RAIL_IEEE802154_MAX_ADDRESSES#

#define RAIL_IEEE802154_MAX_ADDRESSES

(3U)

The maximum number of allowed addresses of each type.

RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_BYTES#

#define RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_BYTES

(0U)

RX channel switching buffer size, in bytes.

SLI_LIBRARY_BUILD

RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_ALIGNMENT_TYPE#

#define RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_ALIGNMENT_TYPE

uint32_t

Fixed-width type indicating the needed alignment for RX channel switching buffer.

RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_ALIGNMENT#

#define RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_ALIGNMENT

(sizeof(RAIL_IEEE802154_RX_CHANNEL_SWITCHING_BUF_ALIGNMENT_TYPE))

Alignment that is needed for RX channel switching buffer.

RAIL_IEEE802154_RX_CHANNEL_SWITCHING_NUM_CHANNELS#

#define RAIL_IEEE802154_RX_CHANNEL_SWITCHING_NUM_CHANNELS

(2U)

Maximum numbers of channels supported for RX channel switching.

RAIL_IEEE802154_E_OPTIONS_NONE#

#define RAIL_IEEE802154_E_OPTIONS_NONE

0UL

A value representing no options enabled.

RAIL_IEEE802154_E_OPTIONS_DEFAULT#

#define RAIL_IEEE802154_E_OPTIONS_DEFAULT

RAIL_IEEE802154_E_OPTIONS_NONE

All options disabled by default .

RAIL_IEEE802154_E_OPTION_GB868#

#define RAIL_IEEE802154_E_OPTION_GB868

(1UL << RAIL_IEEE802154_E_OPTION_GB868_SHIFT)

An option to enable/disable 802.15.4E-2012 features needed for GB868.

When not promiscuous, RAIL normally accepts only 802.15.4 MAC frames whose MAC header Frame Version is 0 (802.15.4-2003) or 1 (802.15.4-2006), filtering out higher Frame Version packets (as RAIL_RX_PACKET_ABORT_FORMAT). Enabling this feature additionally allows Frame Version 2 (802.15.4E-2012 / 802.15.4-2015) packets to be accepted and passed to the application.

Note

• Enabling this feature also automatically enables RAIL_IEEE802154_E_OPTION_ENH_ACK on platforms that support that feature.

• This feature does not automatically enable receiving Multipurpose frames; that can be enabled via RAIL_IEEE802154_AcceptFrames()'s RAIL_IEEE802154_ACCEPT_MULTIPURPOSE_FRAMES.

RAIL_IEEE802154_E_OPTION_ENH_ACK#

#define RAIL_IEEE802154_E_OPTION_ENH_ACK

(1UL << RAIL_IEEE802154_E_OPTION_ENH_ACK_SHIFT)

An option to enable/disable 802.15.4E-2012 features needed for Enhanced ACKs.

This option requires that RAIL_IEEE802154_E_OPTION_GB868 also be enabled, and is enabled automatically on platforms that support this feature. It exists as a separate flag to allow runtime detection of whether the platform supports this feature or not.

When enabled, only an Enhanced ACK is expected in response to a transmitted ACK-requesting 802.15.4E Version 2 frame. RAIL only knows how to construct 802.15.4 Immediate ACKs but not Enhanced ACKs.

This option causes RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND to be issued for ACK-requesting Version 2 MAC Command frames, Data frames (if RAIL_IEEE802154_EnableDataFramePending() is enabled), and Multipurpose Frames (if RAIL_IEEE802154_ACCEPT_MULTIPURPOSE_FRAMES is enabled).

The application is expected to handle this event by calling RAIL_GetRxIncomingPacketInfo() and parsing the partly-received incoming frame to determine the type of ACK needed:

• If an Immediate ACK, determine Frame Pending needs based on the packet type and addressing information and call RAIL_IEEE802154_ToggleFramePending() if necessary;

• If an Enhanced ACK, generate the complete payload of the Enhanced ACK including any Frame Pending information and call RAIL_IEEE802154_WriteEnhAck() in time for that Enhanced ACK to be sent. If not called in time, RAIL_EVENT_TXACK_UNDERFLOW will likely result. Note that if 802.15.4 MAC-level encryption is used with Version 2 frames, the application should decrypt the MAC Command byte in a MAC Command frame to determine whether it is a Data Request or other MAC Command.

An application can also enable RAIL_IEEE802154_EnableEarlyFramePending() if the protocol doesn't need to examine the MAC Command byte of MAC Command frames but can infer it to be a Data Request.

On 802.15.4E GB868 platforms that lack this support, legacy Immediate ACKs are sent/expected for received/transmitted ACK-requesting 802.15.4E Frame Version 2 frames; calls to RAIL_IEEE802154_WriteEnhAck() have no effect. Attempting to use this feature via RAIL_IEEE802154_ConfigEOptions() returns an error.

RAIL_IEEE802154_E_OPTION_IMPLICIT_BROADCAST#

#define RAIL_IEEE802154_E_OPTION_IMPLICIT_BROADCAST

(1UL << RAIL_IEEE802154_E_OPTION_IMPLICIT_BROADCAST_SHIFT)

An option to enable/disable 802.15.4E-2012 macImplicitBroadcast feature.

When enabled, received Frame Version 2 frames without a destination PAN ID or destination address are treated as though they are addressed to the broadcast PAN ID and broadcast short address. When disabled, such frames are filtered unless the device is the PAN coordinator and appropriate source addressing information exists in the packet

RAIL_IEEE802154_E_OPTIONS_ALL#

#define RAIL_IEEE802154_E_OPTIONS_ALL

0xFFFFFFFFUL

A value representing all possible options.

RAIL_IEEE802154_G_OPTIONS_NONE#

#define RAIL_IEEE802154_G_OPTIONS_NONE

0UL

A value representing no options enabled.

RAIL_IEEE802154_G_OPTIONS_DEFAULT#

#define RAIL_IEEE802154_G_OPTIONS_DEFAULT

RAIL_IEEE802154_G_OPTIONS_NONE

All options disabled by default .

RAIL_IEEE802154_G_OPTION_GB868#

#define RAIL_IEEE802154_G_OPTION_GB868

(1UL << RAIL_IEEE802154_G_OPTION_GB868_SHIFT)

An option to enable/disable 802.15.4G-2012 features needed for GB868.

Normally RAIL supports 802.15.4-2003 and -2006 radio configurations that have the single-byte PHY header allowing frames up to 128 bytes in size. This feature must be enabled for 802.15.4G-2012 or 802.15.4-2015 SUN PHY radio configurations with the two-byte bit-reversed-length PHY header format.

While GB868 only supports whitened non-FEC non-mode-switch frames up to 129 bytes including 2-byte CRC, this option also enables:

• On platforms where RAIL_FEAT_IEEE802154_G_4BYTE_CRC_SUPPORTED is true: automatic per-packet 2/4-byte Frame Check Sequence (FCS) reception and transmission based on the FCS Type bit in the received/transmitted PHY header. This includes ACK reception and automatically-generated ACKs reflect the CRC size of the incoming frame being acknowledged (i.e., their MAC payload will be increased to 7 bytes when sending 4-byte FCS). On other platforms, only the 2-byte FCS is supported.

• On platforms where RAIL_FEAT_IEEE802154_G_UNWHITENED_RX_SUPPORTED and/or RAIL_FEAT_IEEE802154_G_UNWHITENED_TX_SUPPORTED are true: automatic per-packet whitened/unwhitened reception and transmission, respectively, based on the Data Whitening bit in the received/transmitted PHY header. This includes ACK reception and automatically-generated ACKs which reflect the whitening of the incoming frame being acknowledged. On other platforms, only whitened frames are supported.

• Support for frames up to 2049 bytes per the radio configuration's maximum packet length setting.

Note

• Sending/receiving whitened frames assumes the radio configuration has established an appropriate 802.15.4-compliant whitening algorithm. RAIL does not itself override the radio configuration's whitening settings other than to enable/disable it per-packet based on the packet's PHY header Data Whitening flag.

RAIL_IEEE802154_G_OPTION_DYNFEC#

#define RAIL_IEEE802154_G_OPTION_DYNFEC

(1UL << RAIL_IEEE802154_G_OPTION_DYNFEC_SHIFT)

An option to enable/disable 802.15.4G dynamic FEC feature (SUN FSK only).

The syncWord, called start-of-frame delimiter (SFD) in the 15.4 spec, indicates whether the rest of the packet is FEC encoded or not. This feature requires per-packet dual syncWord detection and specific receiver pausing. Note that this feature is only available on platforms where RAIL_IEEE802154_SUPPORTS_G_DYNFEC is true.

This option is only valid for SUN PHYs that have the FEC configured and enabled.

The syncWord used during transmit is selected with RAIL_TX_OPTION_SYNC_WORD_ID.

The syncWord corresponding to the FEC encoded mode must be SYNC1, with SYNC2 indicating non-FEC. SyncWords are set appropriately in all Sun FEC-enabled PHYs so there should never be a need to call RAIL_ConfigSyncWords() when this option is enabled.

Also, dual syncWord detection is set in all SUN FEC enabled PHYs, then there is no need to change RAIL_RX_OPTION_ENABLE_DUALSYNC .

Note

• EFR32xG12 support for 802.15.4 FEC-capable PHYs and dynamic FEC are incompatible with 802.15.4 filtering and AutoACK. RAIL_IEEE802154_Config_t::promiscuousMode must be true and RAIL_IEEE802154_Config_t::ackConfig's RAIL_AutoAckConfig_t::enable must be false on these platforms when using a FEC-capable PHY.

RAIL_IEEE802154_G_OPTION_WISUN_MODESWITCH#

#define RAIL_IEEE802154_G_OPTION_WISUN_MODESWITCH

(1UL << RAIL_IEEE802154_G_OPTION_WISUN_MODESWITCH_SHIFT)

An option to enable/disable Wi-SUN Mode Switch feature.

This feature consists in switching to a new PHY mode with a higher rate typically by sending/receiving a specific Mode Switch packet that indicates the incoming new PHY mode. The Mode Switch packet is an FSK-modulated 2-byte PHY header with no payload. Because this feature relies on specific receiver pausing, note that it is only available on platforms where RAIL_IEEE802154_SUPPORTS_G_MODESWITCH is true.

RAIL_IEEE802154_G_OPTIONS_ALL#

#define RAIL_IEEE802154_G_OPTIONS_ALL

0xFFFFFFFFUL

A value representing all possible options.

RAIL_IEEE802154_ACCEPT_BEACON_FRAMES#

#define RAIL_IEEE802154_ACCEPT_BEACON_FRAMES

(0x01)

When receiving packets, accept 802.15.4 BEACON frame types.

RAIL_IEEE802154_ACCEPT_DATA_FRAMES#

#define RAIL_IEEE802154_ACCEPT_DATA_FRAMES

(0x02)

When receiving packets, accept 802.15.4 DATA frame types.

RAIL_IEEE802154_ACCEPT_ACK_FRAMES#

#define RAIL_IEEE802154_ACCEPT_ACK_FRAMES

(0x04)

When receiving packets, accept 802.15.4 ACK frame types.

Note

• Expected ACK frame types will still be accepted regardless of this setting when waiting for an ACK after a transmit that used RAIL_TX_OPTION_WAIT_FOR_ACK and auto-ACK is enabled.

RAIL_IEEE802154_ACCEPT_COMMAND_FRAMES#

#define RAIL_IEEE802154_ACCEPT_COMMAND_FRAMES

(0x08)

When receiving packets, accept 802.15.4 COMMAND frame types.

RAIL_IEEE802154_ACCEPT_MULTIPURPOSE_FRAMES#

#define RAIL_IEEE802154_ACCEPT_MULTIPURPOSE_FRAMES

(0x20)

When receiving packets, accept 802.15.4-2015 Multipurpose frame types.

(Not supported on EFR32XG1.)

RAIL_IEEE802154_ACCEPT_STANDARD_FRAMES#

#define RAIL_IEEE802154_ACCEPT_STANDARD_FRAMES

In standard operation, accept BEACON, DATA and COMMAND frames.

Don't receive ACK frames unless waiting for ACK (i.e., only receive expected ACKs).

RAIL_IEEE802154_ToggleFramePending#

#define RAIL_IEEE802154_ToggleFramePending

RAIL_IEEE802154_SetFramePending

Alternate naming for function RAIL_IEEE802154_SetFramePending to depict it is used for changing the default setting specified by RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks in an outgoing ACK.

RAIL_IEEE802154_EnableSignalIdentifier#

#define RAIL_IEEE802154_EnableSignalIdentifier

RAIL_IEEE802154_EnableSignalDetection

Backward compatible name for the RAIL_IEEE802154_EnableSignalDetection API.

RAIL_IEEE802154_AddressLength_t#

RAIL_IEEE802154_AddressLength_t

Different lengths that an 802.15.4 address can have.

RAIL_IEEE802154_PtiRadioConfig_t#

RAIL_IEEE802154_PtiRadioConfig_t

802.15.4 PTI radio configuration mode

RAIL_IEEE802154_EOptions_t#

RAIL_IEEE802154_EOptions_t

802.15.4E-2012 options, in reality a bitmask.

RAIL_IEEE802154_GOptions_t#

RAIL_IEEE802154_GOptions_t

802.15.4G-2012 options, in reality a bitmask.

RAIL_IEEE802154_CcaMode_t#

RAIL_IEEE802154_CcaMode_t

Available CCA modes.

RAIL_IEEE802154_SignalIdentifierMode_t#

RAIL_IEEE802154_SignalIdentifierMode_t

Available Signal identifier modes.

RAIL_IEEE802154_Phy2p4GHz#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHz

Default PHY to use for 2.4 GHz 802.15.4.

Will be NULL if RAIL_SUPPORTS_PROTOCOL_IEEE802154 or RAIL_SUPPORTS_2P4GHZ_BAND is 0.

RAIL_IEEE802154_Phy2p4GHzAntDiv#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzAntDiv

Default PHY to use for 2.4 GHz 802.15.4 with antenna diversity.

Will be NULL if RAIL_SUPPORTS_PROTOCOL_IEEE802154, RAIL_SUPPORTS_2P4GHZ_BAND, or RAIL_SUPPORTS_ANTENNA_DIVERSITY is 0.

RAIL_IEEE802154_Phy2p4GHzCoex#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzCoex

Default PHY to use for 2.4 GHz 802.15.4 optimized for coexistence.

Will be NULL if RAIL_IEEE802154_SUPPORTS_COEX_PHY is 0.

RAIL_IEEE802154_Phy2p4GHzAntDivCoex#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzAntDivCoex

Default PHY to use for 2.4 GHz 802.15.4 optimized for coexistence, while supporting antenna diversity.

Will be NULL if RAIL_SUPPORTS_ANTENNA_DIVERSITY or RAIL_IEEE802154_SUPPORTS_COEX_PHY is 0.

RAIL_IEEE802154_Phy2p4GHzFem#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzFem

Default PHY to use for 2.4 GHz 802.15.4 with a configuration that supports a front-end module.

Will be NULL if RAIL_IEEE802154_SUPPORTS_FEM_PHY is 0.

RAIL_IEEE802154_Phy2p4GHzAntDivFem#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzAntDivFem

Default PHY to use for 2.4 GHz 802.15.4 with a configuration that supports a front-end module and antenna diversity.

Will be NULL if RAIL_IEEE802154_SUPPORTS_FEM_PHY or RAIL_SUPPORTS_ANTENNA_DIVERSITY is 0.

RAIL_IEEE802154_Phy2p4GHzCoexFem#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzCoexFem

Default PHY to use for 2.4 GHz 802.15.4 with a configuration that supports a front-end module and is optimized for radio coexistence.

Will be NULL if RAIL_IEEE802154_SUPPORTS_FEM_PHY or RAIL_IEEE802154_SUPPORTS_COEX_PHY is 0.

RAIL_IEEE802154_Phy2p4GHzAntDivCoexFem#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzAntDivCoexFem

Default PHY to use for 2.4 GHz 802.15.4 with a configuration that supports a front-end module and antenna diversity, and is optimized for radio coexistence.

Will be NULL if RAIL_IEEE802154_SUPPORTS_FEM_PHY, RAIL_IEEE802154_SUPPORTS_COEX_PHY, or RAIL_SUPPORTS_ANTENNA_DIVERSITY is 0.

RAIL_IEEE802154_Phy2p4GHzCustom1#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzCustom1

Default PHY to use for 2.4 GHz 802.15.4 with custom settings.

Will be NULL if RAIL_IEEE802154_SUPPORTS_CUSTOM1_PHY is 0.

RAIL_IEEE802154_PhyGB863MHz#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_PhyGB863MHz

Default PHY to use for 863MHz GB868 802.15.4.

Will be NULL if RAIL_IEEE802154_SUPPORTS_G_SUBSET_GB868 is 0.

RAIL_IEEE802154_PhyGB915MHz#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_PhyGB915MHz

Default PHY to use for 915MHz GB868 802.15.4.

Will be NULL if RAIL_IEEE802154_SUPPORTS_G_SUBSET_GB868 is 0.

RAIL_IEEE802154_Phy2p4GHzRxChSwitching#

const RAIL_ChannelConfig_t* const RAIL_IEEE802154_Phy2p4GHzRxChSwitching

Default PHY to use for 2.4 GHz 802.15.4 with RX channel switching.

Will be NULL if RAIL_IEEE802154_SUPPORTS_RX_CHANNEL_SWITCHING is 0.

RAIL_IEEE802154_Init#

RAIL_Status_t RAIL_IEEE802154_Init (RAIL_Handle_t railHandle, const RAIL_IEEE802154_Config_t * config)

Initialize RAIL for IEEE802.15.4 features.

Returns

• A status code indicating success of the function call.

This function calls the following RAIL functions to configure the radio for IEEE802.15.4 features.

Initializes the following:

• Enables IEEE802154 hardware acceleration

• Configures RAIL Auto ACK functionality

• Configures RAIL Address Filter for 802.15.4 address filtering

It saves having to call the following functions individually:

• RAIL_ConfigAutoAck()

• RAIL_SetRxTransitions()

• RAIL_SetTxTransitions()

• RAIL_WriteAutoAckFifo()

• RAIL_SetStateTiming()

• RAIL_ConfigAddressFilter()

• RAIL_EnableAddressFilter()

It must be called before most of RAIL_IEEE802154_* function.

RAIL_IEEE802154_Config2p4GHzRadio#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadio (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioAntDiv#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioAntDiv (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with antenna diversity.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports antenna diversity. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioAntDivCoex#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioAntDivCoex (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with antenna diversity optimized for radio coexistence.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports antenna diversity optimized for radio coexistence. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioCoex#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioCoex (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation optimized for radio coexistence.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports radio coexistence. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioFem#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioFem (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with a front end module.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports a front end module. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioAntDivFem#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioAntDivFem (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with antenna diversity optimized for a front end module.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports antenna diversity and a front end module. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioCoexFem#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioCoexFem (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation optimized for radio coexistence and a front end module.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports radio coexistence and a front end module. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioAntDivCoexFem#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioAntDivCoexFem (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with antenna diversity optimized for radio coexistence and a front end module.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation, but with a configuration that supports antenna diversity, radio coexistence and a front end module. It takes the place of calling RAIL_ConfigChannels. After this call, channels 11-26 will be available, giving the frequencies of those channels on channel page 0, as defined by IEEE 802.15.4-2011 section 8.1.2.2.

Note

• This call implicitly disables all RAIL_IEEE802154_GOptions_t.

RAIL_IEEE802154_Config2p4GHzRadioCustom1#

RAIL_Status_t RAIL_IEEE802154_Config2p4GHzRadioCustom1 (RAIL_Handle_t railHandle)

Configure the radio for 2.4 GHz 802.15.4 operation with custom settings.

It enables better interoperability with some proprietary PHYs, but doesn't guarantee data sheet performance.

Returns

• A status code indicating success of the function call.

This initializes the radio for 2.4 GHz operation with custom settings. It replaces needing to call RAIL_ConfigChannels. Do not call this function unless instructed by Silicon Labs.

Note

• This feature is only available on platforms where RAIL_IEEE802154_SUPPORTS_CUSTOM1_PHY is true.

RAIL_IEEE802154_ConfigGB863MHzRadio#

RAIL_Status_t RAIL_IEEE802154_ConfigGB863MHzRadio (RAIL_Handle_t railHandle)

Configure the radio for SubGHz GB868 863 MHz 802.15.4 operation.

Returns

• A status code indicating success of the function call.

This initializes the radio for SubGHz GB868 863 MHz operation. It takes the place of calling RAIL_ConfigChannels. After this call, GB868 channels in the 863 MHz band (channel pages 28, 29, and 30 – logical channels 0x80..0x9A, 0xA0..0xA8, 0xC0..0xDA, respectively) will be available, as defined by Rev 22 of the Zigbee Specification, 2017 document 05-3474-22, section D.10.2.1.3.2.

Note

• This call implicitly enables RAIL_IEEE802154_G_OPTION_GB868.

RAIL_IEEE802154_ConfigGB915MHzRadio#

RAIL_Status_t RAIL_IEEE802154_ConfigGB915MHzRadio (RAIL_Handle_t railHandle)

Configure the radio for SubGHz GB868 915 MHz 802.15.4 operation.

Returns

• A status code indicating success of the function call.

This initializes the radio for SubGHz GB868 915 MHz operation. It takes the place of calling RAIL_ConfigChannels. After this call, GB868 channels in the 915 MHz band (channel page 31 – logical channels 0xE0..0xFA) will be available, as defined by Rev 22 of the Zigbee Specification, 2017 document 05-3474-22, section D.10.2.1.3.2.

Note

• This call implicitly enables RAIL_IEEE802154_G_OPTION_GB868.

RAIL_IEEE802154_Deinit#

RAIL_Status_t RAIL_IEEE802154_Deinit (RAIL_Handle_t railHandle)

De-initialize IEEE802.15.4 hardware acceleration.

Returns

• A status code indicating success of the function call.

Disables and resets all IEE802.15.4 hardware acceleration features. This function should only be called when the radio is IDLE. This calls the following:

• RAIL_SetStateTiming(), to reset all timings to 100 us

• RAIL_EnableAddressFilter(false)

• RAIL_ResetAddressFilter()

RAIL_IEEE802154_IsEnabled#

bool RAIL_IEEE802154_IsEnabled (RAIL_Handle_t railHandle)

Return whether IEEE802.15.4 hardware acceleration is currently enabled.

Returns

• True if IEEE802.15.4 hardware acceleration was enabled to start with and false otherwise.

RAIL_IEEE802154_GetPtiRadioConfig#

RAIL_IEEE802154_PtiRadioConfig_t RAIL_IEEE802154_GetPtiRadioConfig (RAIL_Handle_t railHandle)

Return IEEE802.15.4 PTI radio config.

Returns

• PTI (Packet Trace Information) radio config ID.

RAIL_IEEE802154_SetAddresses#

RAIL_Status_t RAIL_IEEE802154_SetAddresses (RAIL_Handle_t railHandle, const RAIL_IEEE802154_AddrConfig_t * addresses)

Configure the RAIL Address Filter for 802.15.4 filtering.

Returns

• A status code indicating success of the function call. If this returns an error, the 802.15.4 address filter is in an undefined state.

Set up the 802.15.4 address filter to accept messages to the given addresses. This will return false if any of the addresses failed to be set. If NULL is passed in for addresses, all addresses will be set to their reset value.

RAIL_IEEE802154_SetPanId#

RAIL_Status_t RAIL_IEEE802154_SetPanId (RAIL_Handle_t railHandle, uint16_t panId, uint8_t index)

Set a PAN ID for 802.15.4 address filtering.

Returns

• A status code indicating success of the function call.

Set up the 802.15.4 address filter to accept messages to the given PAN ID.

RAIL_IEEE802154_SetShortAddress#

RAIL_Status_t RAIL_IEEE802154_SetShortAddress (RAIL_Handle_t railHandle, uint16_t shortAddr, uint8_t index)

Set a short address for 802.15.4 address filtering.

Returns

• A status code indicating success of the function call.

Set up the 802.15.4 address filter to accept messages to the given short address.

RAIL_IEEE802154_SetLongAddress#

RAIL_Status_t RAIL_IEEE802154_SetLongAddress (RAIL_Handle_t railHandle, const uint8_t * longAddr, uint8_t index)

Set a long address for 802.15.4 address filtering.

Returns

• A status code indicating success of the function call.

Set up the 802.15.4 address filter to accept messages to the given long address.

RAIL_IEEE802154_SetPanCoordinator#

RAIL_Status_t RAIL_IEEE802154_SetPanCoordinator (RAIL_Handle_t railHandle, bool isPanCoordinator)

Set whether the current node is a PAN coordinator.

Returns

• A status code indicating success of the function call.

If the device is a PAN Coordinator, it will accept data and command frames with no destination address. This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init(). This setting may be changed at any time when 802.15.4 hardware acceleration is enabled.

RAIL_IEEE802154_SetPromiscuousMode#

RAIL_Status_t RAIL_IEEE802154_SetPromiscuousMode (RAIL_Handle_t railHandle, bool enable)

Set whether to enable 802.15.4 promiscuous mode.

Returns

• A status code indicating success of the function call.

If promiscuous mode is enabled, no frame or address filtering steps will be performed other than checking the CRC. This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init(). This setting may be changed at any time when 802.15.4 hardware acceleration is enabled.

RAIL_IEEE802154_ConfigEOptions#

RAIL_Status_t RAIL_IEEE802154_ConfigEOptions (RAIL_Handle_t railHandle, RAIL_IEEE802154_EOptions_t mask, RAIL_IEEE802154_EOptions_t options)

Configure certain 802.15.4E-2012 / 802.15.4-2015 Frame Version 2 features.

Returns

• A status code indicating success of the function call.

This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init() or the platform does not support the feature(s). These settings may be changed at any time when 802.15.4 hardware acceleration is enabled.

RAIL_IEEE802154_ConfigGOptions#

RAIL_Status_t RAIL_IEEE802154_ConfigGOptions (RAIL_Handle_t railHandle, RAIL_IEEE802154_GOptions_t mask, RAIL_IEEE802154_GOptions_t options)

Configure certain 802.15.4G-2012 / 802.15.4-2015 SUN PHY features (only for radio configurations designed accordingly).

Returns

• A status code indicating success of the function call.

This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init(), the platform does not support the feature(s), the radio configuration is not appropriate, or the radio is not idle.

RAIL_IEEE802154_ComputeChannelFromPhyModeId#

RAIL_Status_t RAIL_IEEE802154_ComputeChannelFromPhyModeId (RAIL_Handle_t railHandle, uint8_t newPhyModeId, uint16_t * pChannel)

Compute channel to switch to given a targeted PhyMode ID in the context of Wi-SUN mode switching.

Returns

• A status code indicating success of the function call.

This function will fail if:

• the targeted PhyModeID is the same as the current PhyMode ID

• called on a platform that lacks RAIL_IEEE802154_SUPPORTS_G_MODESWITCH

• called on a platform that doesn't have 802154G options enabled by RAIL_IEEE802154_ConfigGOptions(). For newPhyModeId associated with a FSK FEC_off PHY, if dynamic FEC is activated (see RAIL_IEEE802154_G_OPTION_DYNFEC), the returned channel can correspond to the associated FSK FEC_on PHY corresponding then to PhyModeID = newPhyModeId + 16

RAILCb_IEEE802154_IsModeSwitchNewChannelValid#

RAIL_Status_t RAILCb_IEEE802154_IsModeSwitchNewChannelValid (uint32_t currentBaseFreq, uint8_t newPhyModeId, const RAIL_ChannelConfigEntry_t * configEntryNewPhyModeId, uint16_t * pChannel)

Manage forbidden channels during mode switch.

Returns

• A status code indicating success of the function call. It must return RAIL_STATUS_INVALID_PARAMETER for failure or RAIL_STATUS_NO_ERROR for success.

This function must fail if no valid channel has been found. If so, RAIL will abort the mode switch.

Note

• This callback will only be called on platforms where RAIL_IEEE802154_SUPPORTS_G_MODESWITCH is true, RAIL_IEEE802154_G_OPTION_WISUN_MODESWITCH was successfully enabled, and a valid mode switch PHY header is received.

RAIL_IEEE802154_AcceptFrames#

RAIL_Status_t RAIL_IEEE802154_AcceptFrames (RAIL_Handle_t railHandle, uint8_t framesMask)

Set which 802.15.4 frame types to accept.

Returns

• A status code indicating success of the function call.

This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init() or framesMask requests an unsupported frame type. This setting may be changed at any time when 802.15.4 hardware acceleration is enabled. Only Beacon, Data, ACK, Command, and Multipurpose (except on EFR32XG1) frames may be received. The RAIL_IEEE802154_ACCEPT_XXX_FRAMES defines may be combined to create a bitmask to pass into this function.

RAIL_IEEE802154_ACCEPT_ACK_FRAMES behaves slightly different than the other defines. If RAIL_IEEE802154_ACCEPT_ACK_FRAMES is set, the radio will accept an ACK frame during normal packet reception, but only a truly expected ACK will have its RAIL_RxPacketDetails_t::isAck true. If RAIL_IEEE802154_ACCEPT_ACK_FRAMES is not set, ACK frames will be filtered unless they're expected when the radio is waiting for an ACK.

RAIL_IEEE802154_EnableEarlyFramePending#

RAIL_Status_t RAIL_IEEE802154_EnableEarlyFramePending (RAIL_Handle_t railHandle, bool enable)

Enable early Frame Pending lookup event notification (RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND).

Returns

• A status code indicating success of the function call.

Normally, RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND is triggered after receiving the entire MAC header and MAC command byte for an ACK-requesting MAC command frame. Version 0/1 frames also require that command to be a Data Request for this event to occur. Enabling this feature causes this event to be triggered earlier to allow for more time to determine the type of ACK needed (Immediate or Enhanced) and/or perform frame pending lookup to influence the outgoing ACK by using RAIL_IEEE802154_WriteEnhAck() or RAIL_IEEE802154_ToggleFramePending().

For Frame Version 0/1 packets and for Frame Version 2 packets when RAIL_IEEE802154_E_OPTION_ENH_ACK is not in use, "early" means right after receiving the source address information in the MAC header.

For Frame Version 2 packets when RAIL_IEEE802154_E_OPTION_ENH_ACK is in use, "early" means right after receiving any Auxiliary Security header which follows the source address information in the MAC header.

This feature is useful when the protocol knows an ACK-requesting MAC Command must be a data poll without needing to receive the MAC Command byte, giving it a bit more time to adjust Frame Pending or generate an Enhanced ACK.

This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init(), or on platforms that do not support this feature. This setting may be changed at any time when 802.15.4 hardware acceleration is enabled.

RAIL_IEEE802154_EnableDataFramePending#

RAIL_Status_t RAIL_IEEE802154_EnableDataFramePending (RAIL_Handle_t railHandle, bool enable)

Enable Frame Pending lookup event notification (RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND) for MAC Data frames.

Returns

• A status code indicating success of the function call.

Normally RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND is triggered only for ACK-requesting MAC command frames. Enabling this feature causes this event to also be triggered for MAC data frames, at the same point in the packet as RAIL_IEEE802154_EnableEarlyFramePending() would trigger. This feature is necessary to support the Thread Basil-Hayden Enhanced Frame Pending feature in Version 0/1 frames, and to support Version 2 Data frames which require an Enhanced ACK.

This function will fail if 802.15.4 hardware acceleration is not currently enabled by calling RAIL_IEEE802154_Init(). This setting may be changed at any time when 802.15.4 hardware acceleration is enabled.

RAIL_IEEE802154_SetFramePending#

RAIL_Status_t RAIL_IEEE802154_SetFramePending (RAIL_Handle_t railHandle)

Change the Frame Pending bit on the outgoing legacy Immediate ACK from the default specified by RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks.

Returns

• A status code indicating success of the function call.

This function must only be called while processing the RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND if the ACK for this packet should go out with its Frame Pending bit set differently than what was specified by RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks.

It's intended only for use with 802.15.4 legacy immediate ACKs and not 802.15.4E enhanced ACKs. This will return RAIL_STATUS_INVALID_STATE if it is too late to modify the outgoing Immediate ACK.

Note

• This function is used to set the Frame Pending bit but its meaning depends on the value of RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks while transmitting ACK. If RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks is not set, then Frame Pending bit is set in outgoing ACK. Whereas, if RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks is set, then Frame Pending bit is cleared in outgoing ACK.

Therefore, this function is to be called if the frame is pending when RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks is not set or if there is no frame pending when RAIL_IEEE802154_Config_t::defaultFramePendingInOutgoingAcks is set.

RAIL_IEEE802154_GetAddress#

RAIL_Status_t RAIL_IEEE802154_GetAddress (RAIL_Handle_t railHandle, RAIL_IEEE802154_Address_t * pAddress)

Get the source address of the incoming data request.

Returns

• A status code indicating success of the function call.

This function must only be called when handling the RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND event. This will return RAIL_STATUS_INVALID_STATE if the address information is stale (i.e., it is too late to affect the outgoing ACK).

RAIL_IEEE802154_WriteEnhAck#

RAIL_Status_t RAIL_IEEE802154_WriteEnhAck (RAIL_Handle_t railHandle, const uint8_t * ackData, uint8_t ackDataLen)

Write the AutoACK FIFO for the next outgoing 802.15.4E Enhanced ACK.

Returns

• A status code indicating success of the function call.

This function sets the AutoACK data to use in acknowledging the frame being received. It must only be called while processing the RAIL_EVENT_IEEE802154_DATA_REQUEST_COMMAND, and is intended for use when packet information from RAIL_GetRxIncomingPacketInfo() indicates an 802.15.4E Enhanced ACK must be sent instead of a legacy Immediate ACK. RAIL_IEEE802154_ToggleFramePending() should not be called for an Enhanced ACK; instead the Enhanced ACK's Frame Control Field should have the Frame Pending bit set appropriately in its ackData. This will return RAIL_STATUS_INVALID_STATE if it is too late to write the outgoing ACK – a situation that will likely trigger a RAIL_EVENT_TXACK_UNDERFLOW event. When successful, the Enhanced ackData will only be sent once. Subsequent packets needing an Enhanced ACK will each need to call this function to write their ACK information.

RAIL_IEEE802154_SetRxToEnhAckTx#

RAIL_Status_t RAIL_IEEE802154_SetRxToEnhAckTx (RAIL_Handle_t railHandle, RAIL_TransitionTime_t * pRxToEnhAckTx)

Set a separate RX packet to TX state transition turnaround time for sending an Enhanced ACK.

Returns

• Status code indicating a success of the function call. An error will not update the pRxToEnhAckTx output parameter.

Normally Immediate and Enhanced ACKs are both sent using the RAIL_IEEE802154_Config_t::timings rxToTx turnaround time. If the stack needs more time to prepare an Enhanced ACK, it can call this function after RAIL_IEEE802154_Init() to set a longer turnaround time used just for Enhanced ACK transmits.

This function will fail on platforms that lack RAIL_IEEE802154_SUPPORTS_E_ENHANCED_ACK.

RAIL_IEEE802154_ConvertRssiToLqi#

uint8_t RAIL_IEEE802154_ConvertRssiToLqi (uint8_t origLqi, int8_t rssiDbm)

Convert RSSI into 802.15.4 Link Quality Indication (LQI) metric compatible with the Silicon Labs Zigbee stack.

Returns

• An LQI value (range 0..255 but not all intermediate values are possible) based on the rssiDbm and the chip's RSSI sensitivity range.

This function is compatible with RAIL_ConvertLqiCallback_t and is suitable to pass to RAIL_ConvertLqi().

RAIL_IEEE802154_ConvertRssiToEd#

uint8_t RAIL_IEEE802154_ConvertRssiToEd (int8_t rssiDbm)

Convert RSSI into 802.15.4 Energy Detection (ED) metric compatible with the Silicon Labs Zigbee stack.

Returns

• An Energy Detect value (range 0..255 but not all intermediate values are possible) based on the rssiDbm and the chip's RSSI sensitivity range.

RAIL_IEEE802154_ConfigSignalIdentifier#

RAIL_Status_t RAIL_IEEE802154_ConfigSignalIdentifier (RAIL_Handle_t railHandle, RAIL_IEEE802154_SignalIdentifierMode_t signalIdentifierMode)

Configure signal identifier for 802.15.4 signal detection.

This features allows detection of 2.4Ghz 802.15.4 signal on air. This function must be called once before RAIL_IEEE802154_EnableSignalDetection to configure and enable signal identifier.

To enable event for signal detection RAIL_ConfigEvents() must be called for enabling RAIL_EVENT_SIGNAL_DETECTED.

This function is only supported by chips where RAIL_IEEE802154_SUPPORTS_SIGNAL_IDENTIFIER and RAIL_IEEE802154_SupportsSignalIdentifier() are true.

Returns

• Status code indicating success of the function call.

RAIL_IEEE802154_EnableSignalDetection#

RAIL_Status_t RAIL_IEEE802154_EnableSignalDetection (RAIL_Handle_t railHandle, bool enable)

Enable or disable signal identifier for 802.15.4 signal detection.

RAIL_IEEE802154_ConfigSignalIdentifier must be called once before calling this function to configure and enable signal identifier. Once a signal is detected signal detection will be turned off and this function should be called to re-enable the signal detection without needing to call RAIL_IEEE802154_ConfigSignalIdentifier if the signal identifier is already configured and enabled.

This function is only supported by chips where RAIL_IEEE802154_SUPPORTS_SIGNAL_IDENTIFIER and RAIL_IEEE802154_SupportsSignalIdentifier() are true.

Returns

• Status code indicating success of the function call.

RAIL_IEEE802154_ConfigCcaMode#

RAIL_Status_t RAIL_IEEE802154_ConfigCcaMode (RAIL_Handle_t railHandle, RAIL_IEEE802154_CcaMode_t ccaMode)

Set 802.15.4 CCA mode.

This function sets the CCA mode RAIL_IEEE802154_CcaMode_t. If not called, RAIL_IEEE802154_CCA_MODE_RSSI (RSSI-based CCA) is used for CCA.

In RAIL_IEEE802154_CCA_MODE_SIGNAL, RAIL_IEEE802154_CCA_MODE_SIGNAL_OR_RSSI and RAIL_IEEE802154_CCA_MODE_SIGNAL_AND_RSSI signal identifier is enabled for the duration of LBT. If previously enabled by RAIL_IEEE802154_ConfigSignalIdentifier, the signal identifier will remain active until triggered.

This function is only supported by chips where RAIL_IEEE802154_SUPPORTS_SIGNAL_IDENTIFIER and RAIL_IEEE802154_SupportsSignalIdentifier() are true.

Returns

• Status code indicating success of the function call. An error should be returned if ccaMode is unsuppported on a given device.

RAIL_IEEE802154_ConfigRxChannelSwitching#

RAIL_Status_t RAIL_IEEE802154_ConfigRxChannelSwitching (RAIL_Handle_t railHandle, const RAIL_IEEE802154_RxChannelSwitchingCfg_t * pConfig)

Configure RX channel switching for 802.15.4.

Returns

• Status code indicating success of the function call.

This function configures RX channel switching, allowing reception of 2.4Ghz 802.15.4 signals on two different radio channels within the same PHY. (If the two channels are same, the function behaves the same as if pConfig was NULL.) This function should be called once before RAIL_StartRx and/or enabling RAIL_RX_OPTION_CHANNEL_SWITCHING.

When RAIL_RX_OPTION_CHANNEL_SWITCHING is enabled, channel switching will occur during normal listening but is suspended (and the radio is idled) when starting any kind of transmit, including scheduled or CSMA transmits. It remains suspended after a RAIL_TX_OPTION_WAIT_FOR_ACK transmit until the ACK is received or times out.

When RAIL_RX_OPTION_CHANNEL_SWITCHING is disabled after switching has been active, the radio could be left listening on either channel, so the application should call RAIL_StartRx() to put it on the desired non-switching channel.

Note

• IEEE 802.15.4 must be enabled via RAIL_IEEE802154_Init, and the radio must be in the idle state when configuring RX channel switching. A DMA channel must be allocated with RAIL_UseDma; otherwise this API will return RAIL_STATUS_INVALID_CALL. This feature also requires a PRS channel, internally allocated by the RAIL library, to use and hold onto for future use. If no PRS channel is available, the function returns RAIL_STATUS_INVALID_PARAMETER.

• When RX channel switching is active, receive sensitivity and performance are slightly impacted.

• This function internally uses RAIL_EnableCacheSynthCal to enable/disable the sequencer cache to store the synth calibration value.

• Switching is cancelled on any PHY change, so this function would need to be re-called to reestablish switching after such a change.

RAIL_IEEE802154_CalibrateIr2p4Ghz#

RAIL_Status_t RAIL_IEEE802154_CalibrateIr2p4Ghz (RAIL_Handle_t railHandle, uint32_t * imageRejection)

Calibrate image rejection for IEEE 802.15.4 2.4 GHz.

Returns

• A status code indicating success of the function call.

Some chips have protocol-specific image rejection calibrations programmed into their flash. This function will either get the value from flash and apply it, or run the image rejection algorithm to find the value.

RAIL_IEEE802154_CalibrateIrSubGhz#

RAIL_Status_t RAIL_IEEE802154_CalibrateIrSubGhz (RAIL_Handle_t railHandle, uint32_t * imageRejection)

Calibrate image rejection for IEEE 802.15.4 915 MHz and 868 MHz.

Returns

• A status code indicating success of the function call.

Some chips have protocol-specific image rejection calibrations programmed into their flash. This function will either get the value from flash and apply it, or run the image rejection algorithm to find the value.

DeprecatedPlease use RAIL_CalibrateIrAlt instead.