Plugin Commands: ZigBee 3.0 Test Harness#

Disable the printing of APS commands.

Enable the printing of APS commands.

Disable the printing of beacon requests and received beacons.

Enable the printing of beacon requests and received beacons.

Disable the printing of network commands.

Enable the printing of network commands.

Disable the printing of raw MAC commands.

Enable the printing of raw MAC commands.

Disable the printing of ZDO commands.

Enable the printing of ZDO commands.

Send an APS remove device command.

• parentLongAddress - OCTET_STRING - The long address of the parent whose child will be removed.

• destinationLongAddress - OCTET_STRING - The long address of the node which will be removed.

• options - INT32U - The negative behavior options for this command.

Configures the APS remove device command handling.

• options - INT32U - The negative behavior options for this command.

Send an APS request key command.

• destination - INT16U - The short address destination of the command.

• keyType - INT8U - The key type in the command payload.

• partnerAddress - OCTET_STRING - The partner address for the requested link key.

• options - INT32U - The negative behavior options for this command.

Send a beacon request.

Send a beacon.

• options - INT32U - The negative behavior options for this command.

Clear the install code from the device.

Clear the install code from the device.

• installCode - OCTET_STRING - The install code for this device to use.

Disable using the legacy profile of 0xC05E for ZLL commands.

Enable using the legacy profile of 0xC05E for ZLL commands.

Unicast a permit joining command.

• destination - INT16U - The destination address of the command.

• removeChildren - BOOLEAN - Whether or not the leaving device should remove its children.

• rejoin - BOOLEAN - Whether or not the destination node should rejoin the network.

• options - INT32U - The negative behavior options for this command.

Unicast a network update command.

• scanChannel - INT16U - The scan channel for the command.

• scanDuration - INT16U - The scan duration for the command.

• scanCount - INT8U - The scan count for the command.

• destination - INT16U - The scan destination.

• options - INT32U - The negative behavior options for this command.

Unicast a permit joining command.

• permitDurationS - INT16U - The permit duration, in seconds.

• destination - INT16U - The destination address of the command.

• options - INT32U - The negative behavior options for this command.

Get the current network update id.

Configure the next outgoing IEEE address request.

Configure the next outgoing IEEE address request.

Configure the next outgoing IEEE address request.

Do not supress network leave commands.

Supress network leave commands.

Send a Network Leave command.

• rejoin - BOOLEAN - Whether or not the device should rejoin.

• request - BOOLEAN - Whether or not this command is a request.

• removeChildren - BOOLEAN - Whether or not the leaving device should remove its children.

• destination - INT16U - The destination address of the command.

• options - INT32U - The negative behavior options for this command.

Do not supress network leave commands.

Supress network leave commands.

Send a Rejoin Request command.

• destination - INT16U - The destination address of the command.

Send a Rejoin Response command.

• newAddress - INT16U - The new short address of the destination node.

• status - INT8U - The status of the rejoin.

• destination - INT16U - The destination address of the command.

Set the network update id in the current network parameters block.

• updateId - INT8U - The new network update id.

Configuration command to set up OTA server.

• shortAddress - INT16U - Short Address

• destinationEndpoint - INT8U - Destination Endpoint

• manufacturerCode - INT16U - Manufacturer Code.

• imageType - INT16U - Image Type.

• fileVersion - INT32U - File Version

• fileSize - INT32U - File Size

Configuration command to set up OTA server.

Print the platform information for this device.

Resets the device to a factory new state (empty tables, attributes at default values, no events queued etc) without resetting the any of the physical hardware that could cause the device to not operate on the same serial connection.

Set the node ID to be used on the device.

• mode - INT8U - The device mode.

Set the PAN ID to be used by the Network Creator plugin.

• panId - INT16U - The PAN ID for the Network Creator plugin to use.

Set the node ID to be used on the device.

• nodeId - INT16U - The node ID to use as this device's short ID.

Send an device information request to the target found in the scan request process.

• startIndex - INT8U - The start index in the device information request command

• options - INT32U - The negative behavior options for this command.

Send an device information request to the target specefied with the short address in the command.

• startIndex - INT8U - The start index in the device information request command

• shortAddress - INT16U - The short address of the target

• options - INT32U - The negative behavior options for this command.

Configure the next device information response.

• options - INT32U - The negative behavior options for this command.

Send a get endpoint list request.

• startIndex - INT8U - The start index in the command payload.

Send a get group identifiers request.

• startIndex - INT8U - The start index in the command payload.

Send an identify request to the target found in the scan request process.

• duration - INT16U - The duration length of the identify state.

• options - INT32U - The negative behavior options for this command.

Print out whether or not the device is currently performing the scan process for touchlinking.

Send a network end device join request to the target found in the scan request process.

• networkAddress - INT16U - The designated node ID for the target node.

• freeAddrBegin - INT16U - The free address range begin.

• freeAddrEnd - INT16U - The free address range end.

• freeGroupBegin - INT16U - The free group range begin.

• freeGroupEnd - INT16U - The free group range end.

• options - INT32U - The negative behavior options for this command.

Send a network router join request to the target found in the scan request process.

• networkAddress - INT16U - The designated node ID for the target node.

• freeAddrBegin - INT16U - The free address range begin.

• freeAddrEnd - INT16U - The free address range end.

• freeGroupBegin - INT16U - The free group range begin.

• freeGroupEnd - INT16U - The free group range end.

• options - INT32U - The negative behavior options for this command.

Configure the next outgoing network join router response command.

• options - INT32U - The negative behavior options for this command.

Send a network start request to the target found in the scan request process.

• networkAddress - INT16U - The designated node ID for the target node.

• freeAddrBegin - INT16U - The free address range begin.

• freeAddrEnd - INT16U - The free address range end.

• freeGroupBegin - INT16U - The free group range begin.

• freeGroupEnd - INT16U - The free group range end.

• options - INT32U - The negative behavior options for this command.

Configure the next outgoing network start response command.

• options - INT32U - The negative behavior options for this command.

Send a network update request.

• options - INT32U - The negative behavior options for this command.

Send a reset to factory new request to the target found in the scan request process.

• options - INT32U - The negative behavior options for this command.

Start the scan request process.

• linkInitiator - INT8U - The link initiator bit in scan requests.

• unused - INT16U - This argument is unsed.

• options - INT32U - The negative behavior options for this command.

Configure the next scan response.

• options - INT32U - The negative behavior options for this command.

Start a distributed network on which to perform ZLL operations.

• panId - INT16U - The PAN ID that will be used.

• options - INT32U - The negative behavior options for this command.

Send a ZCL ReadAttribute command.

• clusterId - INT16U - The cluster ID in the command.

• attributeId - INT16U - The attribute ID in the command.

• destination - INT16U - The destination of the command.

• srcEndpoint - INT8U - The source endpoint of the command.

• dstEndpoint - INT8U - The destination endpoint of the command.

• profileId - INT16U - The profile ID in the command.

Unicast an active endpoint request.

• destination - INT16U - The destination address of the command.

• networkAddressOfInterest - INT16U - The network address of interest.

• options - INT32U - The negative behavior options for this command.

Rebroadcast a "fake" ZDO device announce. The device sets random frame counter values to appear as though the DeviceAnnounce has been rebroadcasted from another device on the network out of range of the DUT.

• shortAddress - INT16U - Short address of the fake device announce

• ieeeAddress - IEEE_ADDRESS - IEEE address of the fake device announce

Send a ZDO Bind command to a device specified in the command arguments.

• destination - INT16U - Two byte destination node id

• source Endpoint - INT8U - Remote device's source endpoint to bind

• destEndpoint - INT8U - Remote endpoint to bind

• cluster - INT16U - Cluster on which to bind

• remoteEUI64 - IEEE_ADDRESS - Remote node EUI64

• destEUI64 - IEEE_ADDRESS - Binding's dest EUI64. Usually the local node's EUI64

Send a ZDO bind command to a device specified to create a groupcast binding.

• shortAddress - INT16U - The destination of the ZDO command

• sourceEndpoint - INT8U - Remote device's source endpoint to bind

• destEndpoint - INT8U - Remote endpoint to bind

• destination - INT16U - Two byte destination address for the binding

• cluster - INT16U - Cluster on which to bind

• srcAddress - IEEE_ADDRESS - The source IEEE address for the binding

Send an IEEE address request.

• addrOfInterest - INT16U - The short address of interest

• type - INT8U - The request type.

• startIndex - INT8U - The start index for the requested elements of the associated devices list if the type of this command is Extended response.

• destination - INT16U - The destination address of the command.

• options - INT32U - The negative behavior options for this command.

Add clusters to the known server (in) clusters on this device.

• clusterId - INT16U - Server cluster id

Clear the ZDO list of server (in) clusters.

Send a ZDO Management Leave command to the target device.

• target - INT16U - Target node ID

• removeChildren - BOOLEAN - Remove children

• rejoin - BOOLEAN - Rejoin after leave

Unicast a match descriptor request.

• destination - INT16U - The destination address of the command.

• networkAddressOfInterest - INT16U - The network address of interest.

• profileId - INT16U - The profile id in the APS header of the command.

• options - INT32U - The negative behavior options for this command.

Configure the next outgoing match descriptor response.

• networkAddressOfInterest - INT16U - The network address of interest.

• status - INT8U - The status for the response command.

• options - INT32U - The negative behavior options for this command.

Send a ZDO MGMT-Bind (Binding Table) Request to the target device.

• target - INT16U - Target node ID

• startIndex - INT8U - Starting index into table query

Send a ZDO MGMT-LQI (LQI Table) Request to the target device.

• target - INT16U - Target node ID

• startIndex - INT8U - Starting index into table query

Sends a node descriptor request to a given target device

• target - INT16U - Two byte address for the target device.

Unicast a node descriptor request.

• destination - INT16U - The destination address of the command.

Send a ZDO address request.

• ieeeAddress - IEEE_ADDRESS - The long address of the destination.

• type - INT8U - The type of the rejoin request.

• startIndex - INT8U - The start index for the requested elements of the associated devices list if the type of this command is Extended response.

• destination - INT16U - The destination address of the command.

• options - INT32U - The negative behavior options for this command.

Add clusters to the known client (out) clusters on this device.

• clusterId - INT16U - Client cluster ids

Clear the ZDO list of client (out) clusters.

Send a ZDO Power Descriptor Request to the target device.

• target - INT16U - Target node ID

Send a ZDO route request command to the target.

• target - INT16U - Target node ID

• index - INT8U - The index of the remote node's routing table to request.

Unicast a simple descriptor request.

• destination - INT16U - The destination address of the command.

• endpoint - INT8U - The endpoint for the simple descriptor request.

• networkAddressOfInterest - INT16U - The network address of interest.

• options - INT32U - The negative behavior options for this command.

Configure the next outgoing simple descriptor response.

• networkAddressOfInterest - INT16U - The network address of interest.

• status - INT8U - The status for the response command.

• length - INT8U - The trimmed length of the command.

• options - INT32U - The negative behavior options for this command.

Sends an unbind request for a multicast binding to the target device.

• target - INT16U - Target node ID

• source eui64 - IEEE_ADDRESS - The source EUI64 of the binding (the remote device's EUI64)

• source endpoint - INT8U - The source endpoint of the binding.

• clusterID - INT16U - The cluster ID to unbind.

• groupAddress - INT16U - The group address in the binding

Sends an unbind request for a unicast binding to the target device.

• target - INT16U - Target node ID

• source eui64 - IEEE_ADDRESS - The source EUI64 of the binding (the remote device's EUI64)

• source endpoint - INT8U - The source endpoint of the binding.

• clusterID - INT16U - The cluster ID to unbind.

• destinationEUI64 - IEEE_ADDRESS - The destination EUI64 in the binding (usually the local node's EUI64

• destEndpoint - INT8U - The destination endpoint of the binding

Configure the next outgoing node descriptor response.

• options - INT32U - The negative behavior options for this command.

Reset any pending negative ZDO behavior.