INT_STATUS (ICM20648_BANK_0 | 0x19) |
Interrupt Status register | |
#define | ICM20648_BIT_WOM_INT 0x08 |
Wake-up on motion interrupt occurred bit | |
#define | ICM20648_BIT_PLL_RDY 0x04 |
PLL ready interrupt occurred bit | |
#define | ICM20648_REG_INT_STATUS_1 (ICM20648_BANK_0 | 0x1A) |
Interrupt Status 1 register | |
#define | ICM20648_BIT_RAW_DATA_0_RDY_INT 0x01 |
Raw data ready interrupt occurred bit | |
#define | ICM20648_REG_INT_STATUS_2 (ICM20648_BANK_0 | 0x1B) |
Interrupt Status 2 register | |
#define | ICM20648_REG_ACCEL_XOUT_H_SH (ICM20648_BANK_0 | 0x2D) |
Accelerometer X-axis data high byte | |
#define | ICM20648_REG_ACCEL_XOUT_L_SH (ICM20648_BANK_0 | 0x2E) |
Accelerometer X-axis data low byte | |
#define | ICM20648_REG_ACCEL_YOUT_H_SH (ICM20648_BANK_0 | 0x2F) |
Accelerometer Y-axis data high byte | |
#define | ICM20648_REG_ACCEL_YOUT_L_SH (ICM20648_BANK_0 | 0x30) |
Accelerometer Y-axis data low byte | |
#define | ICM20648_REG_ACCEL_ZOUT_H_SH (ICM20648_BANK_0 | 0x31) |
Accelerometer Z-axis data high byte | |
#define | ICM20648_REG_ACCEL_ZOUT_L_SH (ICM20648_BANK_0 | 0x32) |
Accelerometer Z-axis data low byte | |
#define | ICM20648_REG_GYRO_XOUT_H_SH (ICM20648_BANK_0 | 0x33) |
Gyroscope X-axis data high byte | |
#define | ICM20648_REG_GYRO_XOUT_L_SH (ICM20648_BANK_0 | 0x34) |
Gyroscope X-axis data low byte | |
#define | ICM20648_REG_GYRO_YOUT_H_SH (ICM20648_BANK_0 | 0x35) |
Gyroscope Y-axis data high byte | |
#define | ICM20648_REG_GYRO_YOUT_L_SH (ICM20648_BANK_0 | 0x36) |
Gyroscope Y-axis data low byte | |
#define | ICM20648_REG_GYRO_ZOUT_H_SH (ICM20648_BANK_0 | 0x37) |
Gyroscope Z-axis data high byte | |
#define | ICM20648_REG_GYRO_ZOUT_L_SH (ICM20648_BANK_0 | 0x38) |
Gyroscope Z-axis data low byte | |
#define | ICM20648_REG_TEMPERATURE_H (ICM20648_BANK_0 | 0x39) |
Temperature data high byte | |
#define | ICM20648_REG_TEMPERATURE_L (ICM20648_BANK_0 | 0x3A) |
Temperature data low byte | |
#define | ICM20648_REG_TEMP_CONFIG (ICM20648_BANK_0 | 0x53) |
Temperature Configuration register | |
#define | ICM20648_REG_FIFO_EN_1 (ICM20648_BANK_0 | 0x66) |
FIFO Enable 1 register | |
#define | ICM20648_REG_FIFO_EN_2 (ICM20648_BANK_0 | 0x67) |
FIFO Enable 2 register | |
#define | ICM20648_BIT_ACCEL_FIFO_EN 0x10 |
Enable writing acceleration data to FIFO bit | |
#define | ICM20648_BITS_GYRO_FIFO_EN 0x0E |
Enable writing gyroscope data to FIFO bit | |
#define | ICM20648_REG_FIFO_RST (ICM20648_BANK_0 | 0x68) |
FIFO Reset register | |
#define | ICM20648_REG_FIFO_MODE (ICM20648_BANK_0 | 0x69) |
FIFO Mode register | |
#define | ICM20648_REG_FIFO_COUNT_H (ICM20648_BANK_0 | 0x70) |
FIFO data count high byte | |
#define | ICM20648_REG_FIFO_COUNT_L (ICM20648_BANK_0 | 0x71) |
FIFO data count low byte | |
#define | ICM20648_REG_FIFO_R_W (ICM20648_BANK_0 | 0x72) |
FIFO Read/Write register | |
#define | ICM20648_REG_DATA_RDY_STATUS (ICM20648_BANK_0 | 0x74) |
Data Ready Status register | |
#define | ICM20648_BIT_RAW_DATA_0_RDY 0x01 |
Raw Data Ready bit | |
#define | ICM20648_REG_FIFO_CFG (ICM20648_BANK_0 | 0x76) |
FIFO Configuration register | |
#define | ICM20648_BIT_MULTI_FIFO_CFG 0x01 |
Interrupt status for each sensor is required | |
#define | ICM20648_BIT_SINGLE_FIFO_CFG 0x00 |
Interrupt status for only a single sensor is required | |
#define | ICM20648_REG_XA_OFFSET_H (ICM20648_BANK_1 | 0x14) |
Acceleration sensor X-axis offset cancellation high byte | |
#define | ICM20648_REG_XA_OFFSET_L (ICM20648_BANK_1 | 0x15) |
Acceleration sensor X-axis offset cancellation low byte | |
#define | ICM20648_REG_YA_OFFSET_H (ICM20648_BANK_1 | 0x17) |
Acceleration sensor Y-axis offset cancellation high byte | |
#define | ICM20648_REG_YA_OFFSET_L (ICM20648_BANK_1 | 0x18) |
Acceleration sensor Y-axis offset cancellation low byte | |
#define | ICM20648_REG_ZA_OFFSET_H (ICM20648_BANK_1 | 0x1A) |
Acceleration sensor Z-axis offset cancellation high byte | |
#define | ICM20648_REG_ZA_OFFSET_L (ICM20648_BANK_1 | 0x1B) |
Acceleration sensor Z-axis offset cancellation low byte | |
#define | ICM20648_REG_TIMEBASE_CORR_PLL (ICM20648_BANK_1 | 0x28) |
PLL Timebase Correction register | |
#define | ICM20648_REG_GYRO_SMPLRT_DIV (ICM20648_BANK_2 | 0x00) |
Gyroscope Sample Rate Divider register | |
#define | ICM20648_REG_GYRO_CONFIG_1 (ICM20648_BANK_2 | 0x01) |
Gyroscope Configuration 1 register | |
#define | ICM20648_BIT_GYRO_FCHOICE 0x01 |
Gyro Digital Low-Pass Filter enable bit | |
#define | ICM20648_SHIFT_GYRO_FS_SEL 1 |
Gyro Full Scale Select bit shift | |
#define | ICM20648_SHIFT_GYRO_DLPCFG 3 |
Gyro DLPF Config bit shift | |
#define | ICM20648_MASK_GYRO_FULLSCALE 0x06 |
Gyro Full Scale Select bitmask | |
#define | ICM20648_MASK_GYRO_BW 0x39 |
Gyro Bandwidth Select bitmask | |
#define | ICM20648_GYRO_FULLSCALE_250DPS (0x00 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 250 deg/sec | |
#define | ICM20648_GYRO_FULLSCALE_500DPS (0x01 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 500 deg/sec | |
#define | ICM20648_GYRO_FULLSCALE_1000DPS (0x02 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 1000 deg/sec. | |
#define | ICM20648_GYRO_FULLSCALE_2000DPS (0x03 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 2000 deg/sec. | |
#define | ICM20648_GYRO_BW_12100HZ (0x00 << ICM20648_SHIFT_GYRO_DLPCFG) |
Gyro Bandwidth = 12100 Hz. | |
#define | ICM20648_GYRO_BW_360HZ ( (0x07 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 360 Hz | |
#define | ICM20648_GYRO_BW_200HZ ( (0x00 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 200 Hz | |
#define | ICM20648_GYRO_BW_150HZ ( (0x01 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 150 Hz | |
#define | ICM20648_GYRO_BW_120HZ ( (0x02 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 120 Hz | |
#define | ICM20648_GYRO_BW_51HZ ( (0x03 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 51 Hz | |
#define | ICM20648_GYRO_BW_24HZ ( (0x04 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 24 Hz | |
#define | ICM20648_GYRO_BW_12HZ ( (0x05 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 12 Hz | |
#define | ICM20648_GYRO_BW_6HZ ( (0x06 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 6 Hz | |
#define | ICM20648_REG_GYRO_CONFIG_2 (ICM20648_BANK_2 | 0x02) |
Gyroscope Configuration 2 register | |
#define | ICM20648_BIT_GYRO_CTEN 0x38 |
Gyroscope Self-Test Enable bits | |
#define | ICM20648_REG_XG_OFFS_USRH (ICM20648_BANK_2 | 0x03) |
Gyroscope sensor X-axis offset cancellation high byte | |
#define | ICM20648_REG_XG_OFFS_USRL (ICM20648_BANK_2 | 0x04) |
Gyroscope sensor X-axis offset cancellation low byte | |
#define | ICM20648_REG_YG_OFFS_USRH (ICM20648_BANK_2 | 0x05) |
Gyroscope sensor Y-axis offset cancellation high byte | |
#define | ICM20648_REG_YG_OFFS_USRL (ICM20648_BANK_2 | 0x06) |
Gyroscope sensor Y-axis offset cancellation low byte | |
#define | ICM20648_REG_ZG_OFFS_USRH (ICM20648_BANK_2 | 0x07) |
Gyroscope sensor Z-axis offset cancellation high byte | |
#define | ICM20648_REG_ZG_OFFS_USRL (ICM20648_BANK_2 | 0x08) |
Gyroscope sensor Z-axis offset cancellation low byte | |
#define | ICM20648_REG_ODR_ALIGN_EN (ICM20648_BANK_2 | 0x09) |
Output Data Rate start time alignment | |
#define | ICM20648_REG_ACCEL_SMPLRT_DIV_1 (ICM20648_BANK_2 | 0x10) |
Acceleration Sensor Sample Rate Divider 1 register | |
#define | ICM20648_REG_ACCEL_SMPLRT_DIV_2 (ICM20648_BANK_2 | 0x11) |
Acceleration Sensor Sample Rate Divider 2 register | |
#define | ICM20648_REG_ACCEL_INTEL_CTRL (ICM20648_BANK_2 | 0x12) |
Accelerometer Hardware Intelligence Control register | |
#define | ICM20648_BIT_ACCEL_INTEL_EN 0x02 |
Wake-up On Motion enable bit | |
#define | ICM20648_BIT_ACCEL_INTEL_MODE 0x01 |
WOM algorithm selection bit | |
#define | ICM20648_REG_ACCEL_WOM_THR (ICM20648_BANK_2 | 0x13) |
Wake-up On Motion Threshold register | |
#define | ICM20648_REG_ACCEL_CONFIG (ICM20648_BANK_2 | 0x14) |
Accelerometer Configuration register | |
#define | ICM20648_BIT_ACCEL_FCHOICE 0x01 |
Accel Digital Low-Pass Filter enable bit | |
#define | ICM20648_SHIFT_ACCEL_FS 1 |
Accel Full Scale Select bit shift | |
#define | ICM20648_SHIFT_ACCEL_DLPCFG 3 |
Accel DLPF Config bit shift | |
#define | ICM20648_MASK_ACCEL_FULLSCALE 0x06 |
Accel Full Scale Select bitmask | |
#define | ICM20648_MASK_ACCEL_BW 0x39 |
Accel Bandwidth Select bitmask | |
#define | ICM20648_ACCEL_FULLSCALE_2G (0x00 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 2 g | |
#define | ICM20648_ACCEL_FULLSCALE_4G (0x01 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 4 g | |
#define | ICM20648_ACCEL_FULLSCALE_8G (0x02 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 8 g | |
#define | ICM20648_ACCEL_FULLSCALE_16G (0x03 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 16 g. | |
#define | ICM20648_ACCEL_BW_1210HZ (0x00 << ICM20648_SHIFT_ACCEL_DLPCFG) |
Accel Bandwidth = 1210 Hz | |
#define | ICM20648_ACCEL_BW_470HZ ( (0x07 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 470 Hz | |
#define | ICM20648_ACCEL_BW_246HZ ( (0x00 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 246 Hz | |
#define | ICM20648_ACCEL_BW_111HZ ( (0x02 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 111 Hz | |
#define | ICM20648_ACCEL_BW_50HZ ( (0x03 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 50 Hz | |
#define | ICM20648_ACCEL_BW_24HZ ( (0x04 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 24 Hz | |
#define | ICM20648_ACCEL_BW_12HZ ( (0x05 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 12 Hz | |
#define | ICM20648_ACCEL_BW_6HZ ( (0x06 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 6 Hz | |
#define | ICM20648_REG_ACCEL_CONFIG_2 (ICM20648_BANK_2 | 0x15) |
Accelerometer Configuration 2 register | |
#define | ICM20648_BIT_ACCEL_CTEN 0x1C |
Accelerometer Self-Test Enable bits | |
#define | ICM20648_REG_I2C_MST_ODR_CONFIG (ICM20648_BANK_3 | 0x00) |
I2C Master Output Data Rate Configuration register | |
#define | ICM20648_REG_I2C_MST_CTRL (ICM20648_BANK_3 | 0x01) |
I2C Master Control register | |
#define | ICM20648_BIT_I2C_MST_P_NSR 0x10 |
Stop between reads enabling bit | |
#define | ICM20648_REG_I2C_MST_DELAY_CTRL (ICM20648_BANK_3 | 0x02) |
I2C Master Delay Control register | |
#define | ICM20648_BIT_SLV0_DLY_EN 0x01 |
I2C Slave0 Delay Enable bit | |
#define | ICM20648_BIT_SLV1_DLY_EN 0x02 |
I2C Slave1 Delay Enable bit | |
#define | ICM20648_BIT_SLV2_DLY_EN 0x04 |
I2C Slave2 Delay Enable bit | |
#define | ICM20648_BIT_SLV3_DLY_EN 0x08 |
I2C Slave3 Delay Enable bit | |
#define | ICM20648_REG_I2C_SLV0_ADDR (ICM20648_BANK_3 | 0x03) |
I2C Slave0 Physical Address register | |
#define | ICM20648_REG_I2C_SLV0_REG (ICM20648_BANK_3 | 0x04) |
I2C Slave0 Register Address register | |
#define | ICM20648_REG_I2C_SLV0_CTRL (ICM20648_BANK_3 | 0x05) |
I2C Slave0 Control register | |
#define | ICM20648_REG_I2C_SLV0_DO (ICM20648_BANK_3 | 0x06) |
I2C Slave0 Data Out register | |
#define | ICM20648_REG_I2C_SLV1_ADDR (ICM20648_BANK_3 | 0x07) |
I2C Slave1 Physical Address register | |
#define | ICM20648_REG_I2C_SLV1_REG (ICM20648_BANK_3 | 0x08) |
I2C Slave1 Register Address register | |
#define | ICM20648_REG_I2C_SLV1_CTRL (ICM20648_BANK_3 | 0x09) |
I2C Slave1 Control register | |
#define | ICM20648_REG_I2C_SLV1_DO (ICM20648_BANK_3 | 0x0A) |
I2C Slave1 Data Out register | |
#define | ICM20648_REG_I2C_SLV2_ADDR (ICM20648_BANK_3 | 0x0B) |
I2C Slave2 Physical Address register | |
#define | ICM20648_REG_I2C_SLV2_REG (ICM20648_BANK_3 | 0x0C) |
I2C Slave2 Register Address register | |
#define | ICM20648_REG_I2C_SLV2_CTRL (ICM20648_BANK_3 | 0x0D) |
I2C Slave2 Control register | |
#define | ICM20648_REG_I2C_SLV2_DO (ICM20648_BANK_3 | 0x0E) |
I2C Slave2 Data Out register | |
#define | ICM20648_REG_I2C_SLV3_ADDR (ICM20648_BANK_3 | 0x0F) |
I2C Slave3 Physical Address register | |
#define | ICM20648_REG_I2C_SLV3_REG (ICM20648_BANK_3 | 0x10) |
I2C Slave3 Register Address register | |
#define | ICM20648_REG_I2C_SLV3_CTRL (ICM20648_BANK_3 | 0x11) |
I2C Slave3 Control register | |
#define | ICM20648_REG_I2C_SLV3_DO (ICM20648_BANK_3 | 0x12) |
I2C Slave3 Data Out register | |
#define | ICM20648_REG_I2C_SLV4_ADDR (ICM20648_BANK_3 | 0x13) |
I2C Slave4 Physical Address register | |
#define | ICM20648_REG_I2C_SLV4_REG (ICM20648_BANK_3 | 0x14) |
I2C Slave4 Register Address register | |
#define | ICM20648_REG_I2C_SLV4_CTRL (ICM20648_BANK_3 | 0x15) |
I2C Slave4 Control register | |
#define | ICM20648_REG_I2C_SLV4_DO (ICM20648_BANK_3 | 0x16) |
I2C Slave4 Data Out register | |
#define | ICM20648_REG_I2C_SLV4_DI (ICM20648_BANK_3 | 0x17) |
I2C Slave4 Data In register | |
#define | ICM20648_BIT_I2C_SLV_EN 0x80 |
I2C Slave Enable bit | |
#define | ICM20648_BIT_I2C_BYTE_SW 0x40 |
I2C Slave Byte Swap enable bit | |
#define | ICM20648_BIT_I2C_REG_DIS 0x20 |
I2C Slave Do Not Write Register Value bit | |
#define | ICM20648_BIT_I2C_GRP 0x10 |
I2C Slave Group bit | |
#define | ICM20648_BIT_I2C_READ 0x80 |
I2C Slave R/W bit | |
#define | ICM20648_REG_BANK_SEL 0x7F |
Bank Select register | |
#define | ICM20648_DEVICE_ID 0xE0 |
ICM20648 Device ID value | |
#define | ICM20948_DEVICE_ID 0xEA |
ICM20948 Device ID value | |
Macro Definition Documentation
◆ ICM20648_BANK_0
#define ICM20648_BANK_0 (0 << 7) |
Register bank 0.
◆ ICM20648_BANK_1
#define ICM20648_BANK_1 (1 << 7) |
Register bank 1.
◆ ICM20648_BANK_2
#define ICM20648_BANK_2 (2 << 7) |
Register bank 2.
◆ ICM20648_BANK_3
#define ICM20648_BANK_3 (3 << 7) |
Register bank 3.
◆ ICM20648_REG_WHO_AM_I
#define ICM20648_REG_WHO_AM_I (ICM20648_BANK_0 | 0x00) |
Device ID register
◆ ICM20648_REG_USER_CTRL
#define ICM20648_REG_USER_CTRL (ICM20648_BANK_0 | 0x03) |
User control register
◆ ICM20648_BIT_DMP_EN
#define ICM20648_BIT_DMP_EN 0x80 |
DMP enable bit
◆ ICM20648_BIT_FIFO_EN
#define ICM20648_BIT_FIFO_EN 0x40 |
FIFO enable bit
◆ ICM20648_BIT_I2C_MST_EN
#define ICM20648_BIT_I2C_MST_EN 0x20 |
I2C master I/F enable bit
◆ ICM20648_BIT_I2C_IF_DIS
#define ICM20648_BIT_I2C_IF_DIS 0x10 |
Disable I2C, enable SPI bit
◆ ICM20648_BIT_DMP_RST
#define ICM20648_BIT_DMP_RST 0x08 |
DMP module reset bit
◆ ICM20648_BIT_DIAMOND_DMP_RST
#define ICM20648_BIT_DIAMOND_DMP_RST 0x04 |
SRAM module reset bit
◆ ICM20648_REG_LP_CONFIG
#define ICM20648_REG_LP_CONFIG (ICM20648_BANK_0 | 0x05) |
Low Power mode config register
◆ ICM20648_BIT_I2C_MST_CYCLE
#define ICM20648_BIT_I2C_MST_CYCLE 0x40 |
I2C master cycle mode enable
◆ ICM20648_BIT_ACCEL_CYCLE
#define ICM20648_BIT_ACCEL_CYCLE 0x20 |
Accelerometer cycle mode enable
◆ ICM20648_BIT_GYRO_CYCLE
#define ICM20648_BIT_GYRO_CYCLE 0x10 |
Gyroscope cycle mode enable
◆ ICM20648_REG_PWR_MGMT_1
#define ICM20648_REG_PWR_MGMT_1 (ICM20648_BANK_0 | 0x06) |
Power Management 1 register
◆ ICM20648_BIT_H_RESET
#define ICM20648_BIT_H_RESET 0x80 |
Device reset bit
◆ ICM20648_BIT_SLEEP
#define ICM20648_BIT_SLEEP 0x40 |
Sleep mode enable bit
◆ ICM20648_BIT_LP_EN
#define ICM20648_BIT_LP_EN 0x20 |
Low Power feature enable bit
◆ ICM20648_BIT_TEMP_DIS
#define ICM20648_BIT_TEMP_DIS 0x08 |
Temperature sensor disable bit
◆ ICM20648_BIT_CLK_PLL
#define ICM20648_BIT_CLK_PLL 0x01 |
Auto clock source selection setting
◆ ICM20648_REG_PWR_MGMT_2
#define ICM20648_REG_PWR_MGMT_2 (ICM20648_BANK_0 | 0x07) |
Power Management 2 register
◆ ICM20648_BIT_PWR_ACCEL_STBY
#define ICM20648_BIT_PWR_ACCEL_STBY 0x38 |
Disable accelerometer
◆ ICM20648_BIT_PWR_GYRO_STBY
#define ICM20648_BIT_PWR_GYRO_STBY 0x07 |
Disable gyroscope
◆ ICM20648_BIT_PWR_ALL_OFF
#define ICM20648_BIT_PWR_ALL_OFF 0x7F |
Disable both accel and gyro
◆ ICM20648_REG_INT_PIN_CFG
#define ICM20648_REG_INT_PIN_CFG (ICM20648_BANK_0 | 0x0F) |
Interrupt Pin Configuration register
◆ ICM20648_BIT_INT_ACTL
#define ICM20648_BIT_INT_ACTL 0x80 |
Active low setting bit
◆ ICM20648_BIT_INT_OPEN
#define ICM20648_BIT_INT_OPEN 0x40 |
Open collector configuration bit
◆ ICM20648_BIT_INT_LATCH_EN
#define ICM20648_BIT_INT_LATCH_EN 0x20 |
Latch enable bit
◆ ICM20648_REG_INT_ENABLE
#define ICM20648_REG_INT_ENABLE (ICM20648_BANK_0 | 0x10) |
Interrupt Enable register
◆ ICM20648_BIT_WOM_INT_EN
#define ICM20648_BIT_WOM_INT_EN 0x08 |
Wake-up On Motion enable bit
◆ ICM20648_REG_INT_ENABLE_1
#define ICM20648_REG_INT_ENABLE_1 (ICM20648_BANK_0 | 0x11) |
Interrupt Enable 1 register
◆ ICM20648_BIT_RAW_DATA_0_RDY_EN
#define ICM20648_BIT_RAW_DATA_0_RDY_EN 0x01 |
Raw data ready interrupt enable bit
◆ ICM20648_REG_INT_ENABLE_2
#define ICM20648_REG_INT_ENABLE_2 (ICM20648_BANK_0 | 0x12) |
Interrupt Enable 2 register
◆ ICM20648_BIT_FIFO_OVERFLOW_EN_0
#define ICM20648_BIT_FIFO_OVERFLOW_EN_0 0x01 |
FIFO overflow interrupt enable bit
◆ ICM20648_REG_INT_ENABLE_3
#define ICM20648_REG_INT_ENABLE_3 (ICM20648_BANK_0 | 0x13) |
Interrupt Enable 2 register
◆ ICM20648_REG_INT_STATUS
#define ICM20648_REG_INT_STATUS (ICM20648_BANK_0 | 0x19) |
Interrupt Status register
◆ ICM20648_BIT_WOM_INT
#define ICM20648_BIT_WOM_INT 0x08 |
Wake-up on motion interrupt occurred bit
◆ ICM20648_BIT_PLL_RDY
#define ICM20648_BIT_PLL_RDY 0x04 |
PLL ready interrupt occurred bit
◆ ICM20648_REG_INT_STATUS_1
#define ICM20648_REG_INT_STATUS_1 (ICM20648_BANK_0 | 0x1A) |
Interrupt Status 1 register
◆ ICM20648_BIT_RAW_DATA_0_RDY_INT
#define ICM20648_BIT_RAW_DATA_0_RDY_INT 0x01 |
Raw data ready interrupt occurred bit
◆ ICM20648_REG_INT_STATUS_2
#define ICM20648_REG_INT_STATUS_2 (ICM20648_BANK_0 | 0x1B) |
Interrupt Status 2 register
◆ ICM20648_REG_ACCEL_XOUT_H_SH
#define ICM20648_REG_ACCEL_XOUT_H_SH (ICM20648_BANK_0 | 0x2D) |
Accelerometer X-axis data high byte
◆ ICM20648_REG_ACCEL_XOUT_L_SH
#define ICM20648_REG_ACCEL_XOUT_L_SH (ICM20648_BANK_0 | 0x2E) |
Accelerometer X-axis data low byte
◆ ICM20648_REG_ACCEL_YOUT_H_SH
#define ICM20648_REG_ACCEL_YOUT_H_SH (ICM20648_BANK_0 | 0x2F) |
Accelerometer Y-axis data high byte
◆ ICM20648_REG_ACCEL_YOUT_L_SH
#define ICM20648_REG_ACCEL_YOUT_L_SH (ICM20648_BANK_0 | 0x30) |
Accelerometer Y-axis data low byte
◆ ICM20648_REG_ACCEL_ZOUT_H_SH
#define ICM20648_REG_ACCEL_ZOUT_H_SH (ICM20648_BANK_0 | 0x31) |
Accelerometer Z-axis data high byte
◆ ICM20648_REG_ACCEL_ZOUT_L_SH
#define ICM20648_REG_ACCEL_ZOUT_L_SH (ICM20648_BANK_0 | 0x32) |
Accelerometer Z-axis data low byte
◆ ICM20648_REG_GYRO_XOUT_H_SH
#define ICM20648_REG_GYRO_XOUT_H_SH (ICM20648_BANK_0 | 0x33) |
Gyroscope X-axis data high byte
◆ ICM20648_REG_GYRO_XOUT_L_SH
#define ICM20648_REG_GYRO_XOUT_L_SH (ICM20648_BANK_0 | 0x34) |
Gyroscope X-axis data low byte
◆ ICM20648_REG_GYRO_YOUT_H_SH
#define ICM20648_REG_GYRO_YOUT_H_SH (ICM20648_BANK_0 | 0x35) |
Gyroscope Y-axis data high byte
◆ ICM20648_REG_GYRO_YOUT_L_SH
#define ICM20648_REG_GYRO_YOUT_L_SH (ICM20648_BANK_0 | 0x36) |
Gyroscope Y-axis data low byte
◆ ICM20648_REG_GYRO_ZOUT_H_SH
#define ICM20648_REG_GYRO_ZOUT_H_SH (ICM20648_BANK_0 | 0x37) |
Gyroscope Z-axis data high byte
◆ ICM20648_REG_GYRO_ZOUT_L_SH
#define ICM20648_REG_GYRO_ZOUT_L_SH (ICM20648_BANK_0 | 0x38) |
Gyroscope Z-axis data low byte
◆ ICM20648_REG_TEMPERATURE_H
#define ICM20648_REG_TEMPERATURE_H (ICM20648_BANK_0 | 0x39) |
Temperature data high byte
◆ ICM20648_REG_TEMPERATURE_L
#define ICM20648_REG_TEMPERATURE_L (ICM20648_BANK_0 | 0x3A) |
Temperature data low byte
◆ ICM20648_REG_TEMP_CONFIG
#define ICM20648_REG_TEMP_CONFIG (ICM20648_BANK_0 | 0x53) |
Temperature Configuration register
◆ ICM20648_REG_FIFO_EN_1
#define ICM20648_REG_FIFO_EN_1 (ICM20648_BANK_0 | 0x66) |
FIFO Enable 1 register
◆ ICM20648_REG_FIFO_EN_2
#define ICM20648_REG_FIFO_EN_2 (ICM20648_BANK_0 | 0x67) |
FIFO Enable 2 register
◆ ICM20648_BIT_ACCEL_FIFO_EN
#define ICM20648_BIT_ACCEL_FIFO_EN 0x10 |
Enable writing acceleration data to FIFO bit
◆ ICM20648_BITS_GYRO_FIFO_EN
#define ICM20648_BITS_GYRO_FIFO_EN 0x0E |
Enable writing gyroscope data to FIFO bit
◆ ICM20648_REG_FIFO_RST
#define ICM20648_REG_FIFO_RST (ICM20648_BANK_0 | 0x68) |
FIFO Reset register
◆ ICM20648_REG_FIFO_MODE
#define ICM20648_REG_FIFO_MODE (ICM20648_BANK_0 | 0x69) |
FIFO Mode register
◆ ICM20648_REG_FIFO_COUNT_H
#define ICM20648_REG_FIFO_COUNT_H (ICM20648_BANK_0 | 0x70) |
FIFO data count high byte
◆ ICM20648_REG_FIFO_COUNT_L
#define ICM20648_REG_FIFO_COUNT_L (ICM20648_BANK_0 | 0x71) |
FIFO data count low byte
◆ ICM20648_REG_FIFO_R_W
#define ICM20648_REG_FIFO_R_W (ICM20648_BANK_0 | 0x72) |
FIFO Read/Write register
◆ ICM20648_REG_DATA_RDY_STATUS
#define ICM20648_REG_DATA_RDY_STATUS (ICM20648_BANK_0 | 0x74) |
Data Ready Status register
◆ ICM20648_BIT_RAW_DATA_0_RDY
#define ICM20648_BIT_RAW_DATA_0_RDY 0x01 |
Raw Data Ready bit
◆ ICM20648_REG_FIFO_CFG
#define ICM20648_REG_FIFO_CFG (ICM20648_BANK_0 | 0x76) |
FIFO Configuration register
◆ ICM20648_BIT_MULTI_FIFO_CFG
#define ICM20648_BIT_MULTI_FIFO_CFG 0x01 |
Interrupt status for each sensor is required
◆ ICM20648_BIT_SINGLE_FIFO_CFG
#define ICM20648_BIT_SINGLE_FIFO_CFG 0x00 |
Interrupt status for only a single sensor is required
◆ ICM20648_REG_XA_OFFSET_H
#define ICM20648_REG_XA_OFFSET_H (ICM20648_BANK_1 | 0x14) |
Acceleration sensor X-axis offset cancellation high byte
◆ ICM20648_REG_XA_OFFSET_L
#define ICM20648_REG_XA_OFFSET_L (ICM20648_BANK_1 | 0x15) |
Acceleration sensor X-axis offset cancellation low byte
◆ ICM20648_REG_YA_OFFSET_H
#define ICM20648_REG_YA_OFFSET_H (ICM20648_BANK_1 | 0x17) |
Acceleration sensor Y-axis offset cancellation high byte
◆ ICM20648_REG_YA_OFFSET_L
#define ICM20648_REG_YA_OFFSET_L (ICM20648_BANK_1 | 0x18) |
Acceleration sensor Y-axis offset cancellation low byte
◆ ICM20648_REG_ZA_OFFSET_H
#define ICM20648_REG_ZA_OFFSET_H (ICM20648_BANK_1 | 0x1A) |
Acceleration sensor Z-axis offset cancellation high byte
◆ ICM20648_REG_ZA_OFFSET_L
#define ICM20648_REG_ZA_OFFSET_L (ICM20648_BANK_1 | 0x1B) |
Acceleration sensor Z-axis offset cancellation low byte
◆ ICM20648_REG_TIMEBASE_CORR_PLL
#define ICM20648_REG_TIMEBASE_CORR_PLL (ICM20648_BANK_1 | 0x28) |
PLL Timebase Correction register
◆ ICM20648_REG_GYRO_SMPLRT_DIV
#define ICM20648_REG_GYRO_SMPLRT_DIV (ICM20648_BANK_2 | 0x00) |
Gyroscope Sample Rate Divider register
◆ ICM20648_REG_GYRO_CONFIG_1
#define ICM20648_REG_GYRO_CONFIG_1 (ICM20648_BANK_2 | 0x01) |
Gyroscope Configuration 1 register
◆ ICM20648_BIT_GYRO_FCHOICE
#define ICM20648_BIT_GYRO_FCHOICE 0x01 |
Gyro Digital Low-Pass Filter enable bit
◆ ICM20648_SHIFT_GYRO_FS_SEL
#define ICM20648_SHIFT_GYRO_FS_SEL 1 |
Gyro Full Scale Select bit shift
◆ ICM20648_SHIFT_GYRO_DLPCFG
#define ICM20648_SHIFT_GYRO_DLPCFG 3 |
Gyro DLPF Config bit shift
◆ ICM20648_MASK_GYRO_FULLSCALE
#define ICM20648_MASK_GYRO_FULLSCALE 0x06 |
Gyro Full Scale Select bitmask
◆ ICM20648_MASK_GYRO_BW
#define ICM20648_MASK_GYRO_BW 0x39 |
Gyro Bandwidth Select bitmask
◆ ICM20648_GYRO_FULLSCALE_250DPS
#define ICM20648_GYRO_FULLSCALE_250DPS (0x00 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 250 deg/sec
◆ ICM20648_GYRO_FULLSCALE_500DPS
#define ICM20648_GYRO_FULLSCALE_500DPS (0x01 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 500 deg/sec
◆ ICM20648_GYRO_FULLSCALE_1000DPS
#define ICM20648_GYRO_FULLSCALE_1000DPS (0x02 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 1000 deg/sec.
◆ ICM20648_GYRO_FULLSCALE_2000DPS
#define ICM20648_GYRO_FULLSCALE_2000DPS (0x03 << ICM20648_SHIFT_GYRO_FS_SEL) |
Gyro Full Scale = 2000 deg/sec.
◆ ICM20648_GYRO_BW_12100HZ
#define ICM20648_GYRO_BW_12100HZ (0x00 << ICM20648_SHIFT_GYRO_DLPCFG) |
Gyro Bandwidth = 12100 Hz.
◆ ICM20648_GYRO_BW_360HZ
#define ICM20648_GYRO_BW_360HZ ( (0x07 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 360 Hz
◆ ICM20648_GYRO_BW_200HZ
#define ICM20648_GYRO_BW_200HZ ( (0x00 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 200 Hz
◆ ICM20648_GYRO_BW_150HZ
#define ICM20648_GYRO_BW_150HZ ( (0x01 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 150 Hz
◆ ICM20648_GYRO_BW_120HZ
#define ICM20648_GYRO_BW_120HZ ( (0x02 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 120 Hz
◆ ICM20648_GYRO_BW_51HZ
#define ICM20648_GYRO_BW_51HZ ( (0x03 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 51 Hz
◆ ICM20648_GYRO_BW_24HZ
#define ICM20648_GYRO_BW_24HZ ( (0x04 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 24 Hz
◆ ICM20648_GYRO_BW_12HZ
#define ICM20648_GYRO_BW_12HZ ( (0x05 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 12 Hz
◆ ICM20648_GYRO_BW_6HZ
#define ICM20648_GYRO_BW_6HZ ( (0x06 << ICM20648_SHIFT_GYRO_DLPCFG) | ICM20648_BIT_GYRO_FCHOICE) |
Gyro Bandwidth = 6 Hz
◆ ICM20648_REG_GYRO_CONFIG_2
#define ICM20648_REG_GYRO_CONFIG_2 (ICM20648_BANK_2 | 0x02) |
Gyroscope Configuration 2 register
◆ ICM20648_BIT_GYRO_CTEN
#define ICM20648_BIT_GYRO_CTEN 0x38 |
Gyroscope Self-Test Enable bits
◆ ICM20648_REG_XG_OFFS_USRH
#define ICM20648_REG_XG_OFFS_USRH (ICM20648_BANK_2 | 0x03) |
Gyroscope sensor X-axis offset cancellation high byte
◆ ICM20648_REG_XG_OFFS_USRL
#define ICM20648_REG_XG_OFFS_USRL (ICM20648_BANK_2 | 0x04) |
Gyroscope sensor X-axis offset cancellation low byte
◆ ICM20648_REG_YG_OFFS_USRH
#define ICM20648_REG_YG_OFFS_USRH (ICM20648_BANK_2 | 0x05) |
Gyroscope sensor Y-axis offset cancellation high byte
◆ ICM20648_REG_YG_OFFS_USRL
#define ICM20648_REG_YG_OFFS_USRL (ICM20648_BANK_2 | 0x06) |
Gyroscope sensor Y-axis offset cancellation low byte
◆ ICM20648_REG_ZG_OFFS_USRH
#define ICM20648_REG_ZG_OFFS_USRH (ICM20648_BANK_2 | 0x07) |
Gyroscope sensor Z-axis offset cancellation high byte
◆ ICM20648_REG_ZG_OFFS_USRL
#define ICM20648_REG_ZG_OFFS_USRL (ICM20648_BANK_2 | 0x08) |
Gyroscope sensor Z-axis offset cancellation low byte
◆ ICM20648_REG_ODR_ALIGN_EN
#define ICM20648_REG_ODR_ALIGN_EN (ICM20648_BANK_2 | 0x09) |
Output Data Rate start time alignment
◆ ICM20648_REG_ACCEL_SMPLRT_DIV_1
#define ICM20648_REG_ACCEL_SMPLRT_DIV_1 (ICM20648_BANK_2 | 0x10) |
Acceleration Sensor Sample Rate Divider 1 register
◆ ICM20648_REG_ACCEL_SMPLRT_DIV_2
#define ICM20648_REG_ACCEL_SMPLRT_DIV_2 (ICM20648_BANK_2 | 0x11) |
Acceleration Sensor Sample Rate Divider 2 register
◆ ICM20648_REG_ACCEL_INTEL_CTRL
#define ICM20648_REG_ACCEL_INTEL_CTRL (ICM20648_BANK_2 | 0x12) |
Accelerometer Hardware Intelligence Control register
◆ ICM20648_BIT_ACCEL_INTEL_EN
#define ICM20648_BIT_ACCEL_INTEL_EN 0x02 |
Wake-up On Motion enable bit
◆ ICM20648_BIT_ACCEL_INTEL_MODE
#define ICM20648_BIT_ACCEL_INTEL_MODE 0x01 |
WOM algorithm selection bit
◆ ICM20648_REG_ACCEL_WOM_THR
#define ICM20648_REG_ACCEL_WOM_THR (ICM20648_BANK_2 | 0x13) |
Wake-up On Motion Threshold register
◆ ICM20648_REG_ACCEL_CONFIG
#define ICM20648_REG_ACCEL_CONFIG (ICM20648_BANK_2 | 0x14) |
Accelerometer Configuration register
◆ ICM20648_BIT_ACCEL_FCHOICE
#define ICM20648_BIT_ACCEL_FCHOICE 0x01 |
Accel Digital Low-Pass Filter enable bit
◆ ICM20648_SHIFT_ACCEL_FS
#define ICM20648_SHIFT_ACCEL_FS 1 |
Accel Full Scale Select bit shift
◆ ICM20648_SHIFT_ACCEL_DLPCFG
#define ICM20648_SHIFT_ACCEL_DLPCFG 3 |
Accel DLPF Config bit shift
◆ ICM20648_MASK_ACCEL_FULLSCALE
#define ICM20648_MASK_ACCEL_FULLSCALE 0x06 |
Accel Full Scale Select bitmask
◆ ICM20648_MASK_ACCEL_BW
#define ICM20648_MASK_ACCEL_BW 0x39 |
Accel Bandwidth Select bitmask
◆ ICM20648_ACCEL_FULLSCALE_2G
#define ICM20648_ACCEL_FULLSCALE_2G (0x00 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 2 g
◆ ICM20648_ACCEL_FULLSCALE_4G
#define ICM20648_ACCEL_FULLSCALE_4G (0x01 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 4 g
◆ ICM20648_ACCEL_FULLSCALE_8G
#define ICM20648_ACCEL_FULLSCALE_8G (0x02 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 8 g
◆ ICM20648_ACCEL_FULLSCALE_16G
#define ICM20648_ACCEL_FULLSCALE_16G (0x03 << ICM20648_SHIFT_ACCEL_FS) |
Accel Full Scale = 16 g.
◆ ICM20648_ACCEL_BW_1210HZ
#define ICM20648_ACCEL_BW_1210HZ (0x00 << ICM20648_SHIFT_ACCEL_DLPCFG) |
Accel Bandwidth = 1210 Hz
◆ ICM20648_ACCEL_BW_470HZ
#define ICM20648_ACCEL_BW_470HZ ( (0x07 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 470 Hz
◆ ICM20648_ACCEL_BW_246HZ
#define ICM20648_ACCEL_BW_246HZ ( (0x00 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 246 Hz
◆ ICM20648_ACCEL_BW_111HZ
#define ICM20648_ACCEL_BW_111HZ ( (0x02 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 111 Hz
◆ ICM20648_ACCEL_BW_50HZ
#define ICM20648_ACCEL_BW_50HZ ( (0x03 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 50 Hz
◆ ICM20648_ACCEL_BW_24HZ
#define ICM20648_ACCEL_BW_24HZ ( (0x04 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 24 Hz
◆ ICM20648_ACCEL_BW_12HZ
#define ICM20648_ACCEL_BW_12HZ ( (0x05 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 12 Hz
◆ ICM20648_ACCEL_BW_6HZ
#define ICM20648_ACCEL_BW_6HZ ( (0x06 << ICM20648_SHIFT_ACCEL_DLPCFG) | ICM20648_BIT_ACCEL_FCHOICE) |
Accel Bandwidth = 6 Hz
◆ ICM20648_REG_ACCEL_CONFIG_2
#define ICM20648_REG_ACCEL_CONFIG_2 (ICM20648_BANK_2 | 0x15) |
Accelerometer Configuration 2 register
◆ ICM20648_BIT_ACCEL_CTEN
#define ICM20648_BIT_ACCEL_CTEN 0x1C |
Accelerometer Self-Test Enable bits
◆ ICM20648_REG_I2C_MST_ODR_CONFIG
#define ICM20648_REG_I2C_MST_ODR_CONFIG (ICM20648_BANK_3 | 0x00) |
I2C Master Output Data Rate Configuration register
◆ ICM20648_REG_I2C_MST_CTRL
#define ICM20648_REG_I2C_MST_CTRL (ICM20648_BANK_3 | 0x01) |
I2C Master Control register
◆ ICM20648_BIT_I2C_MST_P_NSR
#define ICM20648_BIT_I2C_MST_P_NSR 0x10 |
Stop between reads enabling bit
◆ ICM20648_REG_I2C_MST_DELAY_CTRL
#define ICM20648_REG_I2C_MST_DELAY_CTRL (ICM20648_BANK_3 | 0x02) |
I2C Master Delay Control register
◆ ICM20648_BIT_SLV0_DLY_EN
#define ICM20648_BIT_SLV0_DLY_EN 0x01 |
I2C Slave0 Delay Enable bit
◆ ICM20648_BIT_SLV1_DLY_EN
#define ICM20648_BIT_SLV1_DLY_EN 0x02 |
I2C Slave1 Delay Enable bit
◆ ICM20648_BIT_SLV2_DLY_EN
#define ICM20648_BIT_SLV2_DLY_EN 0x04 |
I2C Slave2 Delay Enable bit
◆ ICM20648_BIT_SLV3_DLY_EN
#define ICM20648_BIT_SLV3_DLY_EN 0x08 |
I2C Slave3 Delay Enable bit
◆ ICM20648_REG_I2C_SLV0_ADDR
#define ICM20648_REG_I2C_SLV0_ADDR (ICM20648_BANK_3 | 0x03) |
I2C Slave0 Physical Address register
◆ ICM20648_REG_I2C_SLV0_REG
#define ICM20648_REG_I2C_SLV0_REG (ICM20648_BANK_3 | 0x04) |
I2C Slave0 Register Address register
◆ ICM20648_REG_I2C_SLV0_CTRL
#define ICM20648_REG_I2C_SLV0_CTRL (ICM20648_BANK_3 | 0x05) |
I2C Slave0 Control register
◆ ICM20648_REG_I2C_SLV0_DO
#define ICM20648_REG_I2C_SLV0_DO (ICM20648_BANK_3 | 0x06) |
I2C Slave0 Data Out register
◆ ICM20648_REG_I2C_SLV1_ADDR
#define ICM20648_REG_I2C_SLV1_ADDR (ICM20648_BANK_3 | 0x07) |
I2C Slave1 Physical Address register
◆ ICM20648_REG_I2C_SLV1_REG
#define ICM20648_REG_I2C_SLV1_REG (ICM20648_BANK_3 | 0x08) |
I2C Slave1 Register Address register
◆ ICM20648_REG_I2C_SLV1_CTRL
#define ICM20648_REG_I2C_SLV1_CTRL (ICM20648_BANK_3 | 0x09) |
I2C Slave1 Control register
◆ ICM20648_REG_I2C_SLV1_DO
#define ICM20648_REG_I2C_SLV1_DO (ICM20648_BANK_3 | 0x0A) |
I2C Slave1 Data Out register
◆ ICM20648_REG_I2C_SLV2_ADDR
#define ICM20648_REG_I2C_SLV2_ADDR (ICM20648_BANK_3 | 0x0B) |
I2C Slave2 Physical Address register
◆ ICM20648_REG_I2C_SLV2_REG
#define ICM20648_REG_I2C_SLV2_REG (ICM20648_BANK_3 | 0x0C) |
I2C Slave2 Register Address register
◆ ICM20648_REG_I2C_SLV2_CTRL
#define ICM20648_REG_I2C_SLV2_CTRL (ICM20648_BANK_3 | 0x0D) |
I2C Slave2 Control register
◆ ICM20648_REG_I2C_SLV2_DO
#define ICM20648_REG_I2C_SLV2_DO (ICM20648_BANK_3 | 0x0E) |
I2C Slave2 Data Out register
◆ ICM20648_REG_I2C_SLV3_ADDR
#define ICM20648_REG_I2C_SLV3_ADDR (ICM20648_BANK_3 | 0x0F) |
I2C Slave3 Physical Address register
◆ ICM20648_REG_I2C_SLV3_REG
#define ICM20648_REG_I2C_SLV3_REG (ICM20648_BANK_3 | 0x10) |
I2C Slave3 Register Address register
◆ ICM20648_REG_I2C_SLV3_CTRL
#define ICM20648_REG_I2C_SLV3_CTRL (ICM20648_BANK_3 | 0x11) |
I2C Slave3 Control register
◆ ICM20648_REG_I2C_SLV3_DO
#define ICM20648_REG_I2C_SLV3_DO (ICM20648_BANK_3 | 0x12) |
I2C Slave3 Data Out register
◆ ICM20648_REG_I2C_SLV4_ADDR
#define ICM20648_REG_I2C_SLV4_ADDR (ICM20648_BANK_3 | 0x13) |
I2C Slave4 Physical Address register
◆ ICM20648_REG_I2C_SLV4_REG
#define ICM20648_REG_I2C_SLV4_REG (ICM20648_BANK_3 | 0x14) |
I2C Slave4 Register Address register
◆ ICM20648_REG_I2C_SLV4_CTRL
#define ICM20648_REG_I2C_SLV4_CTRL (ICM20648_BANK_3 | 0x15) |
I2C Slave4 Control register
◆ ICM20648_REG_I2C_SLV4_DO
#define ICM20648_REG_I2C_SLV4_DO (ICM20648_BANK_3 | 0x16) |
I2C Slave4 Data Out register
◆ ICM20648_REG_I2C_SLV4_DI
#define ICM20648_REG_I2C_SLV4_DI (ICM20648_BANK_3 | 0x17) |
I2C Slave4 Data In register
◆ ICM20648_BIT_I2C_SLV_EN
#define ICM20648_BIT_I2C_SLV_EN 0x80 |
I2C Slave Enable bit
◆ ICM20648_BIT_I2C_BYTE_SW
#define ICM20648_BIT_I2C_BYTE_SW 0x40 |
I2C Slave Byte Swap enable bit
◆ ICM20648_BIT_I2C_REG_DIS
#define ICM20648_BIT_I2C_REG_DIS 0x20 |
I2C Slave Do Not Write Register Value bit
◆ ICM20648_BIT_I2C_GRP
#define ICM20648_BIT_I2C_GRP 0x10 |
I2C Slave Group bit
◆ ICM20648_BIT_I2C_READ
#define ICM20648_BIT_I2C_READ 0x80 |
I2C Slave R/W bit
◆ ICM20648_REG_BANK_SEL
#define ICM20648_REG_BANK_SEL 0x7F |
Bank Select register
◆ ICM20648_DEVICE_ID
#define ICM20648_DEVICE_ID 0xE0 |
ICM20648 Device ID value
◆ ICM20948_DEVICE_ID
#define ICM20948_DEVICE_ID 0xEA |
ICM20948 Device ID value