Bluetooth Feature Bitmap#

SL_SI91X_BT_BDR_MODE_ENABLE#

#define SL_SI91X_BT_BDR_MODE_ENABLE

BIT(0)

BT Mode Enable.

Note

• If this Bit sets, then our Controller will sends/receives the packets in 1Mbps mode. Else, Controller will be operable in both BR/EDR mode

SL_SI91X_BT_BDR_MODE_LP_CHAIN_ENABLE#

#define SL_SI91X_BT_BDR_MODE_LP_CHAIN_ENABLE

BIT(1)

BT Mode LP Chain Enable.

SL_SI91X_BT_PWR_CTRL_DISABLE#

#define SL_SI91X_BT_PWR_CTRL_DISABLE

BIT(2)

BT Power Control Disable.

Note

• To make Fixed/Adaptive Power

SL_SI91X_BT_EDR_3MBPS_DISABLE#

#define SL_SI91X_BT_EDR_3MBPS_DISABLE

BIT(8)

BT EDR 3Mbps Feature Disable.

Note

• Bit 3-7 are reserved

• 3Mbps Disable means using 2Mbps DataRate

SL_SI91X_BT_EDR_2MBPS_DISABLE#

#define SL_SI91X_BT_EDR_2MBPS_DISABLE

BIT(9)

BT EDR 2Mbps Feature Disable.

Note

• 2Mbps Disable means using 3Mbps DataRate

SL_SI91X_BT_5_SLOT_PACKETS_DISABLE#

#define SL_SI91X_BT_5_SLOT_PACKETS_DISABLE

BIT(10)

BT 5 Slot Packet Feature Disable.

SL_SI91X_BT_3_SLOT_PACKETS_DISABLE#

#define SL_SI91X_BT_3_SLOT_PACKETS_DISABLE

BIT(11)

BT 3 Slot Packet Feature Disable.

SL_SI91X_TA_BASED_ENCODER_ENABLE#

#define SL_SI91X_TA_BASED_ENCODER_ENABLE

BIT(14)

TA based encoder.

Note

• Bits 12-13 bit are reserved

• To Enable/Disable SBC Encoder in Firmware.This feature is not supported in the current release

SL_SI91X_HFP_PROFILE_ENABLE#

#define SL_SI91X_HFP_PROFILE_ENABLE

BIT(15)

To enable HFP profile.

Note

• This feature is not supported in the current release

SL_SI91X_A2DP_PROFILE_ENABLE#

#define SL_SI91X_A2DP_PROFILE_ENABLE

BIT(23)

To enable A2DP profile.

Note

• Bits 16 - 22 are reserved

SL_SI91X_A2DP_SOURCE_ROLE_ENABLE#

#define SL_SI91X_A2DP_SOURCE_ROLE_ENABLE

BIT(24)

To enable A2DP Profile role as source/sink.

SL_SI91X_A2DP_ACCELERATOR_MODE_ENABLE#

#define SL_SI91X_A2DP_ACCELERATOR_MODE_ENABLE

BIT(25)

To enable A2DP Accelerator mode.

Note

• This feature is not supported in the current release

SL_SI91X_BT_BLE_CP_BUFF_SIZE#

#define SL_SI91X_BT_BLE_CP_BUFF_SIZE

BIT(27)

To enable Buffer Alignment for Test Mode.

Note

• Bit 26 is reserved

• To get 512 bytes from common pool, need to enable this, else 320 bytes will be fixed

SL_SI91X_BT_ATT_OVER_CLASSIC_ACL#

#define SL_SI91X_BT_ATT_OVER_CLASSIC_ACL

BIT(29)

Note

• Bit 28 is reserved

SL_SI91X_BT_RF_TYPE#

#define SL_SI91X_BT_RF_TYPE

BIT(30)

To bt rf type.

SL_SI91X_ENABLE_BLE_PROTOCOL#

#define SL_SI91X_ENABLE_BLE_PROTOCOL

BIT(31)

To enable ble protocol.