WF200 Registers

This section describes the registers exposed by WFx to the host. The section focuses on the registers involved in the WF200 FMAC driver. Those registers can be accessed both using SPI or SDIO using the two modes described in Host Interface (HIF) .

1. Address Map

Name SPI Address SDIO Address Description
Config 0x00 0x00 Configuration register
Control 0x01 0x04 Control register
Direct Mode Address 0x02 0x08 Shared RAM memory address offset
Shared RAM data port 0x05 0x14 Direct Shrared RAM port access

2. CONFIG Register

Name Size (bits) SPI address SDIO address
CONFIG 32 0x00 0x00
Bit Reset Read/Write description
31-24 0x1 R Device identification information
23-20 Reserved
19 0x0 R/W SPI: Unused
SDIO: Disable CRC check on data.
-0: Normal CRC check behaviour.
-1: Disable CRC check on data transfers (CRC result assumed always correct).
18 0x0 R/W SPI: Dout_posedge_enable (1: enable, 0: disable).
SDIO: Dout_posedge_enable (1: enable, 0: disable). This is intended to be used with 50MHz SDIO clock speed.
17:16 0x0 R/W 00: both irq’s disabled
01: data irq enable
10: wlan rdy irq enable
11: both irq’s enabled
15 0x0 R/W SPI: 0 (normal functional mode)
SDIO: Disable DAT1 interrupt mechanism
-0: Normal DAT1 interrupt behaviour.
-1: Disable DAT1 interrupts. Interrupt to host are still available on WIRQ pin.
14 0x1 R/W Cpu_reset (1: cpu reset, 0: cpu non_reset)
13 0x0 R/W Direct_pre_fetch Shared RAM (1: busy, 0: data ready)
12 0x1 R/W Cpu_clk_disable (1: disable clk, 0: enable clk)
11 0x0 R/W Reserved
10 0x1 R/W Direct_access_mode (0: queue mode, 1: direct access mode)
9:8 0x0
0x2
R/W
R
Mode0 (“00”) : 4 bytes are sent : B1,B0,B3,B2
Mode1 (“01”) : 4 bytes are sent : B3,B2,B1,B0 This only make sense if the HOST works in 32-bit mode (SW-controlled)
Mode2 (“10”) : 4 bytes are sent : B0,B1,B2,B3
Note: In SPI, the config register access will always be in word_mode 0, regardless of the real value of word mode.
7 0x0
0x0
R/W
R
SPI: chip select framing disable (1: spi_cs is not checked, 0: spi_cs is checked)
SDIO: Err 7 (1: host misses CRC error, 0: no error)
6 0x0 R Err 6 (1: host tries to send data with no hif input queue entry programmed, 0: no error)
5 0x0 R Err 5 (1: host tries to send data larger than hif input buffer, 0: no error)
4 0x0 R Err 4 (1: host tries to send data when hif buffers overrun, 0: no error)
3 0x0 R Err 3 (1: host tries to read data with no hif output queue entry programmed, 0: no error)
2 0x0 R Err 2 (1: host tries to read data less than output message length, 0: no error)
1 0x0 R Err 1 (1: host tries to read data when hif buffers underrun, 0: no error)
0 0x0
0x0
R
R
SPI: Err 0 (1: CSN Framing error ,0: no error)
SDIO: Err 0 (1: Buffer number mismatch, 0: no error)

3. CONTROL Register

Name Size (bits) SPI Address SDIO Address
CONTROL 16 0x01 0x4
Bit Reset Read/Write description
15:14 0x0 R Frame type information:
00: Confirmation message
01: Indication message
10: Management message
11: Ethernet data packet
13 0x0 R Wlan_rdy (1: wlan is ready, 0: wlan not ready)
12 0x0 R/W Wlan_wup (1: prevent to go to sleep, 0: allow to go to sleep)
11:0 0x0 R Next output Queue item length

4. Card Common Control Register (SDIO specific)

Name Size (Bytes) Address
CCCR 256 0x00000
Offset Reset Read/Write description
0x00 0x11 R/O CCCR/SDIO Revision
0x01 0x0 R/O SD Specification Revision
0x02 0x0 R/W I/O Function Enable
0x03 0x0 R/O I/O Function Ready
0x04 0x0 R/W Interrupt Enable (7 functions and 1 master)
0x05 0x0 R/O Interrupt Pending for each function
0x06 0x0 W/O I/O Function Abort
0x07 0x0 R/W* Bus Interface Control
0x08 0x1F R/W* Card Capability
0x09-0x0B 0x1000 R/O Common CIS Pointer
0x0C 0x0 R/W* Bus Suspend
0x0D 0x0 R/W* Function Select
0x0E 0x0 R/O Function Execution Flags
0x0F 0x0 R/O Function Ready Flags
0x10-0x11 0x0 R/W Function0 Block Size
0x12 0x0 R/W* Power Control
0x13-0xEF unused – Reserved for Future Use
0xF0-0xFF unused – Reserved for Vendors

R/W*: There are also R/O bits

5. Function Basic Registers (FBR) of Function1 (SDIO specific)

Register Name Size (Bytes) Address
FBR 256 0x00100
Offset Reset Read/Write description
0x00 0x0 R/O Function1 Standard SDIO Function Interface Code
0x01 0x0 R/O Function1 Standard SDIO Function Interface Code
0x02 0x0 R/W* Power Selection
0x03-0x08 Reserved
0x09-0x0B 0x2000 R/O Pointer to Function1 Card Information Pointer (CIS)
0x0C-0x0E 0x0 R/O Pointer to Function1 Code Storage Area (CSA)
0x0F 0x0 R/O Data Access Window to CSA
0x10-0x11 0x0 R/W Function1 Block Size
0x12-0xFF Reserved

R/W*: There are also R/O bits