Custom Feature Bitmap#

SL_SI91X_CUSTOM_FEAT_DISABLE_GATEWAY_IN_RSI_AP#

#define SL_SI91X_CUSTOM_FEAT_DISABLE_GATEWAY_IN_RSI_AP

BIT(2)

Disables gateway config sent to STA from RSI AP.

Note

• Bits 0 -1 are reserved

• If this bit is set to 1, the DHCP server behavior changes when the device is in AP mode. The DHCP server, when it assigns IP addresses to the client nodes, does not send out a Gateway address, and sends only the assigned IP and Subnet values to the client. It is highly recommended to keep this value at '0' as the changed behavior is required in only very specialized use cases and not in normal AP functionality. The default value of this bit is '0'.

SL_SI91X_CUSTOM_FEAT_SOC_CLK_CONFIG_160MHZ#

#define SL_SI91X_CUSTOM_FEAT_SOC_CLK_CONFIG_160MHZ

BIT(4)

To configure the clock for NWP SOC 160Mhz If higher performance is needed (like High throughput) then this configuration is needed.

Note

• Need to set pll_mode to 1 in feature frame command

SL_SI91X_CUSTOM_FEAT_AP_IN_HIDDEN_MODE#

#define SL_SI91X_CUSTOM_FEAT_AP_IN_HIDDEN_MODE

BIT(5)

If this bit is set, AP is created in hidden mode This bit is valid only in case of AP mode.

SL_SI91X_CUSTOM_FEAT_DNS_SERVER_IN_DHCP_OFFER#

#define SL_SI91X_CUSTOM_FEAT_DNS_SERVER_IN_DHCP_OFFER

BIT(6)

DNS server IP address in DHCP offer response in AP mode.

SL_SI91X_CUSTOM_FEAT_DFS_CHANNEL_SUPPORT#

#define SL_SI91X_CUSTOM_FEAT_DFS_CHANNEL_SUPPORT

BIT(8)

Support for scanning in DFS channels() in 5GHZ band This bit is valid in WiFi client mode.

Note

• Bit 7 is reserved

• It's mandatory to set the region before scanning DFS channel.

SL_SI91X_CUSTOM_FEAT_LED_FEATURE#

#define SL_SI91X_CUSTOM_FEAT_LED_FEATURE

BIT(9)

If this bit is set, it enables the LED blinking feature after module initialization.

LED (GPIO_16) is used for this feature and blinks when a TX packet is sent or when we get a unicast packet addressed to our MAC.

SL_SI91X_CUSTOM_FEAT_ASYNC_CONNECTION_STATUS#

#define SL_SI91X_CUSTOM_FEAT_ASYNC_CONNECTION_STATUS

BIT(10)

If this bit is enabled, module indicates the host the WLAN connection status asynchronously This bit is valid in case of Wi-Fi client mode.

SL_SI91X_CUSTOM_FEAT_WAKE_ON_WIRELESS#

#define SL_SI91X_CUSTOM_FEAT_WAKE_ON_WIRELESS

BIT(11)

Wake on wireless indication in UART mode.

SL_SI91X_CUSTOM_FEAT_ENABLE_AP_BLACKLIST#

#define SL_SI91X_CUSTOM_FEAT_ENABLE_AP_BLACKLIST

BIT(12)

Enables AP blacklisting in STA mode.

Note

• By default client maintains AP blacklist internally to avoid some access points. To bypass AP blacklist feature in client mode during roaming or rejoin, this feature should be enabled.

SL_SI91X_CUSTOM_FEAT_MAX_NUM_OF_CLIENTS#

#define SL_SI91X_CUSTOM_FEAT_MAX_NUM_OF_CLIENTS

(max_num_of_clients)

Number of clients to support in AP/WFD mode Bit 13 -16 are used to set MAX_NUM_OF_CLIENTS.

SL_SI91X_CUSTOM_FEAT_ROAM_WITH_DEAUTH_OR_NULL_DATA#

#define SL_SI91X_CUSTOM_FEAT_ROAM_WITH_DEAUTH_OR_NULL_DATA

BIT(17)

select between de-authentication or null data (with power management bit set) based roaming.

SL_SI91X_CUSTOM_FEAT_TRIGGER_AUTO_CONFIG#

#define SL_SI91X_CUSTOM_FEAT_TRIGGER_AUTO_CONFIG

BIT(20)

Trigger Auto Configuration.

Note

• Bit 18 - 19 are reserved

SL_SI91X_CUSTOM_FEAT_LIMIT_PACKETS_PER_STA#

#define SL_SI91X_CUSTOM_FEAT_LIMIT_PACKETS_PER_STA

BIT(22)

In AP mode, If set only two packets per STA will be buffered when STA is in PS.

Note

• Bit 21 is reserved

SL_SI91X_CUSTOM_FEAT_HTTP_HTTPS_AUTH#

#define SL_SI91X_CUSTOM_FEAT_HTTP_HTTPS_AUTH

BIT(23)

Bit to set HTTP Authentication.

SL_SI91X_CUSTOM_FEAT_SOC_CLK_CONFIG_120MHZ#

#define SL_SI91X_CUSTOM_FEAT_SOC_CLK_CONFIG_120MHZ

BIT(24)

To configure the clock for NWP SOC 120Mhz.

If higher performance is needed(like High throughput) then this configuration is needed Note

• Need to set pll_mode to 1 in feature frame command

SL_SI91X_CUSTOM_FEAT_HTTP_SERVER_CRED_TO_HOST#

#define SL_SI91X_CUSTOM_FEAT_HTTP_SERVER_CRED_TO_HOST

BIT(25)

HTTP server credentials to host in get configuration command.

SL_SI91X_CUSTOM_FEAT_REJECT_CONNECT_REQ_IMMEDIATELY#

#define SL_SI91X_CUSTOM_FEAT_REJECT_CONNECT_REQ_IMMEDIATELY

BIT(26)

For a LTCP socket when maximum clients are connected if a new connection request is received, then this connection request will be rejected immediately.

Note

• By default, this bit value is zero. When BIT[26] = 0: For a LTCP socket when maximum clients are connected if a new connection request is received, then this connection request will not be rejected. Instead device will maintain this connection request in LTCP pending list. This request will be served when any of the connected client is disconnected. When BIT[26] = 1: For a LTCP socket when maximum clients are connected if a new connection request is received, then this connection request will be rejected immediately. Device will not maintain this connection request in LTCP pending list.

SL_SI91X_CUSTOM_FEAT_DUAL_BAND_ROAM_VCSAFD#

#define SL_SI91X_CUSTOM_FEAT_DUAL_BAND_ROAM_VCSAFD

BIT(27)

Enables Dual band roaming and vcsafd feature.

SL_SI91X_CUSTOM_FEAT_RTC_FROM_HOST#

#define SL_SI91X_CUSTOM_FEAT_RTC_FROM_HOST

BIT(28)

Real time clock from host.

SL_SI91X_CUSTOM_FEAT_BT_IAP#

#define SL_SI91X_CUSTOM_FEAT_BT_IAP

BIT(29)

Custom feat BT IAP.

SL_SI91X_CUSTOM_FEAT_EXTENTION_VALID#

#define SL_SI91X_CUSTOM_FEAT_EXTENTION_VALID

BIT(31)

Extention valid to use Extended custom feature bitmap.

Note

• Bit 30 is reserved