Server#

rsi_ble_add_service#

int32_t rsi_ble_add_service (uuid_t service_uuid, rsi_ble_resp_add_serv_t * p_resp_serv)

Add a new service to the local GATT Server. This is a blocking API.

• Pre-conditions:

  • Call sl_wifi_init() before calling this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4D08 - Profile record full

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes .

rsi_ble_add_attribute#

int32_t rsi_ble_add_attribute (rsi_ble_req_add_att_t * p_attribute)

Add a new attribute to a specific service. This is a blocking API.

• Pre-conditions: Call sl_wifi_init() before calling this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4D09 - Attribute record full
    

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes .

rsi_ble_set_local_att_value#

int32_t rsi_ble_set_local_att_value (uint16_t handle, uint16_t data_len, const uint8_t * p_data)

Change the local attribute value. This is a blocking API. When the gatt_database is present, the value can be altered using the "rsi_ble_set_local_att_value" API. This means the gatt_database value can be modified at any point following its creation. 

• Pre-conditions: rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4D06 - Attribute record not found

  • 0x4E60 - Invalid Handle Range

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes .

• This API can only be used if the service is maintained inside the firmware.

• The services which are maintained by firmware must follow the below rules.

• Rule 1: The attribute_data_size is less than 20 bytes during the service_creation

• Rule 2: while creating the service, don't use the RSI_BLE_ATT_MAINTAIN_IN_HOST bit in the RSI_BLE_ATT_CONFIG_BITMAP macro.

• Rule 3: The data_len must be less than or equal to the dat_length mentioned while creating the service/attribute

• Rule 4: The rsi_ble_notify_value() API should be used instead of rsi_ble_set_local_att_value() to update the SiWx91x local database when the services are maintained in the host itself.

rsi_ble_set_wo_resp_notify_buf_info#

int32_t rsi_ble_set_wo_resp_notify_buf_info (const uint8_t * dev_addr, uint8_t buf_mode, uint8_t buf_cnt)

Configure the buf mode for Notify and WO response commands for the remote device. This is a blocking API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4D05 - BLE socket not available

  • 0x4D06 - Attribute record not found

  • 0x4E60 - Invalid Handle Range

  • 0x4E63 - BLE Buffer Count Exceeded

  • 0x4E64 - BLE Buffer already in use
    

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes .

rsi_ble_notify_value#

int32_t rsi_ble_notify_value (const uint8_t * dev_addr, uint16_t handle, uint16_t data_len, const uint8_t * p_data)

Notify the local value to the remote device. This is a blocking API. If the API returns RSI_ERROR_BLE_DEV_BUF_FULL (-31) error then wait until the rsi_ble_on_le_more_data_req_t event gets received from the module.

• Pre-conditions:

  • rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4A0D - Invalid attribute value length

  • 0x4D05 - BLE socket not available

  • 0x4D06 - Attribute record not found

  • 0x4E60 - Invalid Handle Range

  • 0x4E65 - Invalid Attribute Length When Small Buffer Mode is Configured
    

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

• The rsi_ble_notify_value() API should be used instead of rsi_ble_set_local_att_value() to update the SiWx91x local database when the services are maintained in the host itself.

rsi_ble_indicate_value#

int32_t rsi_ble_indicate_value (const uint8_t * dev_addr, uint16_t handle, uint16_t data_len, const uint8_t * p_data)

Indicate the local value to the remote device. This is a blocking API and can unblock the application on the reception of the callback functions either rsi_ble_on_event_indicate_confirmation_t.

• Pre-conditions:

  • rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4D05 - BLE socket not available

  • 0x4E60 - Invalid Handle Range

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

rsi_ble_get_local_att_value#

int32_t rsi_ble_get_local_att_value (uint16_t handle, rsi_ble_resp_local_att_value_t * p_resp_local_att_val)

Get the local attribute value. This is a blocking API.

• Pre-conditions: rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4046 - Invalid Arguments

  • 0x4D06 - Attribute record not found

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

• This API can only be used if the service is maintained inside the firmware. The services which are maintained by firmware must follow the below rules.

• Rule 1: The attribute_data_size is less than 20 bytes during the service_creation

• Rule 2: While creating the service, don't use the RSI_BLE_ATT_MAINTAIN_IN_HOST bit in the RSI_BLE_ATT_CONFIG_BITMAP macro.

rsi_ble_gatt_read_response#

int32_t rsi_ble_gatt_read_response (uint8_t * dev_addr, uint8_t read_type, uint16_t handle, uint16_t offset, uint16_t length, const uint8_t * p_data)

Send the response for the read request received from the remote device This is a blocking API.

• Pre-conditions:

  • rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4D04 - BLE not connected

Note

• It's necessary to use the "rsi_ble_gatt_read_response" API when the services are managed by the Application/Host itself.

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

rsi_ble_remove_gatt_service#

int32_t rsi_ble_remove_gatt_service (uint32_t service_handler)

Remove the GATT service record. This is a blocking API.

• Pre-conditions: GATT database needs to be present, GATT Database value can be modified at any point following its creation.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4D0A - BLE profile not found (profile handler invalid)

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

rsi_ble_remove_gatt_attibute#

int32_t rsi_ble_remove_gatt_attibute (uint32_t service_handler, uint16_t att_hndl)

Remove the GATT attribute record. This is a blocking API.

• Pre-conditions: GATT database needs to be present, GATT Database value can be modified at any point following its creation.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4D06 - Attribute record not found
    

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes

rsi_ble_att_error_response#

int32_t rsi_ble_att_error_response (uint8_t * dev_addr, uint16_t handle, uint8_t opcode, uint8_t err)

Send attribute error response for any of the att request. This is a blocking API.

• Pre-conditions: rsi_ble_connect() API needs to be called before this API.

Returns

• The following values are returned:

  • 0 - Success

  • Non-Zero Value - Failure

  • 0x4D04 - BLE not Connected
    

  • 0x4E62 - Invalid Parameters

Note

• Refer to the Status Codes section for the above error codes at wiseconnect-status-codes