WFM API messages.

Data Structures
struct	sl_wfx_set_mac_address_req_body_t
	Request message body for sl_wfx_set_mac_address_req_t .

struct	sl_wfx_set_mac_address_req_t
	Request message to set MAC address of the interface.

struct	sl_wfx_set_mac_address_cnf_body_t
	Confirmation message body for sl_wfx_set_mac_address_cnf_t .

struct	sl_wfx_set_mac_address_cnf_t
	Confirmation message for sl_wfx_set_mac_address_req_t .

struct	sl_wfx_connect_req_body_t
	Request message body for sl_wfx_connect_req_t .

struct	sl_wfx_connect_req_t
	Request message for connecting to a Wi-Fi network.

struct	sl_wfx_connect_cnf_body_t
	Confirmation message body for sl_wfx_connect_cnf_t .

struct	sl_wfx_connect_cnf_t
	Confirmation message for sl_wfx_connect_req_t .

struct	sl_wfx_connect_ind_body_t
	Indication message body for sl_wfx_connect_ind_t .

struct	sl_wfx_connect_ind_t
	Indication message used to signal the completion of a connection operation.

struct	sl_wfx_disconnect_cnf_body_t
	Confirmation message body for sl_wfx_disconnect_cnf_t .

struct	sl_wfx_disconnect_cnf_t
	Confirmation message for sl_wfx_disconnect_req_t .

struct	sl_wfx_disconnect_ind_body_t
	Indication message body for sl_wfx_disconnect_ind_t .

struct	sl_wfx_disconnect_ind_t
	Indication message used to signal the completion of a disconnection operation.

struct	sl_wfx_get_signal_strength_cnf_body_t
	Confirmation message body for sl_wfx_get_signal_strength_cnf_t .

struct	sl_wfx_get_signal_strength_cnf_t
	Confirmation message for sl_wfx_get_signal_strength_req_t .

struct	sl_wfx_set_pm_mode_req_body_t
	Request message body for sl_wfx_set_pm_mode_req_t .

struct	sl_wfx_set_pm_mode_req_t
	Request message for setting the power management mode of the device.

struct	sl_wfx_set_pm_mode_cnf_body_t
	Confirmation message body for sl_wfx_set_pm_mode_cnf_t .

struct	sl_wfx_set_pm_mode_cnf_t
	Confirmation message for sl_wfx_set_pm_mode_req_t .

struct	sl_wfx_start_ap_req_body_t
	Request message body for sl_wfx_start_ap_req_t .

struct	sl_wfx_start_ap_req_t
	Request message for starting a Wi-Fi network.

struct	sl_wfx_start_ap_cnf_body_t
	Confirmation message body for sl_wfx_start_ap_cnf_t .

struct	sl_wfx_start_ap_cnf_t
	Confirmation message for sl_wfx_start_ap_req_t .

struct	sl_wfx_start_ap_ind_body_t
	Indication message body for sl_wfx_start_ap_ind_t .

struct	sl_wfx_start_ap_ind_t
	Indication message used to signal the completion of a start request.

struct	sl_wfx_update_ap_req_body_t
	Request message body for sl_wfx_update_ap_req_t .

struct	sl_wfx_update_ap_req_t
	Request message for updating parameters of the started Wi-Fi network.

struct	sl_wfx_update_ap_cnf_body_t
	Confirmation message body for sl_wfx_update_ap_cnf_t .

struct	sl_wfx_update_ap_cnf_t
	Confirmation message for sl_wfx_update_ap_req_t .

struct	sl_wfx_stop_ap_cnf_body_t
	Confirmation message body for sl_wfx_stop_ap_cnf_t .

struct	sl_wfx_stop_ap_cnf_t
	Confirmation message for sl_wfx_stop_ap_req_t .

struct	sl_wfx_ap_client_connected_ind_body_t
	Indication message body for sl_wfx_ap_client_connected_ind_t .

struct	sl_wfx_ap_client_connected_ind_t
	Indication message used to signal a connected station.

struct	sl_wfx_ap_client_rejected_ind_body_t
	Indication message body for sl_wfx_ap_client_rejected_ind_t .

struct	sl_wfx_ap_client_rejected_ind_t
	Indication message used to signal a rejected connection attempt from a station.

struct	sl_wfx_disconnect_ap_client_req_body_t
	Request message body for sl_wfx_disconnect_ap_client_req_t .

struct	sl_wfx_disconnect_ap_client_req_t
	Request message for disconnecting a client from the started Wi-Fi network.

struct	sl_wfx_disconnect_ap_client_cnf_body_t
	Confirmation message body for sl_wfx_disconnect_ap_client_cnf_t .

struct	sl_wfx_disconnect_ap_client_cnf_t
	Confirmation message for sl_wfx_disconnect_ap_client_req_t .

struct	sl_wfx_ap_client_disconnected_ind_body_t
	Indication message body for sl_wfx_ap_client_disconnected_ind_t .

struct	sl_wfx_ap_client_disconnected_ind_t
	Indication message used to signal a disconnected station.

struct	sl_wfx_send_frame_req_body_t
	Request message body for sl_wfx_send_frame_req_t .

struct	sl_wfx_send_frame_req_t
	Request message for sending a packet to the network.

struct	sl_wfx_send_frame_cnf_body_t
	Confirmation message body for sl_wfx_send_frame_cnf_t .

struct	sl_wfx_send_frame_cnf_t
	Confirmation message for sl_wfx_send_frame_req_t .

struct	sl_wfx_received_ind_body_t
	Indication message body for sl_wfx_received_ind_t .

struct	sl_wfx_received_ind_t
	Indication message used to signal a received packet.

struct	sl_wfx_start_scan_req_body_t
	Request message body for sl_wfx_start_scan_req_t .

struct	sl_wfx_start_scan_req_t
	Request message for starting a scan to detect near-by access points.

struct	sl_wfx_start_scan_cnf_body_t
	Confirmation message body for sl_wfx_start_scan_cnf_t .

struct	sl_wfx_start_scan_cnf_t
	Confirmation message for sl_wfx_start_scan_req_t .

struct	sl_wfx_stop_scan_cnf_body_t
	Confirmation message body for sl_wfx_stop_scan_cnf_t .

struct	sl_wfx_stop_scan_cnf_t
	Confirmation message for sl_wfx_stop_scan_req_t .

struct	sl_wfx_scan_result_ind_body_t
	Indication message body for sl_wfx_scan_result_ind_t .

struct	sl_wfx_scan_result_ind_t
	Indication message used to signal an access point has been detected.

struct	sl_wfx_scan_complete_ind_body_t
	Indication message body for sl_wfx_scan_complete_ind_t .

struct	sl_wfx_scan_complete_ind_t
	Indication message used to signal a scan was completed.

struct	sl_wfx_join_ibss_req_body_t
	Request message body for sl_wfx_join_ibss_req_t .

struct	sl_wfx_join_ibss_req_t
	Request message for connecting to or starting an IBSS network.

struct	sl_wfx_join_ibss_cnf_body_t
	Confirmation message body for sl_wfx_join_ibss_cnf_t .

struct	sl_wfx_join_ibss_cnf_t
	Confirmation message for sl_wfx_join_ibss_req_t .

struct	sl_wfx_join_ibss_ind_body_t
	Indication message body for sl_wfx_join_ibss_ind_t .

struct	sl_wfx_join_ibss_ind_t
	Indication message used to signal the completion of a join request.

struct	sl_wfx_leave_ibss_cnf_body_t
	Confirmation message body for sl_wfx_leave_ibss_cnf_t .

struct	sl_wfx_leave_ibss_cnf_t
	Confirmation message for sl_wfx_leave_ibss_req_t .

struct	sl_wfx_add_multicast_addr_req_body_t
	Request message body for sl_wfx_add_multicast_addr_req_t .

struct	sl_wfx_add_multicast_addr_req_t
	Request message for adding a multicast address to the multicast filter whitelist.

struct	sl_wfx_add_multicast_addr_cnf_body_t
	Confirmation message body for sl_wfx_add_multicast_addr_cnf_t .

struct	sl_wfx_add_multicast_addr_cnf_t
	Confirmation message for sl_wfx_add_multicast_addr_req_t .

struct	sl_wfx_remove_multicast_addr_req_body_t
	Request message body for sl_wfx_remove_multicast_addr_req_t .

struct	sl_wfx_remove_multicast_addr_req_t
	Request message for removing a multicast address from the multicast filter whitelist.

struct	sl_wfx_remove_multicast_addr_cnf_body_t
	Confirmation message body for sl_wfx_remove_multicast_addr_cnf_t .

struct	sl_wfx_remove_multicast_addr_cnf_t
	Confirmation message for sl_wfx_remove_multicast_addr_req_t .

struct	sl_wfx_set_max_ap_client_count_req_body_t
	Request message body for sl_wfx_set_max_ap_client_count_req_t .

struct	sl_wfx_set_max_ap_client_count_req_t
	Request message for setting the maximum number of connected clients.

struct	sl_wfx_set_max_ap_client_count_cnf_body_t
	Confirmation message body for sl_wfx_set_max_ap_client_count_cnf_t .

struct	sl_wfx_set_max_ap_client_count_cnf_t
	Confirmation message for sl_wfx_set_max_ap_client_count_req_t .

struct	sl_wfx_set_max_ap_client_inactivity_req_body_t
	Request message body for sl_wfx_set_max_ap_client_inactivity_req_t .

struct	sl_wfx_set_max_ap_client_inactivity_req_t
	Request message for setting the maximum number of connected clients.

struct	sl_wfx_set_max_ap_client_inactivity_cnf_body_t
	Confirmation message body for sl_wfx_set_max_ap_client_count_cnf_t .

struct	sl_wfx_set_max_ap_client_inactivity_cnf_t
	Confirmation message for sl_wfx_set_max_ap_client_inactivity_req_t .

struct	sl_wfx_set_roam_parameters_req_body_t
	Request message body for sl_wfx_set_roam_parameters_req_t .

struct	sl_wfx_set_roam_parameters_req_t
	Request message for setting the roaming parameters.

struct	sl_wfx_set_roam_parameters_cnf_body_t
	Confirmation message body for sl_wfx_set_roam_parameters_cnf_t .

struct	sl_wfx_set_roam_parameters_cnf_t
	Confirmation message for sl_wfx_set_roam_parameters_req_t .

struct	sl_wfx_set_tx_rate_parameters_req_body_t
	Request message body for sl_wfx_set_tx_rate_parameters_req_t .

struct	sl_wfx_set_tx_rate_parameters_req_t
	Request message for setting the TX rate set parameters.

struct	sl_wfx_set_tx_rate_parameters_cnf_body_t
	Confirmation message body for sl_wfx_set_tx_rate_parameters_cnf_t .

struct	sl_wfx_set_tx_rate_parameters_cnf_t
	Confirmation message for sl_wfx_set_tx_rate_parameters_req_t .

struct	sl_wfx_set_arp_ip_address_req_body_t
	Request message body for sl_wfx_set_arp_ip_address_req_t .

struct	sl_wfx_set_arp_ip_address_req_t
	Request message for setting the Address Resolution Protocol (ARP) offloading state.

struct	sl_wfx_set_arp_ip_address_cnf_body_t
	Confirmation message body for sl_wfx_set_arp_ip_address_cnf_t .

struct	sl_wfx_set_arp_ip_address_cnf_t
	Confirmation message for sl_wfx_set_arp_ip_address_req_t .

struct	sl_wfx_set_ns_ip_address_req_body_t
	Request message body for sl_wfx_set_ns_ip_address_req_t .

struct	sl_wfx_set_ns_ip_address_req_t
	Request message for setting the Neighbor Discovery Protocol (NDP) offloading state.

struct	sl_wfx_set_ns_ip_address_cnf_body_t
	Confirmation message body for sl_wfx_set_ns_ip_address_cnf_t .

struct	sl_wfx_set_ns_ip_address_cnf_t
	Confirmation message for sl_wfx_set_ns_ip_address_req_t .

struct	sl_wfx_set_broadcast_filter_req_body_t
	Request message body for sl_wfx_set_broadcast_filter_req_t .

struct	sl_wfx_set_broadcast_filter_req_t
	Request message for setting broadcast filter state.

struct	sl_wfx_set_broadcast_filter_cnf_body_t
	Confirmation message body for sl_wfx_set_broadcast_filter_cnf_t .

struct	sl_wfx_set_broadcast_filter_cnf_t
	Confirmation message for sl_wfx_set_broadcast_filter_req_t .

struct	sl_wfx_set_scan_parameters_req_body_t
	Request message body for sl_wfx_set_scan_parameters_req_t .

struct	sl_wfx_set_scan_parameters_req_t
	Request message for setting scan parameters.

struct	sl_wfx_set_scan_parameters_cnf_body_t
	Confirmation message body for sl_wfx_set_scan_parameters_cnf_t .

struct	sl_wfx_set_scan_parameters_cnf_t
	Confirmation message for sl_wfx_set_scan_parameters_req_t .

struct	sl_wfx_set_unicast_filter_req_body_t
	Request message body for sl_wfx_set_unicast_filter_req_t .

struct	sl_wfx_set_unicast_filter_req_t
	Request message for setting unicast filter state.

struct	sl_wfx_set_unicast_filter_cnf_body_t
	Confirmation message body for sl_wfx_set_unicast_filter_cnf_t .

struct	sl_wfx_set_unicast_filter_cnf_t
	Confirmation message for sl_wfx_set_unicast_filter_req_t .

struct	sl_wfx_add_whitelist_addr_req_body_t
	Request message body for sl_wfx_add_whitelist_addr_req_t .

struct	sl_wfx_add_whitelist_addr_req_t
	Request message for adding a MAC address to the device whitelist.

struct	sl_wfx_add_whitelist_addr_cnf_body_t
	Confirmation message body for sl_wfx_add_whitelist_addr_cnf_t .

struct	sl_wfx_add_whitelist_addr_cnf_t
	Confirmation message for sl_wfx_add_whitelist_addr_req_t .

struct	sl_wfx_add_blacklist_addr_req_body_t
	Request message body for sl_wfx_add_blacklist_addr_req_t .

struct	sl_wfx_add_blacklist_addr_req_t
	Request message for adding a MAC address to the device blacklist.

struct	sl_wfx_add_blacklist_addr_cnf_body_t
	Confirmation message body for sl_wfx_add_blacklist_addr_cnf_t .

struct	sl_wfx_add_blacklist_addr_cnf_t
	Confirmation message for sl_wfx_add_blacklist_addr_req_t .

struct	sl_wfx_set_max_tx_power_req_body_t
	Request message body for sl_wfx_set_max_tx_power_req_t .

struct	sl_wfx_set_max_tx_power_req_t
	Request message for setting the maximum transmit power of the device.

struct	sl_wfx_set_max_tx_power_cnf_body_t
	Confirmation message body for sl_wfx_set_max_tx_power_cnf_t .

struct	sl_wfx_set_max_tx_power_cnf_t
	Confirmation message for sl_wfx_set_max_tx_power_req_t .

struct	sl_wfx_get_max_tx_power_cnf_body_t
	Confirmation message body for sl_wfx_get_max_tx_power_cnf_t .

struct	sl_wfx_get_max_tx_power_cnf_t
	Confirmation message for sl_wfx_get_max_tx_power_req_t .

struct	sl_wfx_get_pmk_cnf_body_t
	Confirmation message body for sl_wfx_get_pmk_cnf_t .

struct	sl_wfx_get_pmk_cnf_t
	Confirmation message for sl_wfx_get_pmk_req_t .

struct	sl_wfx_get_ap_client_signal_strength_req_body_t
	Request message body for sl_wfx_get_ap_client_signal_strength_req_t .

struct	sl_wfx_get_ap_client_signal_strength_req_t
	Request message for retrieving the signal strength of a client of the started Wi-Fi network.

struct	sl_wfx_get_ap_client_signal_strength_cnf_body_t
	Confirmation message body for sl_wfx_get_ap_client_signal_strength_cnf_t .

struct	sl_wfx_get_ap_client_signal_strength_cnf_t
	Confirmation message for sl_wfx_get_ap_client_signal_strength_cnf_t .

struct	sl_wfx_disconnect_req_t
	Request message for disconnecting from a Wi-Fi network.

struct	sl_wfx_get_signal_strength_req_t
	Request message for retrieving the signal strength of connection.

struct	sl_wfx_stop_ap_req_t
	Request message for stopping the started Wi-Fi network.

struct	sl_wfx_stop_ap_ind_t
	Indication message used to signal the completion of a stop operation.

struct	sl_wfx_stop_scan_req_t
	Request message for stopping an ongoing scan.

struct	sl_wfx_leave_ibss_req_t
	Request message for disconnecting from an IBSS network.

struct	sl_wfx_leave_ibss_ind_t
	Indication message used to signal the completion of a disconnect operation.

struct	sl_wfx_get_max_tx_power_req_t
	Request message for getting the maximum transmit power.

struct	sl_wfx_get_pmk_req_t
	Request message for getting the Pairwise Master Key (PMK).

Detailed Description

WFM API messages.

Data Structure Documentation

◆ sl_wfx_set_mac_address_req_body_t

struct sl_wfx_set_mac_address_req_body_t

Request message body for sl_wfx_set_mac_address_req_t .

Field	Default value	Reset to default value
MAC address	device dependent	when device reset

Definition at line 697 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac_addr[6]	MAC address of the interface.
uint16_t	reserved	Reserved, set to zero.

◆ sl_wfx_set_mac_address_req_t

struct sl_wfx_set_mac_address_req_t

Request message to set MAC address of the interface.

The host can use this request to set the MAC address of an interface. If not set, the device will use a built-in MAC address. Note that if multiple interfaces are used, the MAC address MUST be different on each interface.

Interface mode	Request allowed
idle	Yes
station	No
AP	No
IBSS	No

Definition at line 719 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_mac_address_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_mac_address_cnf_body_t

struct sl_wfx_set_mac_address_cnf_body_t

Confirmation message body for sl_wfx_set_mac_address_cnf_t .

Definition at line 729 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_mac_address_cnf_t

struct sl_wfx_set_mac_address_cnf_t

Confirmation message for sl_wfx_set_mac_address_req_t .

Definition at line 743 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_mac_address_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_connect_req_body_t

struct sl_wfx_connect_req_body_t

Request message body for sl_wfx_connect_req_t .

Definition at line 753 of file wfm_cmd_api.h .

Data Fields
uint8_t	bssid[6]	Basic Service Set Identifier (BSSID) of the Access Point. broadcast address : The device will connect to any matching access point. unicast address : The device will only connect to the given Access Point. See Basic Service Set Identifier for further details.
uint16_t	channel	Channel of the Access Point. 0 : The device will connect to a matching Access Point on any channel. 1 - 13 : The device will only connect to a matching Access Point on the given channel.
uint8_t	ie_data[]	Vendor-specific IE data added to the 802.11 Association Request frames. The IE data must be in 802.11 Vendor-Specific Element format. It may contain multiple concatenated IEs, up to the maximum length. See Vendor-Specific IE for further details.
uint16_t	ie_data_length	Length of vendor-specific Information Element (IE) data. 0 - 255 : The amount of bytes.
uint16_t	mgmt_frame_protection	Protected Management Frames (PMF) mode. WFM_MGMT_FRAME_PROTECTION_DISABLED : The device will not use PMF even if supported by the access point. WFM_MGMT_FRAME_PROTECTION_OPTIONAL : The device will use PMF if supported by the access point. WFM_MGMT_FRAME_PROTECTION_MANDATORY : The device will only connect to an access point supporting PMF. See wfm_mgmt_frame_protection for enumeration values.
uint8_t	password[64]	Password of the network. 64-bit WEP key : 5 bytes in ASCII format or 10 bytes in HEX format. 128-bit WEP key : 13 bytes in ASCII format or 26 bytes in HEX format. WPA pass phrase : 8 - 63 bytes in ASCII format. WPA PMK : 64 bytes in HEX format. See Passwords and pass phrases for further details.
uint16_t	password_length	Length of the network password. 0 - 64 : The amount of bytes.
uint8_t	prevent_roaming	Boolean option to prevent roaming between access points. 0 : The device may roam to any matching access point within the same network. 1 : The device will not roam to any other access point.
uint8_t	security_mode	Security mode of the network. WFM_SECURITY_MODE_OPEN : The device will only connect to an unsecured Access Point. WFM_SECURITY_MODE_WEP : The device will only connect to a WEP Access Point. WFM_SECURITY_MODE_WPA2_WPA1_PSK : The device will only connect to a WPA-Personal or a WPA2-Personal Access Point. WFM_SECURITY_MODE_WPA2_PSK : The device will only connect to a WPA2-Personal access point. See wfm_security_mode for enumeration values.
sl_wfx_ssid_def_t	ssid_def	Service Set Identifier (SSID) of the network.

◆ sl_wfx_connect_req_t

struct sl_wfx_connect_req_t

Request message for connecting to a Wi-Fi network.

The host can use this request to initiate a connection to a Wi-Fi network. An ongoing connection attempt can be canceled by sending sl_wfx_disconnect_req_t message. Completion of the connection request will be signaled by sl_wfx_connect_ind_t message. It may take up to 10 seconds to receive the message.

Interface mode	Request allowed
idle	Yes
station	No
AP	No
IBSS	No

Definition at line 837 of file wfm_cmd_api.h .

Data Fields
sl_wfx_connect_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_connect_cnf_body_t

struct sl_wfx_connect_cnf_body_t

Confirmation message body for sl_wfx_connect_cnf_t .

Definition at line 847 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the connection request. WFM_STATUS_SUCCESS : the connection request was accepted. It will be completed by sl_wfx_connect_ind_t . any other value : the connection request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_connect_cnf_t

struct sl_wfx_connect_cnf_t

Confirmation message for sl_wfx_connect_req_t .

Definition at line 861 of file wfm_cmd_api.h .

Data Fields
sl_wfx_connect_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_connect_ind_body_t

struct sl_wfx_connect_ind_body_t

Indication message body for sl_wfx_connect_ind_t .

Definition at line 871 of file wfm_cmd_api.h .

Data Fields
uint8_t	beacon_interval	Beacon Interval of the connected access point.
uint16_t	channel	Channel of the connected access point. 1 - 13 : Channel number.
uint8_t	dtim_period	DTIM period of the connected access point. 1 - 255 : DTIM period.
uint8_t	mac[6]	MAC address of the connected access point.
uint16_t	max_phy_rate	Maximum PHY data rate supported by the connection. See sl_wfx_rate_index_t for enumeration values.
uint32_t	status	Status of the connection request. WFM_STATUS_SUCCESS : the connection request was completed successfully. any other value : the connection request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_connect_ind_t

struct sl_wfx_connect_ind_t

Indication message used to signal the completion of a connection operation.

The device will send this indication to signal the connection request initiated with sl_wfx_connect_req_t has been completed. The indication is also sent when the device autonomously roams to another access point.

Definition at line 911 of file wfm_cmd_api.h .

Data Fields
sl_wfx_connect_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_disconnect_cnf_body_t

struct sl_wfx_disconnect_cnf_body_t

Confirmation message body for sl_wfx_disconnect_cnf_t .

Definition at line 935 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the disconnection request. WFM_STATUS_SUCCESS : the disconnection request was accepted. It will be completed by sl_wfx_disconnect_ind_t . any other value : the disconnection request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_disconnect_cnf_t

struct sl_wfx_disconnect_cnf_t

Confirmation message for sl_wfx_disconnect_req_t .

Definition at line 949 of file wfm_cmd_api.h .

Data Fields
sl_wfx_disconnect_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_disconnect_ind_body_t

struct sl_wfx_disconnect_ind_body_t

Indication message body for sl_wfx_disconnect_ind_t .

Definition at line 959 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the access point.
uint16_t	reason	Reason for disconnection. WFM_REASON_UNSPECIFIED : The device was disconnected or it disconnected on its own. See wfm_reason for enumeration values.

◆ sl_wfx_disconnect_ind_t

struct sl_wfx_disconnect_ind_t

Indication message used to signal the completion of a disconnection operation.

The device will send this indication to signal the disconnection request initiated with sl_wfx_disconnect_req_t has been completed. The indication is also sent when the device has lost the connection to an access point and has been unable to regain it.

Definition at line 979 of file wfm_cmd_api.h .

Data Fields
sl_wfx_disconnect_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_get_signal_strength_cnf_body_t

struct sl_wfx_get_signal_strength_cnf_body_t

Confirmation message body for sl_wfx_get_signal_strength_cnf_t .

Definition at line 1003 of file wfm_cmd_api.h .

Data Fields
uint32_t	rcpi	Received Channel Power Indicator (RCPI) of the connection. See Received Channel Power Indicator for further details.
uint32_t	status	Status of the get request. WFM_STATUS_SUCCESS : the get request was completed. any other value : the get request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_get_signal_strength_cnf_t

struct sl_wfx_get_signal_strength_cnf_t

Confirmation message for sl_wfx_get_signal_strength_req_t .

Definition at line 1022 of file wfm_cmd_api.h .

Data Fields
sl_wfx_get_signal_strength_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_pm_mode_req_body_t

struct sl_wfx_set_pm_mode_req_body_t

Request message body for sl_wfx_set_pm_mode_req_t .

Field	Default value	Reset to default value
power_mode	WFM_PM_MODE_ACTIVE	when interface stopped
listen_interval	0	when interface stopped

Definition at line 1038 of file wfm_cmd_api.h .

Data Fields
uint16_t	listen_interval	Number of beacons/DTIMs to skip while sleeping. 0 : wake-up on every beacon/DTIM. 1 - 600 : the number of beacon/DTIMs to skip. See Power management for further details.
uint16_t	power_mode	Power management mode. WFM_PM_MODE_ACTIVE : the device will not use Wi-Fi power management mechanisms. WFM_PM_MODE_BEACON : the device will wake-up on beacons. WFM_PM_MODE_DTIM : the device will wake-up on DTIMs. See wfm_pm_mode for enumeration values.

◆ sl_wfx_set_pm_mode_req_t

struct sl_wfx_set_pm_mode_req_t

Request message for setting the power management mode of the device.

The host can use this request to enable or disable Wi-Fi power management mechanisms.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

Definition at line 1068 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_pm_mode_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_pm_mode_cnf_body_t

struct sl_wfx_set_pm_mode_cnf_body_t

Confirmation message body for sl_wfx_set_pm_mode_cnf_t .

Definition at line 1078 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the power management request. WFM_STATUS_SUCCESS : the power management request was completed. any other value : the power management request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_pm_mode_cnf_t

struct sl_wfx_set_pm_mode_cnf_t

Confirmation message for sl_wfx_set_pm_mode_req_t .

Definition at line 1092 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_pm_mode_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_start_ap_req_body_t

struct sl_wfx_start_ap_req_body_t

Request message body for sl_wfx_start_ap_req_t .

Definition at line 1102 of file wfm_cmd_api.h .

Data Fields
uint16_t	beacon_ie_data_length	Length of vendor-specific Information Element (IE) data in 802.11 Beacon frames. 0 - 255 : The amount of bytes.
uint16_t	channel	Channel of the Access Point. 1 - 13 : The device will create the access point on the given channel.
uint8_t	client_isolation	Boolean option to isolate connected clients from each other. 0 : The device will allow connected clients to communicate with each other. 1 : The device will prevent multiple connected clients from communicating. Regardless of the value, the connected stations will always be able to communicate with the device. See Client isolation for further details.
uint8_t	hidden_ssid	Boolean option to hide the network. 0 : The device will advertise the SSID of the network to any near-by stations. 1 : The device will hide the SSID of the network and will only respond to stations that specify the SSID. See Hidden network for further details.
uint8_t	ie_data[]	Vendor-specific IE data added to the 802.11 Beacon frames and Probe Response frames. The IE data must be in 802.11 Vendor-Specific Element format. It may contain multiple concatenated IEs, up to the maximum length. First part of the IE data, up to the amount of bytes specified in BeaconIeDataLength, is added to the Beacon frames. The remaining part whose length is defined in ProbeRespIeDataLength is added to the Probe Response frames. See Vendor-Specific IE for further details.
uint8_t	mgmt_frame_protection	Protected Management Frames (PMF) mode. WFM_MGMT_FRAME_PROTECTION_DISABLED : The device will not use PMF even if supported by the connecting station. WFM_MGMT_FRAME_PROTECTION_OPTIONAL : The device will use PMF if supported by the connecting station. WFM_MGMT_FRAME_PROTECTION_MANDATORY : The device will only allow connecting stations that support PMF. See wfm_mgmt_frame_protection for enumeration values.
uint8_t	password[64]	Password of the network. 64-bit WEP key : 5 bytes in ASCII format or 10 bytes in HEX format. 128-bit WEP key : 13 bytes in ASCII format or 26 bytes in HEX format. WPA pass phrase : 8 - 63 bytes in ASCII format. WPA PMK : 64 bytes in HEX format. See Passwords and pass phrases for further details.
uint16_t	password_length	Length of the network password. 0 - 64 : The amount of bytes.
uint16_t	probe_resp_ie_data_length	Length of vendor-specific Information Element (IE) data in 802.11 Probe Response frames. 0 - 255 : The amount of bytes.
uint8_t	security_mode	Security mode of the Access Point. WFM_SECURITY_MODE_OPEN : The device will only allow unsecured connections. WFM_SECURITY_MODE_WEP : The device will only allow WEP connections. WFM_SECURITY_MODE_WPA2_WPA1_PSK : The device will only allow WPA-Personal and WPA2-Personal connections. WFM_SECURITY_MODE_WPA2_PSK : The device will only allow WPA2-Personal connections. See wfm_security_mode for enumeration values.
sl_wfx_ssid_def_t	ssid_def	Service Set Identifier (SSID) of the network.

◆ sl_wfx_start_ap_req_t

struct sl_wfx_start_ap_req_t

Request message for starting a Wi-Fi network.

The host can use this request to initiate a Wi-Fi network.

Interface mode	Request allowed
idle	Yes
station	No
AP	No
IBSS	No

Definition at line 1193 of file wfm_cmd_api.h .

Data Fields
sl_wfx_start_ap_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_start_ap_cnf_body_t

struct sl_wfx_start_ap_cnf_body_t

Confirmation message body for sl_wfx_start_ap_cnf_t .

Definition at line 1203 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the start request. WFM_STATUS_SUCCESS : the start request was accepted. It will be completed by sl_wfx_start_ap_ind_t . any other value : the start request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_start_ap_cnf_t

struct sl_wfx_start_ap_cnf_t

Confirmation message for sl_wfx_start_ap_req_t .

Definition at line 1217 of file wfm_cmd_api.h .

Data Fields
sl_wfx_start_ap_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_start_ap_ind_body_t

struct sl_wfx_start_ap_ind_body_t

Indication message body for sl_wfx_start_ap_ind_t .

Definition at line 1227 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the start request. WFM_STATUS_SUCCESS : the start request was completed successfully. any other value : the start request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_start_ap_ind_t

struct sl_wfx_start_ap_ind_t

Indication message used to signal the completion of a start request.

The device will send this indication to signal the start request initiated with sl_wfx_start_ap_req_t has been completed.

Definition at line 1243 of file wfm_cmd_api.h .

Data Fields
sl_wfx_start_ap_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_update_ap_req_body_t

struct sl_wfx_update_ap_req_body_t

Request message body for sl_wfx_update_ap_req_t .

Definition at line 1253 of file wfm_cmd_api.h .

Data Fields
uint16_t	beacon_ie_data_length	Length of vendor-specific Information Element (IE) data in 802.11 Beacon frames. 0 - 255 : The amount of bytes.
uint8_t	ie_data[]	Vendor-specific IE data added to the 802.11 Beacon frames and Probe Response frames. The IE data must be in 802.11 Vendor-Specific Element format. It may contain multiple concatenated IEs, up to the maximum length. First part of the IE data, up to the amount of bytes specified in BeaconIeDataLength, is added to the Beacon frames. The remaining part whose length is defined in ProbeRespIeDataLength is added to the Probe Response frames. See Vendor-Specific IE for further details.
uint16_t	probe_resp_ie_data_length	Length of vendor-specific Information Element (IE) data in 802.11 Probe Response frames. 0 - 255 : The amount of bytes.

◆ sl_wfx_update_ap_req_t

struct sl_wfx_update_ap_req_t

Request message for updating parameters of the started Wi-Fi network.

The host can use this request to update parameters of the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 1288 of file wfm_cmd_api.h .

Data Fields
sl_wfx_update_ap_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_update_ap_cnf_body_t

struct sl_wfx_update_ap_cnf_body_t

Confirmation message body for sl_wfx_update_ap_cnf_t .

Definition at line 1298 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the update request. WFM_STATUS_SUCCESS : the update request was completed. any other value : the update request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_update_ap_cnf_t

struct sl_wfx_update_ap_cnf_t

Confirmation message for sl_wfx_update_ap_req_t .

Definition at line 1312 of file wfm_cmd_api.h .

Data Fields
sl_wfx_update_ap_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_stop_ap_cnf_body_t

struct sl_wfx_stop_ap_cnf_body_t

Confirmation message body for sl_wfx_stop_ap_cnf_t .

Definition at line 1336 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the stop request. WFM_STATUS_SUCCESS : the stop request was accepted. It will be completed by sl_wfx_stop_ap_ind_t . any other value : the stop request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_stop_ap_cnf_t

struct sl_wfx_stop_ap_cnf_t

Confirmation message for sl_wfx_stop_ap_req_t .

Definition at line 1350 of file wfm_cmd_api.h .

Data Fields
sl_wfx_stop_ap_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_ap_client_connected_ind_body_t

struct sl_wfx_ap_client_connected_ind_body_t

Indication message body for sl_wfx_ap_client_connected_ind_t .

Definition at line 1370 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the station.

◆ sl_wfx_ap_client_connected_ind_t

struct sl_wfx_ap_client_connected_ind_t

Indication message used to signal a connected station.

The device will send this indication to signal a station has connected to the started network.

Definition at line 1383 of file wfm_cmd_api.h .

Data Fields
sl_wfx_ap_client_connected_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_ap_client_rejected_ind_body_t

struct sl_wfx_ap_client_rejected_ind_body_t

Indication message body for sl_wfx_ap_client_rejected_ind_t .

Definition at line 1393 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the station.
uint16_t	reason	Reason for rejection. WFM_REASON_TIMEOUT : A timeout occurred during a station connection attempt. WFM_REASON_LEAVING_BSS : The device sent a deauth before completing the connection. WFM_REASON_UNKNOWN_STA : The device received data from a non-connected station. WFM_REASON_AP_FULL : The device was not able to accommodate any more stations. WFM_REASON_AUTHENTICATION_FAILURE : The device did not complete the WPA authentication successfully. See wfm_reason for enumeration values.

◆ sl_wfx_ap_client_rejected_ind_t

struct sl_wfx_ap_client_rejected_ind_t

Indication message used to signal a rejected connection attempt from a station.

The device will send this indication to signal a station has attempted connection to the started network and was rejected by the device.

Definition at line 1416 of file wfm_cmd_api.h .

Data Fields
sl_wfx_ap_client_rejected_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_disconnect_ap_client_req_body_t

struct sl_wfx_disconnect_ap_client_req_body_t

Request message body for sl_wfx_disconnect_ap_client_req_t .

Definition at line 1426 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the station.

◆ sl_wfx_disconnect_ap_client_req_t

struct sl_wfx_disconnect_ap_client_req_t

Request message for disconnecting a client from the started Wi-Fi network.

The host can use this request to disconnect a client from the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 1445 of file wfm_cmd_api.h .

Data Fields
sl_wfx_disconnect_ap_client_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_disconnect_ap_client_cnf_body_t

struct sl_wfx_disconnect_ap_client_cnf_body_t

Confirmation message body for sl_wfx_disconnect_ap_client_cnf_t .

Definition at line 1455 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the disconnect request. WFM_STATUS_SUCCESS : the disconnect request was completed. any other value : the disconnect request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_disconnect_ap_client_cnf_t

struct sl_wfx_disconnect_ap_client_cnf_t

Confirmation message for sl_wfx_disconnect_ap_client_req_t .

Definition at line 1469 of file wfm_cmd_api.h .

Data Fields
sl_wfx_disconnect_ap_client_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_ap_client_disconnected_ind_body_t

struct sl_wfx_ap_client_disconnected_ind_body_t

Indication message body for sl_wfx_ap_client_disconnected_ind_t .

Definition at line 1479 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the station.
uint16_t	reason	Reason for disconnection. WFM_REASON_LEAVING_BSS : The station was disconnected or it disconnected on its own. See wfm_reason for enumeration values.

◆ sl_wfx_ap_client_disconnected_ind_t

struct sl_wfx_ap_client_disconnected_ind_t

Indication message used to signal a disconnected station.

The device will send this indication to signal a station has left the started network.

Definition at line 1498 of file wfm_cmd_api.h .

Data Fields
sl_wfx_ap_client_disconnected_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_send_frame_req_body_t

struct sl_wfx_send_frame_req_body_t

Request message body for sl_wfx_send_frame_req_t .

Definition at line 1508 of file wfm_cmd_api.h .

Data Fields
uint8_t	frame_type	Packet type. 0 : Data packet with Ethernet II frame header.
uint8_t	packet_data[]	Data of the packet. See Packet types for further details.
uint32_t	packet_data_length	Length of packet data. 1 - 1604 : The amount of bytes.
uint16_t	packet_id	Packet ID number. 0 - 65535 : Host-assigned unique number for the packet. The number is returned in the corresponding confirmation message.
uint8_t	priority	User Priority level. 0 - 7 : 802.1D Priority field value.

◆ sl_wfx_send_frame_req_t

struct sl_wfx_send_frame_req_t

Request message for sending a packet to the network.

The host can use this request to send a packet to the network.

Interface mode	Request allowed
idle	No
station	Yes
AP	Yes
IBSS	Yes

Definition at line 1551 of file wfm_cmd_api.h .

Data Fields
sl_wfx_send_frame_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_send_frame_cnf_body_t

struct sl_wfx_send_frame_cnf_body_t

Confirmation message body for sl_wfx_send_frame_cnf_t .

Definition at line 1561 of file wfm_cmd_api.h .

Data Fields
uint16_t	packet_id	Packet ID number from the corresponding request.
uint16_t	reserved	Reserved.
uint32_t	status	Status of the send request. WFM_STATUS_SUCCESS : the send request was completed. any other value : the send request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_send_frame_cnf_t

struct sl_wfx_send_frame_cnf_t

Confirmation message for sl_wfx_send_frame_req_t .

Definition at line 1585 of file wfm_cmd_api.h .

Data Fields
sl_wfx_send_frame_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_received_ind_body_t

struct sl_wfx_received_ind_body_t

Indication message body for sl_wfx_received_ind_t .

Definition at line 1595 of file wfm_cmd_api.h .

Data Fields
uint8_t	frame[]	Packet data, including the padding bytes before the packet data. See Packet types for further details.
uint16_t	frame_length	Length of packet data excluding the padding bytes. 1 - 2310 : The amount of bytes.
uint8_t	frame_padding	The amount of padding bytes before the packet data. 0 - 3 : The amount of bytes.
uint8_t	frame_type	Packet type. 0 : Data packet with Ethernet II frame header.

◆ sl_wfx_received_ind_t

struct sl_wfx_received_ind_t

Indication message used to signal a received packet.

The device will send this indication to signal a packet has been received.

Definition at line 1626 of file wfm_cmd_api.h .

Data Fields
sl_wfx_received_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_start_scan_req_body_t

struct sl_wfx_start_scan_req_body_t

Request message body for sl_wfx_start_scan_req_t .

Definition at line 1636 of file wfm_cmd_api.h .

Data Fields
uint16_t	channel_list_count	The amount of specific channels to scan. 0 : The device will scan all channels 1 - 13 : The amount of specific channels to scan.
uint8_t	data[]	Data for the variable-length scan parameters. The variable-length scan parameters are concatenated together without any padding between the different parameters. 1. List of specific channels to scan. 1 - 13 : The channel number to scan per byte. Must contain the same number of channels as specified in ChannelListCount. See Scanning for further details. 2. List of specific SSIDs to scan. Must contain the same number of WfmHiSsidDef_t elements as specified in SsidListCount. This parameter is applicable only for an active scan. See Scanning for further details. 3. Vendor-specific IE data added to the 802.11 Probe Request frames. The IE data must be in 802.11 Vendor-Specific Element format. It may contain multiple concatenated IEs, up to the maximum length. This parameter is applicable only for an active scan. See Vendor-Specific IE for further details. 4. Basic Service Set Identifier (BSSID) to scan. broadcast address : The device will send Probe Request frames to all devices. unicast address : The device will send Probe Request frames to a specific device. This parameter is applicable only for an active scan. If not specified, broadcast address is assumed. Note that an SSID list must be specified when using the unicast address, otherwise the received scan results may contain unexpected additional networks. See Basic Service Set Identifier for further details.
uint16_t	ie_data_length	Length of vendor-specific Information Element (IE) data in 802.11 Probe Request frames. 0 - 255 : The amount of bytes.
uint16_t	scan_mode	Scan mode. WFM_SCAN_MODE_PASSIVE : The device will perform a passive scan. WFM_SCAN_MODE_ACTIVE : The device will perform an active scan. See wfm_scan_mode for enumeration values. See Scanning for further details.
uint16_t	ssid_list_count	The amount of specific SSIDs to scan. 0 : The device will perform a broadcast scan 1 - 2 : The amount of specific SSIDs to scan.

◆ sl_wfx_start_scan_req_t

struct sl_wfx_start_scan_req_t

Request message for starting a scan to detect near-by access points.

The host can use this request to start a scan operation to detect near-by access points.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	No
IBSS	No

Definition at line 1701 of file wfm_cmd_api.h .

Data Fields
sl_wfx_start_scan_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_start_scan_cnf_body_t

struct sl_wfx_start_scan_cnf_body_t

Confirmation message body for sl_wfx_start_scan_cnf_t .

Definition at line 1711 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the scan request. WFM_STATUS_SUCCESS : the scan request was accepted. It will be completed by sl_wfx_scan_complete_ind_t . any other value : the scan request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_start_scan_cnf_t

struct sl_wfx_start_scan_cnf_t

Confirmation message for sl_wfx_start_scan_req_t .

Definition at line 1726 of file wfm_cmd_api.h .

Data Fields
sl_wfx_start_scan_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_stop_scan_cnf_body_t

struct sl_wfx_stop_scan_cnf_body_t

Confirmation message body for sl_wfx_stop_scan_cnf_t .

Definition at line 1751 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the stop request. WFM_STATUS_SUCCESS : the stop request was accepted. It will be completed by WFM_HI_SCAN_COMPLETE_IND. any other value : the stop request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_stop_scan_cnf_t

struct sl_wfx_stop_scan_cnf_t

Confirmation message for sl_wfx_stop_scan_req_t .

Definition at line 1766 of file wfm_cmd_api.h .

Data Fields
sl_wfx_stop_scan_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_scan_result_ind_body_t

struct sl_wfx_scan_result_ind_body_t

Indication message body for sl_wfx_scan_result_ind_t .

Definition at line 1776 of file wfm_cmd_api.h .

Data Fields
uint16_t	channel	Channel of the access point. 1 - 13 : Channel number.
uint8_t	ie_data[]	Access point IE data from the 802.11 Beacon or Probe Response frame.
uint16_t	ie_data_length	Length of access point Information Element (IE) data in bytes.
uint8_t	mac[6]	MAC address of the access point.
uint16_t	rcpi	Received Channel Power Indicator (RCPI) of the access point. See Received Channel Power Indicator for further details.
uint8_t	reserved1	Reserved.
uint16_t	reserved2	Reserved.
sl_wfx_security_mode_bitmask_t	security_mode	Security Capabilities of the network.
sl_wfx_ssid_def_t	ssid_def	Service Set Identifier (SSID) of the network.

◆ sl_wfx_scan_result_ind_t

struct sl_wfx_scan_result_ind_t

Indication message used to signal an access point has been detected.

The device will send this indication to signal an access point has has been detected during the scan operation.

Definition at line 1824 of file wfm_cmd_api.h .

Data Fields
sl_wfx_scan_result_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_scan_complete_ind_body_t

struct sl_wfx_scan_complete_ind_body_t

Indication message body for sl_wfx_scan_complete_ind_t .

Definition at line 1834 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the scan request. WFM_STATUS_SUCCESS : the scan request was completed. any other value : the scan request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_scan_complete_ind_t

struct sl_wfx_scan_complete_ind_t

Indication message used to signal a scan was completed.

The device will send this indication to signal a scan operation has been completed.

Definition at line 1851 of file wfm_cmd_api.h .

Data Fields
sl_wfx_scan_complete_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_join_ibss_req_body_t

struct sl_wfx_join_ibss_req_body_t

Request message body for sl_wfx_join_ibss_req_t .

Definition at line 1861 of file wfm_cmd_api.h .

Data Fields
uint32_t	channel	Channel of the network. 0 : The device will connect to a matching network on any channel. 1 - 13 : The device will only connect to a matching network on the given channel.
uint8_t	password[64]	Password of the network. 64-bit WEP key : 5 bytes in ASCII format or 10 bytes in HEX format. 128-bit WEP key : 13 bytes in ASCII format or 26 bytes in HEX format. See Passwords and pass phrases for further details.
uint16_t	password_length	Length of the network password. 0 - 26 : The amount of bytes.
uint16_t	security_mode	Security mode of the network. WFM_SECURITY_MODE_OPEN : The device will only use unsecured connections. WFM_SECURITY_MODE_WEP : The device will only use WEP connections. See wfm_security_mode for enumeration values.
sl_wfx_ssid_def_t	ssid_def	Service Set Identifier (SSID) of the network.

◆ sl_wfx_join_ibss_req_t

struct sl_wfx_join_ibss_req_t

Request message for connecting to or starting an IBSS network.

The host can use this request to connect to an IBSS network. If no existing network is found, the device will start a new network.

Interface mode	Request allowed
idle	Yes
station	No
AP	No
IBSS	No

Definition at line 1906 of file wfm_cmd_api.h .

Data Fields
sl_wfx_join_ibss_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_join_ibss_cnf_body_t

struct sl_wfx_join_ibss_cnf_body_t

Confirmation message body for sl_wfx_join_ibss_cnf_t .

Definition at line 1916 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the join request. WFM_STATUS_SUCCESS : the join request was accepted. It will be completed by sl_wfx_join_ibss_ind_t . any other value : the join request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_join_ibss_cnf_t

struct sl_wfx_join_ibss_cnf_t

Confirmation message for sl_wfx_join_ibss_req_t .

Definition at line 1930 of file wfm_cmd_api.h .

Data Fields
sl_wfx_join_ibss_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_join_ibss_ind_body_t

struct sl_wfx_join_ibss_ind_body_t

Indication message body for sl_wfx_join_ibss_ind_t .

Definition at line 1940 of file wfm_cmd_api.h .

Data Fields
uint8_t	bssid[6]	Basic Service Set Identifier (BSSID) of the network. See Basic Service Set Identifier for further details.
uint16_t	reserved	Reserved.
uint32_t	status	Status of the join request. WFM_STATUS_SUCCESS : the join request was completed successfully. any other value : the join request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_join_ibss_ind_t

struct sl_wfx_join_ibss_ind_t

Indication message used to signal the completion of a join request.

The device will send this indication to signal the join request initiated with sl_wfx_join_ibss_req_t has been completed.

Definition at line 1965 of file wfm_cmd_api.h .

Data Fields
sl_wfx_join_ibss_ind_body_t	body	Indication message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_leave_ibss_cnf_body_t

struct sl_wfx_leave_ibss_cnf_body_t

Confirmation message body for sl_wfx_leave_ibss_cnf_t .

Definition at line 1989 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the disconnect request. WFM_STATUS_SUCCESS : the disconnect request was accepted. It will be completed by sl_wfx_leave_ibss_ind_t . any other value : the disconnect request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_leave_ibss_cnf_t

struct sl_wfx_leave_ibss_cnf_t

Confirmation message for sl_wfx_leave_ibss_req_t .

Definition at line 2003 of file wfm_cmd_api.h .

Data Fields
sl_wfx_leave_ibss_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_multicast_addr_req_body_t

struct sl_wfx_add_multicast_addr_req_body_t

Request message body for sl_wfx_add_multicast_addr_req_t .

Definition at line 2023 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address to add. broadcast address : The device will empty the whitelist and allow all multicast addresses. zero address : The device will empty the whitelist and deny all multicast addresses. multicast address : The device will add the given address to the whitelist. See Basic Service Set Identifier for further details.

◆ sl_wfx_add_multicast_addr_req_t

struct sl_wfx_add_multicast_addr_req_t

Request message for adding a multicast address to the multicast filter whitelist.

The host can use this request to add a multicast address to the multicast filter whitelist. When the first address is added the whitelist, the device will discard all multicast frames whose destination address does not match any of the addresses on the list. The default state is to allow all multicast addresses. The whitelist is reset to the default state when the interface is reset. Up to 8 multicast addresses may be added.
See Filtering for further details.

Interface mode	Request allowed
idle	No
station	Yes
AP	Yes
IBSS	No

Definition at line 2053 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_multicast_addr_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_multicast_addr_cnf_body_t

struct sl_wfx_add_multicast_addr_cnf_body_t

Confirmation message body for sl_wfx_add_multicast_addr_cnf_t .

Definition at line 2063 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the add request was completed successfully. any other value : the add request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_add_multicast_addr_cnf_t

struct sl_wfx_add_multicast_addr_cnf_t

Confirmation message for sl_wfx_add_multicast_addr_req_t .

Definition at line 2078 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_multicast_addr_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_remove_multicast_addr_req_body_t

struct sl_wfx_remove_multicast_addr_req_body_t

Request message body for sl_wfx_remove_multicast_addr_req_t .

Definition at line 2088 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address to remove. multicast address : The device will remove the given address from the whitelist. See Basic Service Set Identifier for further details.

◆ sl_wfx_remove_multicast_addr_req_t

struct sl_wfx_remove_multicast_addr_req_t

Request message for removing a multicast address from the multicast filter whitelist.

The host can use this request to remove a multicast address from the multicast filter whitelist.

Interface mode	Request allowed
idle	No
station	Yes
AP	Yes
IBSS	No

Definition at line 2111 of file wfm_cmd_api.h .

Data Fields
sl_wfx_remove_multicast_addr_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_remove_multicast_addr_cnf_body_t

struct sl_wfx_remove_multicast_addr_cnf_body_t

Confirmation message body for sl_wfx_remove_multicast_addr_cnf_t .

Definition at line 2121 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the remove request. WFM_STATUS_SUCCESS : the remove request was completed successfully. any other value : the remove request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_remove_multicast_addr_cnf_t

struct sl_wfx_remove_multicast_addr_cnf_t

Confirmation message for sl_wfx_remove_multicast_addr_req_t .

Definition at line 2136 of file wfm_cmd_api.h .

Data Fields
sl_wfx_remove_multicast_addr_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_ap_client_count_req_body_t

struct sl_wfx_set_max_ap_client_count_req_body_t

Request message body for sl_wfx_set_max_ap_client_count_req_t .

Field	Default value	Reset to default value
Count	8	when interface stopped

Definition at line 2151 of file wfm_cmd_api.h .

Data Fields
uint32_t	count	Maximum number of connected clients. 0 : The device will set the limit value to the device default. 1 - 8 : The maximum number of connected clients.

◆ sl_wfx_set_max_ap_client_count_req_t

struct sl_wfx_set_max_ap_client_count_req_t

Request message for setting the maximum number of connected clients.

The host can use this request to limit the number of stations that can connect the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 2173 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_ap_client_count_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_ap_client_count_cnf_body_t

struct sl_wfx_set_max_ap_client_count_cnf_body_t

Confirmation message body for sl_wfx_set_max_ap_client_count_cnf_t .

Definition at line 2183 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_max_ap_client_count_cnf_t

struct sl_wfx_set_max_ap_client_count_cnf_t

Confirmation message for sl_wfx_set_max_ap_client_count_req_t .

Definition at line 2197 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_ap_client_count_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_ap_client_inactivity_req_body_t

struct sl_wfx_set_max_ap_client_inactivity_req_body_t

Request message body for sl_wfx_set_max_ap_client_inactivity_req_t .

Field	Default value	Reset to default value
inactivity_timeout	65	when interface stopped

Definition at line 2212 of file wfm_cmd_api.h .

Data Fields
uint32_t	inactivity_timeout	Maximum amount of client idle time. 0 : The device will set the limit value to the device default. 1 - 240 : The maximum number of seconds.

◆ sl_wfx_set_max_ap_client_inactivity_req_t

struct sl_wfx_set_max_ap_client_inactivity_req_t

Request message for setting the maximum number of connected clients.

The host can use this request to limit the number of stations that can connect the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 2234 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_ap_client_inactivity_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_ap_client_inactivity_cnf_body_t

struct sl_wfx_set_max_ap_client_inactivity_cnf_body_t

Confirmation message body for sl_wfx_set_max_ap_client_count_cnf_t .

Definition at line 2244 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_max_ap_client_inactivity_cnf_t

struct sl_wfx_set_max_ap_client_inactivity_cnf_t

Confirmation message for sl_wfx_set_max_ap_client_inactivity_req_t .

Definition at line 2258 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_ap_client_inactivity_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_roam_parameters_req_body_t

struct sl_wfx_set_roam_parameters_req_body_t

Request message body for sl_wfx_set_roam_parameters_req_t .

Field	Default value	Reset to default value
rcpi_threshold	60	when device reset
rcpi_hysteresis	120	when device reset
beacon_lost_count	10	when device reset
channel_list_count	13	when device reset
channel_number	1 to 13	when device reset

Definition at line 2277 of file wfm_cmd_api.h .

Data Fields
uint8_t	beacon_lost_count	Beacon loss limit for a roaming attempt. 0 : The device will set the limit value to the device default. 1 - 255 : Beacon loss limit for a roaming attempt.
uint8_t	channel_list_count	The amount of specific channels to scan. 0 : The device will set the channel list to the device default. 1 - 13 : The amount of specific channels to scan.
uint8_t	channel_number[]	List of specific channels to scan. 1 - 13 : The channel number to scan per byte. Must contain the same number of channels as specified in channel_list_count. See Scanning for further details.
uint8_t	rcpi_hysteresis	Upper RCPI limit that must be attained before triggering roaming again. 0 : The device will set the limit value to the device default. 1 - 220 : RCPI limit to re-enable automatic roaming based on RCPI. This value is used to prevent automatic roaming from triggering again and again while the signal strength stays close to the rcpi_threshold value. rcpi_hysteresis should be set to a value grater than rcpi_threshold. See Received Channel Power Indicator for further details.
uint8_t	rcpi_threshold	Received Channel Power Indicator (RCPI) limit for a roaming attempt. 0 : The device will set the limit value to the device default. 1 - 220 : RCPI limit for a roaming attempt. See Received Channel Power Indicator for further details.

◆ sl_wfx_set_roam_parameters_req_t

struct sl_wfx_set_roam_parameters_req_t

Request message for setting the roaming parameters.

The host can use this request to configure the roaming parameters used by the device.
See Roaming for further details.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	No
IBSS	No

Definition at line 2331 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_roam_parameters_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_roam_parameters_cnf_body_t

struct sl_wfx_set_roam_parameters_cnf_body_t

Confirmation message body for sl_wfx_set_roam_parameters_cnf_t .

Definition at line 2341 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_roam_parameters_cnf_t

struct sl_wfx_set_roam_parameters_cnf_t

Confirmation message for sl_wfx_set_roam_parameters_req_t .

Definition at line 2356 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_roam_parameters_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_tx_rate_parameters_req_body_t

struct sl_wfx_set_tx_rate_parameters_req_body_t

Request message body for sl_wfx_set_tx_rate_parameters_req_t .

Field	Default value	Reset to default value
rate_set_bitmask	all 802.11bg rates, MCS 0 - 7	when device reset

Definition at line 2371 of file wfm_cmd_api.h .

Data Fields
sl_wfx_rate_set_bitmask_t	rate_set_bitmask	TX rate set parameters.
uint32_t	reserved	Reserved, set to zero.

◆ sl_wfx_set_tx_rate_parameters_req_t

struct sl_wfx_set_tx_rate_parameters_req_t

Request message for setting the TX rate set parameters.

The host can use this request to configure the TX rate set parameters of the device. The rate set determines what data rates will be used by the device to transmit data frames.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	No
IBSS	No

Definition at line 2398 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_tx_rate_parameters_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_tx_rate_parameters_cnf_body_t

struct sl_wfx_set_tx_rate_parameters_cnf_body_t

Confirmation message body for sl_wfx_set_tx_rate_parameters_cnf_t .

Definition at line 2408 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_tx_rate_parameters_cnf_t

struct sl_wfx_set_tx_rate_parameters_cnf_t

Confirmation message for sl_wfx_set_tx_rate_parameters_req_t .

Definition at line 2423 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_tx_rate_parameters_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_arp_ip_address_req_body_t

struct sl_wfx_set_arp_ip_address_req_body_t

Request message body for sl_wfx_set_arp_ip_address_req_t .

Definition at line 2433 of file wfm_cmd_api.h .

Data Fields
uint32_t	arp_ip_addr[2]	List of offloaded ARP IP addresses. The device will automatically reply to an ARP request that matches one the addresses on the list. Note that addresses not in use must be set to zero. Offloading is disabled by setting all addresses to zero. See Offloading for further details.

◆ sl_wfx_set_arp_ip_address_req_t

struct sl_wfx_set_arp_ip_address_req_t

Request message for setting the Address Resolution Protocol (ARP) offloading state.

The host can use this request to offload handling of ARP requests to the device. When offloading is enabled, the device will automatically respond to ARP requests with an ARP reply. By default offloading is disabled. Offloading is reset to the default state when the interface is reset.
See Offloading for further details.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

Definition at line 2461 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_arp_ip_address_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_arp_ip_address_cnf_body_t

struct sl_wfx_set_arp_ip_address_cnf_body_t

Confirmation message body for sl_wfx_set_arp_ip_address_cnf_t .

Definition at line 2471 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_arp_ip_address_cnf_t

struct sl_wfx_set_arp_ip_address_cnf_t

Confirmation message for sl_wfx_set_arp_ip_address_req_t .

Definition at line 2485 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_arp_ip_address_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_ns_ip_address_req_body_t

struct sl_wfx_set_ns_ip_address_req_body_t

Request message body for sl_wfx_set_ns_ip_address_req_t .

Definition at line 2495 of file wfm_cmd_api.h .

Data Fields
sl_wfx_ns_ip_addr_t	ns_ip_addr[2]	List of offloaded NS IP addresses. The device will automatically reply to a NS that matches one the addresses on the list. Note that addresses not in use must be set to zero. Offloading is disabled by setting all addresses to zero. See Offloading for further details.

◆ sl_wfx_set_ns_ip_address_req_t

struct sl_wfx_set_ns_ip_address_req_t

Request message for setting the Neighbor Discovery Protocol (NDP) offloading state.

The host can use this request to offload handling of IPv6 Neighbor Solicitations to the device. When offloading is enabled, the device will automatically respond to a solicitation with a Neighbor Advertisement. By default offloading is disabled. Offloading is reset to the default state when the interface is reset.
See Offloading for further details.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

Definition at line 2522 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_ns_ip_address_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_ns_ip_address_cnf_body_t

struct sl_wfx_set_ns_ip_address_cnf_body_t

Confirmation message body for sl_wfx_set_ns_ip_address_cnf_t .

Definition at line 2532 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_ns_ip_address_cnf_t

struct sl_wfx_set_ns_ip_address_cnf_t

Confirmation message for sl_wfx_set_ns_ip_address_req_t .

Definition at line 2546 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_ns_ip_address_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_broadcast_filter_req_body_t

struct sl_wfx_set_broadcast_filter_req_body_t

Request message body for sl_wfx_set_broadcast_filter_req_t .

Field	Default value	Reset to default value
Filter	0	when interface stopped

Definition at line 2561 of file wfm_cmd_api.h .

Data Fields
uint32_t	filter	Boolean option for broadcast filtering. 0 : The device will forward all received broadcast frames to the host. 1 : The device will only forward ARP and DHCP frames to the host, other broadcast frames are discarded. See Filtering for further details.

◆ sl_wfx_set_broadcast_filter_req_t

struct sl_wfx_set_broadcast_filter_req_t

Request message for setting broadcast filter state.

The host can use this request to configure the state of the broadcast filter. When enabled, the device will only forward certain broadcast frames to the host and automatically discard the rest.
See Filtering for further details.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

Definition at line 2587 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_broadcast_filter_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_broadcast_filter_cnf_body_t

struct sl_wfx_set_broadcast_filter_cnf_body_t

Confirmation message body for sl_wfx_set_broadcast_filter_cnf_t .

Definition at line 2597 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_broadcast_filter_cnf_t

struct sl_wfx_set_broadcast_filter_cnf_t

Confirmation message for sl_wfx_set_broadcast_filter_req_t .

Definition at line 2611 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_broadcast_filter_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_scan_parameters_req_body_t

struct sl_wfx_set_scan_parameters_req_body_t

Request message body for sl_wfx_set_scan_parameters_req_t .

Field	Default value	Reset to default value
active_channel_time	50	when device reset
passive_channel_time	110	when device reset
num_of_probe_requests	1	when device reset

Definition at line 2628 of file wfm_cmd_api.h .

Data Fields
uint16_t	active_channel_time	Set to 0 for device default, 1 - 550 TUs.
uint16_t	num_of_probe_requests	Set to 0 for device default, 1 - 2.
uint16_t	passive_channel_time	Set to 0 for device default, 1 - 550 TUs.
uint16_t	reserved	Reserved, set to zero.

◆ sl_wfx_set_scan_parameters_req_t

struct sl_wfx_set_scan_parameters_req_t

Request message for setting scan parameters.

The host can use this request to configure the scan parameters used by the device.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	No
IBSS	No

Definition at line 2661 of file wfm_cmd_api.h .

◆ sl_wfx_set_scan_parameters_cnf_body_t

struct sl_wfx_set_scan_parameters_cnf_body_t

Confirmation message body for sl_wfx_set_scan_parameters_cnf_t .

Definition at line 2669 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_scan_parameters_cnf_t

struct sl_wfx_set_scan_parameters_cnf_t

Confirmation message for sl_wfx_set_scan_parameters_req_t .

Definition at line 2683 of file wfm_cmd_api.h .

◆ sl_wfx_set_unicast_filter_req_body_t

struct sl_wfx_set_unicast_filter_req_body_t

Request message body for sl_wfx_set_unicast_filter_req_t .

Field	Default value	Reset to default value
Filter	1	when interface stopped

Definition at line 2696 of file wfm_cmd_api.h .

Data Fields
uint32_t	filter	Boolean option for unicast filtering. 0 : The device will forward all received unicast frames to the host. 1 : The device will only forward unicast frames whose destination address matches the device MAC address. See Filtering for further details.

◆ sl_wfx_set_unicast_filter_req_t

struct sl_wfx_set_unicast_filter_req_t

Request message for setting unicast filter state.

The host can use this request to configure the state of the unicast filter. When enabled, the device will only forward certain unicast frames to the host and automatically discard the rest.
See Filtering for further details.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 2722 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_unicast_filter_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_unicast_filter_cnf_body_t

struct sl_wfx_set_unicast_filter_cnf_body_t

Confirmation message body for sl_wfx_set_unicast_filter_cnf_t .

Definition at line 2732 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the set request. WFM_STATUS_SUCCESS : the set request was completed successfully. any other value : the set request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_unicast_filter_cnf_t

struct sl_wfx_set_unicast_filter_cnf_t

Confirmation message for sl_wfx_set_unicast_filter_req_t .

Definition at line 2746 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_unicast_filter_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_whitelist_addr_req_body_t

struct sl_wfx_add_whitelist_addr_req_body_t

Request message body for sl_wfx_add_whitelist_addr_req_t .

Definition at line 2756 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address to add. broadcast address : The device will allow all MAC addresses. unicast address : The device will add the given address to the whitelist.

◆ sl_wfx_add_whitelist_addr_req_t

struct sl_wfx_add_whitelist_addr_req_t

Request message for adding a MAC address to the device whitelist.

The host can use this request to add a MAC address to the list of allowed MAC addresses. When the first address is added the whitelist, the device will prevent communication with any devices whose MAC address does not match any of the addresses on the list. Setting a whitelist will clear all entries from the device blacklist. The default state is to allow all MAC addresses. The whitelist is reset to the default state when the interface is reset. Up to 8 MAC addresses may be added.
See Filtering for further details.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 2783 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_whitelist_addr_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_whitelist_addr_cnf_body_t

struct sl_wfx_add_whitelist_addr_cnf_body_t

Confirmation message body for sl_wfx_add_whitelist_addr_cnf_t .

Definition at line 2793 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the add request was completed successfully. any other value : the add request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_add_whitelist_addr_cnf_t

struct sl_wfx_add_whitelist_addr_cnf_t

Confirmation message for sl_wfx_add_whitelist_addr_req_t .

Definition at line 2807 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_whitelist_addr_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_blacklist_addr_req_body_t

struct sl_wfx_add_blacklist_addr_req_body_t

Request message body for sl_wfx_add_blacklist_addr_req_t .

Definition at line 2817 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address to add. broadcast address : The device will deny all MAC addresses. unicast address : The device will add the given address to the blacklist.

◆ sl_wfx_add_blacklist_addr_req_t

struct sl_wfx_add_blacklist_addr_req_t

Request message for adding a MAC address to the device blacklist.

The host can use this request to add a MAC address to the list of denied MAC addresses. When the first address is added the blacklist, the device will prevent communication with any device whose MAC address matches any of the addresses on the list. Setting a blacklist will clear all entries from the device whitelist. The default state is to allow all MAC addresses. The blacklist is reset to the default state when the interface is reset. Up to 8 MAC addresses may be added.
See Filtering for further details.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 2844 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_blacklist_addr_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_add_blacklist_addr_cnf_body_t

struct sl_wfx_add_blacklist_addr_cnf_body_t

Confirmation message body for sl_wfx_add_blacklist_addr_cnf_t .

Definition at line 2854 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the add request was completed successfully. any other value : the add request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_add_blacklist_addr_cnf_t

struct sl_wfx_add_blacklist_addr_cnf_t

Confirmation message for sl_wfx_add_blacklist_addr_req_t .

Definition at line 2868 of file wfm_cmd_api.h .

Data Fields
sl_wfx_add_blacklist_addr_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_tx_power_req_body_t

struct sl_wfx_set_max_tx_power_req_body_t

Request message body for sl_wfx_set_max_tx_power_req_t .

Field	Default value	Reset to default value
max_tx_power	device dependent	when device reset

Definition at line 2883 of file wfm_cmd_api.h .

Data Fields
int32_t	max_tx_power	Maximum transmit power to set. Expressed in units of 0.1d_bm.

◆ sl_wfx_set_max_tx_power_req_t

struct sl_wfx_set_max_tx_power_req_t

Request message for setting the maximum transmit power of the device.

The host can use this request to set a maximum transmit power. The device can still use a lower transmit power depending on regulatory rules or internal limitations.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	Yes
IBSS	Yes

Definition at line 2908 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_tx_power_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_set_max_tx_power_cnf_body_t

struct sl_wfx_set_max_tx_power_cnf_body_t

Confirmation message body for sl_wfx_set_max_tx_power_cnf_t .

Definition at line 2918 of file wfm_cmd_api.h .

Data Fields
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the add request was completed successfully. any other value : the add request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_set_max_tx_power_cnf_t

struct sl_wfx_set_max_tx_power_cnf_t

Confirmation message for sl_wfx_set_max_tx_power_req_t .

Definition at line 2935 of file wfm_cmd_api.h .

Data Fields
sl_wfx_set_max_tx_power_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_get_max_tx_power_cnf_body_t

struct sl_wfx_get_max_tx_power_cnf_body_t

Confirmation message body for sl_wfx_get_max_tx_power_cnf_t .

Definition at line 2962 of file wfm_cmd_api.h .

Data Fields
int32_t	max_tx_power_rf_port1	Maximum transmit power for RF port 1. Expressed in units of 0.1d_bm.
int32_t	max_tx_power_rf_port2	Maximum transmit power for RF port 2. Expressed in units of 0.1d_bm.
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the add request was completed successfully. any other value : the add request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_get_max_tx_power_cnf_t

struct sl_wfx_get_max_tx_power_cnf_t

Confirmation message for sl_wfx_get_max_tx_power_req_t .

Definition at line 2989 of file wfm_cmd_api.h .

Data Fields
sl_wfx_get_max_tx_power_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_get_pmk_cnf_body_t

struct sl_wfx_get_pmk_cnf_body_t

Confirmation message body for sl_wfx_get_pmk_cnf_t .

Definition at line 3017 of file wfm_cmd_api.h .

Data Fields
uint8_t	password[64]	PMK of the network. WPA PMK : 64 bytes in HEX format. See Passwords and pass phrases for further details.
uint32_t	password_length	Length of the Pairwise Master Key. 0 - 64 : The amount of bytes.
uint32_t	status	Status of the add request. WFM_STATUS_SUCCESS : the get request was completed successfully. any other value : the get request failed. See sl_wfx_fmac_status_t for enumeration values.

◆ sl_wfx_get_pmk_cnf_t

struct sl_wfx_get_pmk_cnf_t

Confirmation message for sl_wfx_get_pmk_req_t .

Definition at line 3043 of file wfm_cmd_api.h .

Data Fields
sl_wfx_get_pmk_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_get_ap_client_signal_strength_req_body_t

struct sl_wfx_get_ap_client_signal_strength_req_body_t

Request message body for sl_wfx_get_ap_client_signal_strength_req_t .

Definition at line 3053 of file wfm_cmd_api.h .

Data Fields
uint8_t	mac[6]	MAC address of the station.

◆ sl_wfx_get_ap_client_signal_strength_req_t

struct sl_wfx_get_ap_client_signal_strength_req_t

Request message for retrieving the signal strength of a client of the started Wi-Fi network.

The host can use this request to retrieve the signal strength of a client of the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

Definition at line 3072 of file wfm_cmd_api.h .

Data Fields
sl_wfx_get_ap_client_signal_strength_req_body_t	body	Request message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_get_ap_client_signal_strength_cnf_body_t

struct sl_wfx_get_ap_client_signal_strength_cnf_body_t

Confirmation message body for sl_wfx_get_ap_client_signal_strength_cnf_t .

Definition at line 3082 of file wfm_cmd_api.h .

Data Fields
uint32_t	rcpi	Received Channel Power Indicator (RCPI) of the client. See Received Channel Power Indicator for further details.
uint32_t	status	Status of the get request. WFM_STATUS_SUCCESS : the get request was completed. any other value : the get request failed. See WFM_STATUS for enumeration values.

◆ sl_wfx_get_ap_client_signal_strength_cnf_t

struct sl_wfx_get_ap_client_signal_strength_cnf_t

Confirmation message for sl_wfx_get_ap_client_signal_strength_cnf_t .

Definition at line 3101 of file wfm_cmd_api.h .

Data Fields
sl_wfx_get_ap_client_signal_strength_cnf_body_t	body	Confirmation message body.
sl_wfx_header_t	header	Common message header.

◆ sl_wfx_disconnect_req_t

struct sl_wfx_disconnect_req_t

Request message for disconnecting from a Wi-Fi network.

The host can use this request to initiate a disconnection from a Wi-Fi network.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

◆ sl_wfx_get_signal_strength_req_t

struct sl_wfx_get_signal_strength_req_t

Request message for retrieving the signal strength of connection.

The host can use this request to retrieve the signal strength of the connection.

Interface mode	Request allowed
idle	No
station	Yes
AP	No
IBSS	No

◆ sl_wfx_stop_ap_req_t

struct sl_wfx_stop_ap_req_t

Request message for stopping the started Wi-Fi network.

The host can use this request to stop the started Wi-Fi network.

Interface mode	Request allowed
idle	No
station	No
AP	Yes
IBSS	No

◆ sl_wfx_stop_ap_ind_t

struct sl_wfx_stop_ap_ind_t

Indication message used to signal the completion of a stop operation.

The device will send this indication to signal the stop request initiated with sl_wfx_stop_ap_req_t has been completed. The indication is also sent when the started network has encountered a fatal error.

◆ sl_wfx_stop_scan_req_t

struct sl_wfx_stop_scan_req_t

Request message for stopping an ongoing scan.

The host can use this request to stop an ongoing scan operation.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	No
IBSS	No

◆ sl_wfx_leave_ibss_req_t

struct sl_wfx_leave_ibss_req_t

Request message for disconnecting from an IBSS network.

The host can use this request to disconnect from an IBSS network.

Interface mode	Request allowed
idle	No
station	No
AP	No
IBSS	Yes

◆ sl_wfx_leave_ibss_ind_t

struct sl_wfx_leave_ibss_ind_t

Indication message used to signal the completion of a disconnect operation.

The device will send this indication to signal the disconnect request initiated with sl_wfx_leave_ibss_req_t has been completed. The indication is also sent when the network has encountered a fatal error.

◆ sl_wfx_get_max_tx_power_req_t

struct sl_wfx_get_max_tx_power_req_t

Request message for getting the maximum transmit power.

The host can use this request to get the current value of maximum transmit power.

Interface mode	Request allowed
idle	Yes
station	Yes
AP	Yes
IBSS	Yes

◆ sl_wfx_get_pmk_req_t

struct sl_wfx_get_pmk_req_t

Request message for getting the Pairwise Master Key (PMK).

The host can use this request to retrieve the Pairwise Master Key (PMK) used to connect to the current secure network. PMK can be given in the next sl_wfx_connect_req_t message to speed up connection process. See Passwords and pass phrases for further details.

Interface mode	Request allowed
idle	No
station	Yes
AP	Yes
IBSS	No

API messagesFULL_MAC_API

Data Structures