I2CSPMKit Drivers

Data Structures

struct I2CSPM_Init_TypeDef

Macros

#define I2CSPM_INIT_DEFAULT

Functions

void I2CSPM_Init ( I2CSPM_Init_TypeDef *init)
Initalize I2C peripheral.
I2C_TransferReturn_TypeDef I2CSPM_Transfer ( I2C_TypeDef *i2c, I2C_TransferSeq_TypeDef *seq)
Perform I2C transfer.

Macro Definition Documentation

#define I2CSPM_INIT_DEFAULT
Value:
{ I2C0 , /* Use I2C instance 0 */ \
gpioPortC, /* SCL port */ \
5, /* SCL pin */ \
gpioPortC, /* SDA port */ \
4, /* SDA pin */ \
0, /* Location */ \
0, /* Use currently configured reference clock */ \
I2C_FREQ_STANDARD_MAX, /* Set to standard rate */ \
i2cClockHLRStandard, /* Set to use 4:4 low/high duty cycle */ \
}
I2C0
#define I2C0
Definition: efr32fg14p232f256gm48.h:418

Default config for I2C init structure. The default may be overridden by a i2cspmconfig.h file.

Definition at line 75 of file i2cspm.h .

Referenced by BOARD_init() .

Function Documentation

void I2CSPM_Init ( I2CSPM_Init_TypeDef * init )

Initalize I2C peripheral.

This driver supports master mode only, single bus-master. In addition to configuring the I2C peripheral module, it also configures DK/STK specific setup in order to use the I2C bus.

Parameters
[in] init Pointer to I2C initialization structure

Definition at line 43 of file i2cspm.c .

References _I2C_ROUTELOC0_SCLLOC_SHIFT , _I2C_ROUTELOC0_SDALOC_SHIFT , I2C_Init_TypeDef::clhr , CMU_ClockEnable() , cmuClock_HFPER , cmuClock_I2C0 , I2C_Init_TypeDef::enable , I2C_Init_TypeDef::freq , GPIO_PinModeSet() , GPIO_PinOutClear() , GPIO_PinOutSet() , gpioModeWiredAndPullUp , I2C0 , I2C_Init() , I2C_ROUTEPEN_SCLPEN , I2C_ROUTEPEN_SDAPEN , I2CSPM_Init_TypeDef::i2cClhr , I2CSPM_Init_TypeDef::i2cMaxFreq , I2CSPM_Init_TypeDef::i2cRefFreq , I2C_Init_TypeDef::master , I2CSPM_Init_TypeDef::port , I2CSPM_Init_TypeDef::portLocationScl , I2CSPM_Init_TypeDef::portLocationSda , I2C_Init_TypeDef::refFreq , I2C_TypeDef::ROUTELOC0 , I2C_TypeDef::ROUTEPEN , I2CSPM_Init_TypeDef::sclPin , I2CSPM_Init_TypeDef::sclPort , I2CSPM_Init_TypeDef::sdaPin , and I2CSPM_Init_TypeDef::sdaPort .

Referenced by BOARD_init() , and BSP_initBoard() .

I2C_TransferReturn_TypeDef I2CSPM_Transfer ( I2C_TypeDef * i2c,
I2C_TransferSeq_TypeDef * seq
)

Perform I2C transfer.

This driver only supports master mode, single bus-master. It does not return until the transfer is complete, polling for completion.

Parameters
[in] i2c Pointer to the peripheral port
[in] seq Pointer to sequence structure defining the I2C transfer to take place. The referenced structure must exist until the transfer has fully completed.

Definition at line 123 of file i2cspm.c .

References I2C_Transfer() , I2C_TransferInit() , and i2cTransferInProgress .

Referenced by CCS811_getMeasurement() , CCS811_getRawData() , CCS811_readMailbox() , CCS811_setEnvData() , CCS811_setMeasureMode() , CCS811_softwareReset() , EEPROM_AckPoll() , EEPROM_Read() , EEPROM_Write() , SI1133_registerBlockRead() , SI1133_registerBlockWrite() , SI1133_registerRead() , SI1133_registerWrite() , Si1147_Read_Block_Register() , Si1147_Read_Register() , Si1147_Write_Block_Register() , Si1147_Write_Register() , Si7013_Detect() , Si7013_GetFirmwareRevision() , SI7021_cmdRead() , SI7021_cmdWrite() , SI7210_registerRead() , SI7210_registerWrite() , SI7210_wakeUp() , Si72xx_Read_Register() , Si72xx_WakeUpAndIdle() , Si72xx_Write_Register() , TEMPSENS_RegisterGet() , and TEMPSENS_RegisterSet() .