Additional Status Codes#

OS operation failed.

Bootup options not saved.

Bootup options checksum failed.

Bootloader version mismatch.

Waiting for board ready.

Invalid firmware.

Invalid option.

SPI busy.

Card ready not received.

Firmware upgrade timed out.

Does not exist.

Not authenticated.

Not keyed.

IOCTL fail.

Buffer unavailable temporarily.

Buffer unavailable permanently.

WPS PBC overlap.

Connection lost.

Cannot add extra event handler.

Error manipulating a semaphore.

Packet retrieval cancelled due to flow control.

Packet retrieval cancelled due to lack of bus credits.

Packet retrieval cancelled due to no pending packets.

Core disabled due to no clock.

Core disabled - in reset.

Unsupported function.

Error writing to WLAN register.

SDIO bus failed to come up.

Join not finished yet.

Specified network was not found.

Join status error.

Unknown interface specified.

Error during SDIO receive.

Hardware tag header corrupt.

Failed to allocate a buffer to receive into.

Error reading a bus hardware register.

Failed to create a new thread.

Error manipulating a queue.

Error moving the current pointer of a buffer.

Error setting size of packet buffer.

Null stack pointer passed when non null was required.

Error deleting a thread.

Failed to put a thread to sleep.

Failed to allocate a packet buffer.

Requested interface is not active.

Requested delay is too long.

Duty cycle is outside limit 0 to 0.

Returned pmk was the wrong length.

AP security type was unknown.

AP not allowed to use WEP - use Open instead.

WPA / WPA2 key length must be between 8 & 64 bytes.

Specified filter id not found.

Failed to read 0xfeedbead SPI id from chip.

Mismatch in sizes between SPI and SDPCM header.

Attempt to register a multicast address twice.

SDIO transfer failed too many times.

Null Pointer argument passed to function.

Error deleting a thread.

Semaphore/Mutex wait has been aborted.

Unaligned message in the queue.

Error while Mutex operation.

Error while decryption over secure link.

Error while renegotiation of key over secure link.

Invalid opermode provided.

Invalid security encryption method provided.

TRNG duplicate elements error.

Return when parameter passed to Crypto SAPI is invalid.

Return in AEAD (CCM, GCM, Chachapoly) decryption function, when MAC generated during decryption does not match the MAC passed.

Scan command issued while device is already associated with an access point.

No AP found.

Wrong PSK is issued while the device client tries to join an access point with WEP security enabled.

Invalid band.

Association not done or in unassociated state.

De-authentication received from AP.

Failed to associate to access point during "Join".

Invalid channel.

Authentication failure during "Join". Unable to find AP during join which was found during scan.

Missed beacon from AP during join.

Non-existent MAC address supplied in "Disassociate" command.

EAP configuration is not done.

Memory allocation failed or Store configuration check sum failed.

Information is wrong or insufficient in join command.

Not an AP interface.

Push button command given before the expiry of previous push button command.

Access point not found. Rejoin failure.

Frequency not supported.

Invalid opermode.

EAP configuration failed.

P2P configuration failed.

Unable to start Group Owner negotiation.

Join timeout.

Command given in incorrect state.

Query GO parameters issued in incorrect operating mode.

Unable to form access point.

Wrong scan input parameters supplied to "Scan" command.

Command issued during re-join in progress.

Wrong parameters the command request.

Provision discovery failed in P2P.

PSK length less than 8 bytes or more than 63 bytes.

Failed to clear or to set the Enterprise Certificate (Set Certificate).

P2P Go negotiation failed.

Association between nodes failed in P2P WPS mode due to timeout.

If a command is issued by the Host when the device is internally executing auto-join or auto-create.

WEP key is of wrong length.

ICMP request timeout error.

ICMP data size exceeds maximum limit.

Send data packet exceeded the limit or length that is mentioned (or) MQTT publish data and publish data length mismatched (or) MQTT Send data packet exceeded the limit.

ARP cache entry not found.

UART command timeout happened.

Fixed data rate is not supported by connecting AP.

Maximum length exceeded of username/password/client_id/topic in MQTT.

Wrong WPS PIN.

Wrong WPS PIN length.

Wrong PMK length.

SSID not present for PMK generation.

SSID incorrect for PMK generation(more than 32 bytes).

Band not supported.

User store configuration invalid length.

Error in length of the command (Exceeds number of characters is mentioned in the PRM).

Data packet dropped.

WEP key not given.

Error in length of store config profile.

PSK or PMK not given.

Security mode given in join command is invalid.

Beacon miscount reaches max beacon miscount (De-authentication due to beacon miss).

De-authentication received from supplicant.

De-authentication received from AP after channel switching.

Synchronization missed.

Authentication timeout occurred.

Association timeout.

BG scan in given channels is not allowed.

Scanned SSID and SSID given in join are not matching.

Given number of clients exceeded max number of stations supported.

Given HT capabilities are not supported.

UART Flow control not supported.

ZB/BT/BLE packet received and protocol is not enabled.

MGMT pkt dropped.

Invalid RF current mode.

Power save support is not present for a given interface.

Concurrent AP in connected state.

Connected AP or Station channel mismatch.

IAP co processor error.

WPS not supported in current operating mode.

Concurrent AP doesn't have same channel as connected station channel.

PBC session overlap error.

BT feature bit map invalid.

4/4 confirmation of 4 way handshake failed.

MAC address not present in MAC based join.

Concurrent mode, both AP and client should be up, to enable configuration.

Certificate load not allowed in flash.

Certificate load not allowed in RAM.

Certificate load failed due to wrong index.

AP HT caps not enabled.

Address family not supported by protocol.

Invalid beacon interval or DTIM period provided.

Invalid range of the configuration provided.

RTS THRESHOLD Config type is invalid.

Error with MQTT command.

listen interval in power save is greater than that of join.

WLAN radio deregistered.

SAE failure due to multiple confirm frames from AP.

AP does not support the EC-group set by station.

Occurs when HE_PARAMS_SUPPORT and SLI_SI91X_ENABLE_TWT_FEATURE macros are not enabled.

Occurs when user tries to give TWT config command when there is an already active TWT session.

Occurs when TWT teardown command is given with a flow ID that does not match existing session flow ID.

Occurs when teardown command is given while there is no active session.

This error code indicates that TWT session is not feasible. It is thrown only when TWT Auto Selection API is used.

AP does not support TWT information frame reception.

No active TWT agreement corresponding to given flow id.

Suspend or resume TWT action is in progress.

TWT information frame packet creation failed in firmware.

The Server does not support the level of the MQTT protocol requested by the Client.

The Client identifier is correct UTF-8 but not allowed by the Server.

The Network Connection has been made but the MQTT service is unavailable.

The data in the user name or password is malformed.

The Client is not authorized to connect.

Duplicate entry exists in DNS server table.

Memory error: No memory available.

Invalid characters in JSON object.

Update commands: No such key found.

No such file found: Re-check filename.

No corresponding web page exists with same filename.

Space unavailable for new file.

Invalid input data, Re-check filename, lengths, etc.

Space unavailable for new file.

Existing file overwrite: Exceeds size of previous file. Use erase and try again.

No such file found. Re-check filename.

Memory Error: No memory available.

Received more web page data than the total length initially specified.

Error in set region command.

Web page current chunk length is incorrect.

Error in AP set region command.

Error in AP set region command parameters.

Region code not supported.

Error in extracting country region from beacon.

Device does not have selected region support.

SSL/TLS context create failed.

SSL/TLS handshake failed. Socket will be closed.

SSL/TLS max sockets reached.

FTP client is not connected.

Cipher set failure.

HTTP credentials maximum length exceeded.

Feature not supported.

Unable to write to flash OR flash data verification failed.

Calibration data verification failed.

SNMP internal error.

SNMP invalid IP protocol error.

No data received or receive timeout.

Insufficient data for converting NTP time to mm-dd-yy time format.

Invalid SNTP server address.

SNTP client not started.

SNTP server not available. Client will not get any time update service from current server.

SNTP server authentication failed.

Internal error.

Entry not found for multicast IP address.

No more entries found for multicast.

IP address error.

Socket already bound.

Port not available.

Socket is not created.

ICMP request failed.

Maximum listen sockets reached.

DHCP duplicate listen.

Port not in closed state.

Socket is closed or in process of closing.

Process in progress.

Trying to connect non-existing TCP server socket.

Error in length of the command ('Exceeds number of characters' is mentioned in the PRM).

Wrong packet info.

Socket is still bound.

No free port.

Invalid port.

Feature not supported.

Socket is not in connected state. Disconnected from server. In case of FTP, user need to give destroy command after receiving this error.

POP3 session creation failed / POP3 session got terminated.

DHCPv6 handshake failure.

DHCP invalid IP response.

SMTP authentication error.

No DNS server was specified, SMTP over size mail data.

SMTP invalid server reply.

DNS query failed, SMTP internal error.

Bad DNS address, SMTP server error code received.

SMTP invalid parameters.

SMTP packet allocation failed.

SMTP Greet reply failed.

Parameter error, SMTP hello reply error.

SMTP mail reply error.

SMTP RCPT reply error.

SMTP message reply error.

SMTP data reply error.

SMTP authentication reply error.

SMTP server error reply.

DNS duplicate entry.

SMTP oversize server reply.

SMTP client not initialized.

DNS IPv6 not supported.

Invalid mail index for POP3 mail retrieve command.

SSL/TLS handshake failed.

FTP client is not connected or disconnected with the FTP server.

FTP client is not disconnected.

FTP file is not opened.

SSL/TLS handshake timeout or FTP file is not closed.

Expected [1XX response from FTP server but not received].

Expected [2XX response from FTP server but not received].

Expected [22X response from FTP server but not received].

Expected [23X response from FTP server but not received].

Expected [3XX response from FTP server but not received].

Expected [33X response from FTP server but not received].

HTTP timeout.

HTTP failed.

HTTP timeout for HTTP PUT client.

Authentication error.

Invalid packet length. Content length and received data length is mismatching.

Server responds before HTTP client request is complete.

HTTP/HTTPS password is too long.

MQTT ping time out error.

MQTT command sent in incorrect state.

MQTT ACK time out error.

POP3 error for invalid mail index.

Listening TCP socket in device is not connected to the remote peer, or the LTCP socket is not yet opened in the device.

Sockets not available. The error comes if the host tries to open more than 10 sockets.

HTTP OTAF invalid packet.

TCP_IP initialization failed.

Cannot create IP in same interface in concurrent mode.

HTTP OTAF incomplete packet.

Store configuration profile type mismatch or invalid profile type.

MQTT remote terminate error.

Byte stuffing error in AT mode.

Invalid command (e.g. parameters insufficient or invalid in the command). Invalid operation (e.g. power save command with the same mode given twice, accessing wrong socket, creating more than allowed sockets ).

HTTP OTAF no packet.

TCP socket is not connected.

Station count exceeded max station supported.

Unable to send TCP data.

Socket buffer too small.

Invalid content in the DNS response to the DNS resolution query.

DNS class error in response to the DNS resolution query.

DNS count error in response to the DNS resolution query.

DNS return code error in the response to the DNS resolution query.

DNS Opcode error in the response to the DNS resolution query.

DNS id mismatch between DNS resolution request and response.

An invalid input to the DNS resolution query.

DNS response was timed out.

ARP request failure.

Unable to update TCP window.

DHCP lease time expired.

DHCP handshake failure.

This error is issued when WebSocket creation failed.

This error is issued when device tried to connect to a non-existent TCP server socket on the remote side.

This error is issued when tried to close non-existent socket. or invalid socket descriptor.

Invalid socket parameters.

Feature not supported.

Socket already open.

Attempt to open more than the maximum allowed number of sockets.

Data length exceeds mss.

DUT unable to configure IP address due to IP conflict.

Feature not enabled.

DHCP server not set in AP mode.

Error in AP set region command parameters.

SSL/TLS not supported.

JSON not supported.

Invalid operating mode.

Invalid socket configuration parameters.

Web socket creation timeout.

Parameter maximum allowed value is exceeded.

Socket read timeout.

Invalid command in sequence.

DNS response timed out.

HTTP socket creation failed.

TCP socket close command is issued before getting the response of the previous close command.

'Wait On Host' feature not enabled.

Store configuration checksum validation failed.

TCP keep alive timed out.

TCP ACK failed for TCP SYN-ACK.

Memory limit exceeded in a given operating mode.

Memory limit exceeded in an operating mode during auto join/create.

PUF operation is blocked.

PUF activation code invalid.

PUF input parameters invalid.

PUF in error state.

PUF operation not allowed.

PUF operation failed.

Auto join or user store configuration going on.

Improper RSNIE from AP to station.

Reached maximum SNTP invalid attempts.

Frequency offset sent is zero.

Frequency offset specified goes beyond upper or lower limits and indicates that frequency offset cannot be changed further.