Plugin Commands: ZigBee 3.0 Test Harness#
The test harness commands are used to test various unusual functionality or behavior of a remote device.
Macros#
plugin test-harness packet-printing aps-printing disable
plugin test-harness packet-printing aps-printing enable
plugin test-harness packet-printing beacon-printing disable
plugin test-harness packet-printing beacon-printing enable
plugin test-harness packet-printing nwk-printing disable
plugin test-harness packet-printing nwk-printing enable
plugin test-harness packet-printing raw-printing disable
plugin test-harness packet-printing raw-printing enable
plugin test-harness packet-printing zdo-printing disable
plugin test-harness packet-printing zdo-printing enable
plugin test-harness z3 aps aps-remove-device [parentLongAddress:-1] [destinationLongAddress:-1] [options:4]
plugin test-harness z3 aps aps-remove-device-config [options:4]
plugin test-harness z3 aps aps-request-key [destination:2] [keyType:1] [partnerAddress:-1] [options:4]
plugin test-harness z3 beacon beacon-req
plugin test-harness z3 beacon beacons-config [options:4]
plugin test-harness z3 install-code clear
plugin test-harness z3 install-code set [installCode:-1]
plugin test-harness z3 legacy-profile disable
plugin test-harness z3 legacy-profile enable
plugin test-harness z3 mgmt leave [destination:2] [removeChildren:1] [rejoin:1] [options:4]
plugin test-harness z3 mgmt nwk-update-request [scanChannel:2] [scanDuration:2] [scanCount:1] [destination:2] [options:4]
plugin test-harness z3 mgmt permit-joining-req [permitDurationS:2] [destination:2] [options:4]
plugin test-harness z3 nwk get-network-update-id
plugin test-harness z3 nwk ieee-addr-rsp-config issuer-nwk-address-remote-dev
plugin test-harness z3 nwk ieee-addr-rsp-config reset
plugin test-harness z3 nwk ieee-addr-rsp-config status-device-not-found
plugin test-harness z3 nwk nwk-key-supression off
plugin test-harness z3 nwk nwk-key-supression on
plugin test-harness z3 nwk nwk-leave [rejoin:1] [request:1] [removeChildren:1] [destination:2] [options:4]
plugin test-harness z3 nwk nwk-leave-supression off
plugin test-harness z3 nwk nwk-leave-supression on
plugin test-harness z3 nwk nwk-rejoin-request [destination:2]
plugin test-harness z3 nwk nwk-rejoin-response [newAddress:2] [status:1] [destination:2]
plugin test-harness z3 nwk set-network-update-id [updateId:1]
plugin test-harness z3 ota-server activate [shortAddress:2] [destinationEndpoint:1] [manufacturerCode:2] [imageType:2] [fileVersion:4] [fileSize:4]
plugin test-harness z3 ota-server deactivate
plugin test-harness z3 platform
plugin test-harness z3 reset
plugin test-harness z3 set-device-mode [mode:1]
plugin test-harness z3 set-pan-id [panId:2]
plugin test-harness z3 set-short-address [nodeId:2]
plugin test-harness z3 touchlink device-information-request [startIndex:1] [options:4]
plugin test-harness z3 touchlink device-information-request-w-target [startIndex:1] [shortAddress:2] [options:4]
plugin test-harness z3 touchlink device-information-response-config [options:4]
plugin test-harness z3 touchlink get-endpoint-list-request [startIndex:1]
plugin test-harness z3 touchlink get-group-identifiers-request [startIndex:1]
plugin test-harness z3 touchlink identify-request [duration:2] [options:4]
plugin test-harness z3 touchlink is-scanning
plugin test-harness z3 touchlink network-join-end-device-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
plugin test-harness z3 touchlink network-join-router-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
plugin test-harness z3 touchlink network-join-router-response-config [options:4]
plugin test-harness z3 touchlink network-start-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
plugin test-harness z3 touchlink network-start-response-config [options:4]
plugin test-harness z3 touchlink network-update-request [options:4]
plugin test-harness z3 touchlink reset-to-factory-new-request [options:4]
plugin test-harness z3 touchlink scan-request-process [linkInitiator:1] [unused:2] [options:4]
plugin test-harness z3 touchlink scan-response-config [options:4]
plugin test-harness z3 touchlink start-as-router [panId:2] [options:4]
plugin test-harness z3 zcl read [clusterId:2] [attributeId:2] [destination:2] [srcEndpoint:1] [dstEndpoint:1] [profileId:2]
plugin test-harness z3 zdo active-endpoint-request [destination:2] [networkAddressOfInterest:2] [options:4]
plugin test-harness z3 zdo bc-device-announce [shortAddress:2] [ieeeAddress:8]
plugin test-harness z3 zdo bind [destination:2] [source Endpoint:1] [destEndpoint:1] [cluster:2] [remoteEUI64:8] [destEUI64:8]
plugin test-harness z3 zdo bind-group [shortAddress:2] [sourceEndpoint:1] [destEndpoint:1] [destination:2] [cluster:2] [srcAddress:8]
plugin test-harness z3 zdo ieee-addr-req [addrOfInterest:2] [type:1] [startIndex:1] [destination:2] [options:4]
plugin test-harness z3 zdo in-cl-list add [clusterId:2]
plugin test-harness z3 zdo in-cl-list clear
plugin test-harness z3 zdo leave [target:2] [removeChildren:1] [rejoin:1]
plugin test-harness z3 zdo match-desc-req [destination:2] [networkAddressOfInterest:2] [profileId:2] [options:4]
plugin test-harness z3 zdo match-desc-rsp-config [networkAddressOfInterest:2] [status:1] [options:4]
plugin test-harness z3 zdo mgmt-bind [target:2] [startIndex:1]
plugin test-harness z3 zdo mgmt-lqi [target:2] [startIndex:1]
plugin test-harness z3 zdo node [target:2]
plugin test-harness z3 zdo node-desc-req [destination:2]
plugin test-harness z3 zdo nwk-addr-req [ieeeAddress:8] [type:1] [startIndex:1] [destination:2] [options:4]
plugin test-harness z3 zdo out-cl-list add [clusterId:2]
plugin test-harness z3 zdo out-cl-list clear
plugin test-harness z3 zdo power [target:2]
plugin test-harness z3 zdo route [target:2] [index:1]
plugin test-harness z3 zdo simple-desc-req [destination:2] [endpoint:1] [networkAddressOfInterest:2] [options:4]
plugin test-harness z3 zdo simple-desc-rsp-config [networkAddressOfInterest:2] [status:1] [length:1] [options:4]
plugin test-harness z3 zdo unbind group [target:2] [source eui64:8] [source endpoint:1] [clusterID:2] [groupAddress:2]
plugin test-harness z3 zdo unbind unicast [target:2] [source eui64:8] [source endpoint:1] [clusterID:2] [destinationEUI64:8] [destEndpoint:1]
plugin test-harness z3 zdo zdo-node-desc-rsp-config [options:4]
plugin test-harness z3 zdo zdo-reset
Macro Definition Documentation#
EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_APS_PRINTING_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_APS_PRINTING_DISABLE
plugin test-harness packet-printing aps-printing disable
Disable the printing of APS commands.
7251 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_APS_PRINTING_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_APS_PRINTING_ENABLE
plugin test-harness packet-printing aps-printing enable
Enable the printing of APS commands.
7256 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_BEACON_PRINTING_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_BEACON_PRINTING_DISABLE
plugin test-harness packet-printing beacon-printing disable
Disable the printing of beacon requests and received beacons.
7261 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_BEACON_PRINTING_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_BEACON_PRINTING_ENABLE
plugin test-harness packet-printing beacon-printing enable
Enable the printing of beacon requests and received beacons.
7266 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_NWK_PRINTING_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_NWK_PRINTING_DISABLE
plugin test-harness packet-printing nwk-printing disable
Disable the printing of network commands.
7271 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_NWK_PRINTING_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_NWK_PRINTING_ENABLE
plugin test-harness packet-printing nwk-printing enable
Enable the printing of network commands.
7276 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_RAW_PRINTING_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_RAW_PRINTING_DISABLE
plugin test-harness packet-printing raw-printing disable
Disable the printing of raw MAC commands.
7281 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_RAW_PRINTING_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_RAW_PRINTING_ENABLE
plugin test-harness packet-printing raw-printing enable
Enable the printing of raw MAC commands.
7286 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_ZDO_PRINTING_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_ZDO_PRINTING_DISABLE
plugin test-harness packet-printing zdo-printing disable
Disable the printing of ZDO commands.
7291 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_ZDO_PRINTING_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_PACKET_PRINTING_ZDO_PRINTING_ENABLE
plugin test-harness packet-printing zdo-printing enable
Enable the printing of ZDO commands.
7296 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REMOVE_DEVICE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REMOVE_DEVICE
plugin test-harness z3 aps aps-remove-device [parentLongAddress:-1] [destinationLongAddress:-1] [options:4]
Send an APS remove device command.
parentLongAddress - OCTET_STRING - The long address of the parent whose child will be removed.
destinationLongAddress - OCTET_STRING - The long address of the node which will be removed.
options - INT32U - The negative behavior options for this command.
7304 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REMOVE_DEVICE_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REMOVE_DEVICE_CONFIG
plugin test-harness z3 aps aps-remove-device-config [options:4]
Configures the APS remove device command handling.
options - INT32U - The negative behavior options for this command.
7310 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REQUEST_KEY#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_APS_APS_REQUEST_KEY
plugin test-harness z3 aps aps-request-key [destination:2] [keyType:1] [partnerAddress:-1] [options:4]
Send an APS request key command.
destination - INT16U - The short address destination of the command.
keyType - INT8U - The key type in the command payload.
partnerAddress - OCTET_STRING - The partner address for the requested link key.
options - INT32U - The negative behavior options for this command.
7319 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_BEACON_BEACON_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_BEACON_BEACON_REQ
plugin test-harness z3 beacon beacon-req
Send a beacon request.
7324 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_BEACON_BEACONS_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_BEACON_BEACONS_CONFIG
plugin test-harness z3 beacon beacons-config [options:4]
Send a beacon.
options - INT32U - The negative behavior options for this command.
7330 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_INSTALL_CODE_CLEAR#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_INSTALL_CODE_CLEAR
plugin test-harness z3 install-code clear
Clear the install code from the device.
7335 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_INSTALL_CODE_SET#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_INSTALL_CODE_SET
plugin test-harness z3 install-code set [installCode:-1]
Clear the install code from the device.
installCode - OCTET_STRING - The install code for this device to use.
7341 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_LEGACY_PROFILE_DISABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_LEGACY_PROFILE_DISABLE
plugin test-harness z3 legacy-profile disable
Disable using the legacy profile of 0xC05E for ZLL commands.
7346 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_LEGACY_PROFILE_ENABLE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_LEGACY_PROFILE_ENABLE
plugin test-harness z3 legacy-profile enable
Enable using the legacy profile of 0xC05E for ZLL commands.
7351 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_LEAVE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_LEAVE
plugin test-harness z3 mgmt leave [destination:2] [removeChildren:1] [rejoin:1] [options:4]
Unicast a permit joining command.
destination - INT16U - The destination address of the command.
removeChildren - BOOLEAN - Whether or not the leaving device should remove its children.
rejoin - BOOLEAN - Whether or not the destination node should rejoin the network.
options - INT32U - The negative behavior options for this command.
7360 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_NWK_UPDATE_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_NWK_UPDATE_REQUEST
plugin test-harness z3 mgmt nwk-update-request [scanChannel:2] [scanDuration:2] [scanCount:1] [destination:2] [options:4]
Unicast a network update command.
scanChannel - INT16U - The scan channel for the command.
scanDuration - INT16U - The scan duration for the command.
scanCount - INT8U - The scan count for the command.
destination - INT16U - The scan destination.
options - INT32U - The negative behavior options for this command.
7370 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_PERMIT_JOINING_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_MGMT_PERMIT_JOINING_REQ
plugin test-harness z3 mgmt permit-joining-req [permitDurationS:2] [destination:2] [options:4]
Unicast a permit joining command.
permitDurationS - INT16U - The permit duration, in seconds.
destination - INT16U - The destination address of the command.
options - INT32U - The negative behavior options for this command.
7378 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_GET_NETWORK_UPDATE_ID#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_GET_NETWORK_UPDATE_ID
plugin test-harness z3 nwk get-network-update-id
Get the current network update id.
7383 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_ISSUER_NWK_ADDRESS_REMOTE_DEV#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_ISSUER_NWK_ADDRESS_REMOTE_DEV
plugin test-harness z3 nwk ieee-addr-rsp-config issuer-nwk-address-remote-dev
Configure the next outgoing IEEE address request.
7388 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_RESET#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_RESET
plugin test-harness z3 nwk ieee-addr-rsp-config reset
Configure the next outgoing IEEE address request.
7393 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_STATUS_DEVICE_NOT_FOUND#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_IEEE_ADDR_RSP_CONFIG_STATUS_DEVICE_NOT_FOUND
plugin test-harness z3 nwk ieee-addr-rsp-config status-device-not-found
Configure the next outgoing IEEE address request.
7398 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_KEY_SUPRESSION_OFF#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_KEY_SUPRESSION_OFF
plugin test-harness z3 nwk nwk-key-supression off
Do not supress network leave commands.
7403 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_KEY_SUPRESSION_ON#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_KEY_SUPRESSION_ON
plugin test-harness z3 nwk nwk-key-supression on
Supress network leave commands.
7408 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE
plugin test-harness z3 nwk nwk-leave [rejoin:1] [request:1] [removeChildren:1] [destination:2] [options:4]
Send a Network Leave command.
rejoin - BOOLEAN - Whether or not the device should rejoin.
request - BOOLEAN - Whether or not this command is a request.
removeChildren - BOOLEAN - Whether or not the leaving device should remove its children.
destination - INT16U - The destination address of the command.
options - INT32U - The negative behavior options for this command.
7418 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE_SUPRESSION_OFF#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE_SUPRESSION_OFF
plugin test-harness z3 nwk nwk-leave-supression off
Do not supress network leave commands.
7423 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE_SUPRESSION_ON#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_LEAVE_SUPRESSION_ON
plugin test-harness z3 nwk nwk-leave-supression on
Supress network leave commands.
7428 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_REJOIN_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_REJOIN_REQUEST
plugin test-harness z3 nwk nwk-rejoin-request [destination:2]
Send a Rejoin Request command.
destination - INT16U - The destination address of the command.
7434 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_REJOIN_RESPONSE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_NWK_REJOIN_RESPONSE
plugin test-harness z3 nwk nwk-rejoin-response [newAddress:2] [status:1] [destination:2]
Send a Rejoin Response command.
newAddress - INT16U - The new short address of the destination node.
status - INT8U - The status of the rejoin.
destination - INT16U - The destination address of the command.
7442 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_SET_NETWORK_UPDATE_ID#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_NWK_SET_NETWORK_UPDATE_ID
plugin test-harness z3 nwk set-network-update-id [updateId:1]
Set the network update id in the current network parameters block.
updateId - INT8U - The new network update id.
7448 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_OTA_SERVER_ACTIVATE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_OTA_SERVER_ACTIVATE
plugin test-harness z3 ota-server activate [shortAddress:2] [destinationEndpoint:1] [manufacturerCode:2] [imageType:2] [fileVersion:4] [fileSize:4]
Configuration command to set up OTA server.
shortAddress - INT16U - Short Address
destinationEndpoint - INT8U - Destination Endpoint
manufacturerCode - INT16U - Manufacturer Code.
imageType - INT16U - Image Type.
fileVersion - INT32U - File Version
fileSize - INT32U - File Size
7459 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_OTA_SERVER_DEACTIVATE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_OTA_SERVER_DEACTIVATE
plugin test-harness z3 ota-server deactivate
Configuration command to set up OTA server.
7464 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_PLATFORM#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_PLATFORM
plugin test-harness z3 platform
Print the platform information for this device.
7469 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_RESET#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_RESET
plugin test-harness z3 reset
Resets the device to a factory new state (empty tables, attributes at default values, no events queued etc) without resetting the any of the physical hardware that could cause the device to not operate on the same serial connection.
7474 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_DEVICE_MODE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_DEVICE_MODE
plugin test-harness z3 set-device-mode [mode:1]
Set the node ID to be used on the device.
mode - INT8U - The device mode.
7480 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_PAN_ID#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_PAN_ID
plugin test-harness z3 set-pan-id [panId:2]
Set the PAN ID to be used by the Network Creator plugin.
panId - INT16U - The PAN ID for the Network Creator plugin to use.
7486 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_SHORT_ADDRESS#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_SET_SHORT_ADDRESS
plugin test-harness z3 set-short-address [nodeId:2]
Set the node ID to be used on the device.
nodeId - INT16U - The node ID to use as this device's short ID.
7492 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_REQUEST
plugin test-harness z3 touchlink device-information-request [startIndex:1] [options:4]
Send an device information request to the target found in the scan request process.
startIndex - INT8U - The start index in the device information request command
options - INT32U - The negative behavior options for this command.
7499 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_REQUEST_W_TARGET#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_REQUEST_W_TARGET
plugin test-harness z3 touchlink device-information-request-w-target [startIndex:1] [shortAddress:2] [options:4]
Send an device information request to the target specefied with the short address in the command.
startIndex - INT8U - The start index in the device information request command
shortAddress - INT16U - The short address of the target
options - INT32U - The negative behavior options for this command.
7507 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_RESPONSE_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_DEVICE_INFORMATION_RESPONSE_CONFIG
plugin test-harness z3 touchlink device-information-response-config [options:4]
Configure the next device information response.
options - INT32U - The negative behavior options for this command.
7513 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_GET_ENDPOINT_LIST_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_GET_ENDPOINT_LIST_REQUEST
plugin test-harness z3 touchlink get-endpoint-list-request [startIndex:1]
Send a get endpoint list request.
startIndex - INT8U - The start index in the command payload.
7519 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_GET_GROUP_IDENTIFIERS_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_GET_GROUP_IDENTIFIERS_REQUEST
plugin test-harness z3 touchlink get-group-identifiers-request [startIndex:1]
Send a get group identifiers request.
startIndex - INT8U - The start index in the command payload.
7525 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_IDENTIFY_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_IDENTIFY_REQUEST
plugin test-harness z3 touchlink identify-request [duration:2] [options:4]
Send an identify request to the target found in the scan request process.
duration - INT16U - The duration length of the identify state.
options - INT32U - The negative behavior options for this command.
7532 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_IS_SCANNING#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_IS_SCANNING
plugin test-harness z3 touchlink is-scanning
Print out whether or not the device is currently performing the scan process for touchlinking.
7537 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_END_DEVICE_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_END_DEVICE_REQUEST
plugin test-harness z3 touchlink network-join-end-device-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
Send a network end device join request to the target found in the scan request process.
networkAddress - INT16U - The designated node ID for the target node.
freeAddrBegin - INT16U - The free address range begin.
freeAddrEnd - INT16U - The free address range end.
freeGroupBegin - INT16U - The free group range begin.
freeGroupEnd - INT16U - The free group range end.
options - INT32U - The negative behavior options for this command.
7548 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_ROUTER_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_ROUTER_REQUEST
plugin test-harness z3 touchlink network-join-router-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
Send a network router join request to the target found in the scan request process.
networkAddress - INT16U - The designated node ID for the target node.
freeAddrBegin - INT16U - The free address range begin.
freeAddrEnd - INT16U - The free address range end.
freeGroupBegin - INT16U - The free group range begin.
freeGroupEnd - INT16U - The free group range end.
options - INT32U - The negative behavior options for this command.
7559 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_ROUTER_RESPONSE_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_JOIN_ROUTER_RESPONSE_CONFIG
plugin test-harness z3 touchlink network-join-router-response-config [options:4]
Configure the next outgoing network join router response command.
options - INT32U - The negative behavior options for this command.
7565 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_START_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_START_REQUEST
plugin test-harness z3 touchlink network-start-request [networkAddress:2] [freeAddrBegin:2] [freeAddrEnd:2] [freeGroupBegin:2] [freeGroupEnd:2] [options:4]
Send a network start request to the target found in the scan request process.
networkAddress - INT16U - The designated node ID for the target node.
freeAddrBegin - INT16U - The free address range begin.
freeAddrEnd - INT16U - The free address range end.
freeGroupBegin - INT16U - The free group range begin.
freeGroupEnd - INT16U - The free group range end.
options - INT32U - The negative behavior options for this command.
7576 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_START_RESPONSE_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_START_RESPONSE_CONFIG
plugin test-harness z3 touchlink network-start-response-config [options:4]
Configure the next outgoing network start response command.
options - INT32U - The negative behavior options for this command.
7582 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_UPDATE_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_NETWORK_UPDATE_REQUEST
plugin test-harness z3 touchlink network-update-request [options:4]
Send a network update request.
options - INT32U - The negative behavior options for this command.
7588 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_RESET_TO_FACTORY_NEW_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_RESET_TO_FACTORY_NEW_REQUEST
plugin test-harness z3 touchlink reset-to-factory-new-request [options:4]
Send a reset to factory new request to the target found in the scan request process.
options - INT32U - The negative behavior options for this command.
7594 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_SCAN_REQUEST_PROCESS#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_SCAN_REQUEST_PROCESS
plugin test-harness z3 touchlink scan-request-process [linkInitiator:1] [unused:2] [options:4]
Start the scan request process.
linkInitiator - INT8U - The link initiator bit in scan requests.
unused - INT16U - This argument is unsed.
options - INT32U - The negative behavior options for this command.
7602 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_SCAN_RESPONSE_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_SCAN_RESPONSE_CONFIG
plugin test-harness z3 touchlink scan-response-config [options:4]
Configure the next scan response.
options - INT32U - The negative behavior options for this command.
7608 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_START_AS_ROUTER#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_TOUCHLINK_START_AS_ROUTER
plugin test-harness z3 touchlink start-as-router [panId:2] [options:4]
Start a distributed network on which to perform ZLL operations.
panId - INT16U - The PAN ID that will be used.
options - INT32U - The negative behavior options for this command.
7615 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZCL_READ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZCL_READ
plugin test-harness z3 zcl read [clusterId:2] [attributeId:2] [destination:2] [srcEndpoint:1] [dstEndpoint:1] [profileId:2]
Send a ZCL ReadAttribute command.
clusterId - INT16U - The cluster ID in the command.
attributeId - INT16U - The attribute ID in the command.
destination - INT16U - The destination of the command.
srcEndpoint - INT8U - The source endpoint of the command.
dstEndpoint - INT8U - The destination endpoint of the command.
profileId - INT16U - The profile ID in the command.
7626 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ACTIVE_ENDPOINT_REQUEST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ACTIVE_ENDPOINT_REQUEST
plugin test-harness z3 zdo active-endpoint-request [destination:2] [networkAddressOfInterest:2] [options:4]
Unicast an active endpoint request.
destination - INT16U - The destination address of the command.
networkAddressOfInterest - INT16U - The network address of interest.
options - INT32U - The negative behavior options for this command.
7634 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BC_DEVICE_ANNOUNCE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BC_DEVICE_ANNOUNCE
plugin test-harness z3 zdo bc-device-announce [shortAddress:2] [ieeeAddress:8]
Rebroadcast a "fake" ZDO device announce. The device sets random frame counter values to appear as though the DeviceAnnounce has been rebroadcasted from another device on the network out of range of the DUT.
shortAddress - INT16U - Short address of the fake device announce
ieeeAddress - IEEE_ADDRESS - IEEE address of the fake device announce
7641 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BIND#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BIND
plugin test-harness z3 zdo bind [destination:2] [source Endpoint:1] [destEndpoint:1] [cluster:2] [remoteEUI64:8] [destEUI64:8]
Send a ZDO Bind command to a device specified in the command arguments.
destination - INT16U - Two byte destination node id
source Endpoint - INT8U - Remote device's source endpoint to bind
destEndpoint - INT8U - Remote endpoint to bind
cluster - INT16U - Cluster on which to bind
remoteEUI64 - IEEE_ADDRESS - Remote node EUI64
destEUI64 - IEEE_ADDRESS - Binding's dest EUI64. Usually the local node's EUI64
7652 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BIND_GROUP#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_BIND_GROUP
plugin test-harness z3 zdo bind-group [shortAddress:2] [sourceEndpoint:1] [destEndpoint:1] [destination:2] [cluster:2] [srcAddress:8]
Send a ZDO bind command to a device specified to create a groupcast binding.
shortAddress - INT16U - The destination of the ZDO command
sourceEndpoint - INT8U - Remote device's source endpoint to bind
destEndpoint - INT8U - Remote endpoint to bind
destination - INT16U - Two byte destination address for the binding
cluster - INT16U - Cluster on which to bind
srcAddress - IEEE_ADDRESS - The source IEEE address for the binding
7663 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IEEE_ADDR_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IEEE_ADDR_REQ
plugin test-harness z3 zdo ieee-addr-req [addrOfInterest:2] [type:1] [startIndex:1] [destination:2] [options:4]
Send an IEEE address request.
addrOfInterest - INT16U - The short address of interest
type - INT8U - The request type.
startIndex - INT8U - The start index for the requested elements of the associated devices list if the type of this command is Extended response.
destination - INT16U - The destination address of the command.
options - INT32U - The negative behavior options for this command.
7673 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IN_CL_LIST_ADD#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IN_CL_LIST_ADD
plugin test-harness z3 zdo in-cl-list add [clusterId:2]
Add clusters to the known server (in) clusters on this device.
clusterId - INT16U - Server cluster id
7679 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IN_CL_LIST_CLEAR#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_IN_CL_LIST_CLEAR
plugin test-harness z3 zdo in-cl-list clear
Clear the ZDO list of server (in) clusters.
7684 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_LEAVE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_LEAVE
plugin test-harness z3 zdo leave [target:2] [removeChildren:1] [rejoin:1]
Send a ZDO Management Leave command to the target device.
target - INT16U - Target node ID
removeChildren - BOOLEAN - Remove children
rejoin - BOOLEAN - Rejoin after leave
7692 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MATCH_DESC_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MATCH_DESC_REQ
plugin test-harness z3 zdo match-desc-req [destination:2] [networkAddressOfInterest:2] [profileId:2] [options:4]
Unicast a match descriptor request.
destination - INT16U - The destination address of the command.
networkAddressOfInterest - INT16U - The network address of interest.
profileId - INT16U - The profile id in the APS header of the command.
options - INT32U - The negative behavior options for this command.
7701 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MATCH_DESC_RSP_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MATCH_DESC_RSP_CONFIG
plugin test-harness z3 zdo match-desc-rsp-config [networkAddressOfInterest:2] [status:1] [options:4]
Configure the next outgoing match descriptor response.
networkAddressOfInterest - INT16U - The network address of interest.
status - INT8U - The status for the response command.
options - INT32U - The negative behavior options for this command.
7709 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MGMT_BIND#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MGMT_BIND
plugin test-harness z3 zdo mgmt-bind [target:2] [startIndex:1]
Send a ZDO MGMT-Bind (Binding Table) Request to the target device.
target - INT16U - Target node ID
startIndex - INT8U - Starting index into table query
7716 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MGMT_LQI#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_MGMT_LQI
plugin test-harness z3 zdo mgmt-lqi [target:2] [startIndex:1]
Send a ZDO MGMT-LQI (LQI Table) Request to the target device.
target - INT16U - Target node ID
startIndex - INT8U - Starting index into table query
7723 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NODE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NODE
plugin test-harness z3 zdo node [target:2]
Sends a node descriptor request to a given target device
target - INT16U - Two byte address for the target device.
7729 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NODE_DESC_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NODE_DESC_REQ
plugin test-harness z3 zdo node-desc-req [destination:2]
Unicast a node descriptor request.
destination - INT16U - The destination address of the command.
7735 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NWK_ADDR_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_NWK_ADDR_REQ
plugin test-harness z3 zdo nwk-addr-req [ieeeAddress:8] [type:1] [startIndex:1] [destination:2] [options:4]
Send a ZDO address request.
ieeeAddress - IEEE_ADDRESS - The long address of the destination.
type - INT8U - The type of the rejoin request.
startIndex - INT8U - The start index for the requested elements of the associated devices list if the type of this command is Extended response.
destination - INT16U - The destination address of the command.
options - INT32U - The negative behavior options for this command.
7745 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_OUT_CL_LIST_ADD#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_OUT_CL_LIST_ADD
plugin test-harness z3 zdo out-cl-list add [clusterId:2]
Add clusters to the known client (out) clusters on this device.
clusterId - INT16U - Client cluster ids
7751 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_OUT_CL_LIST_CLEAR#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_OUT_CL_LIST_CLEAR
plugin test-harness z3 zdo out-cl-list clear
Clear the ZDO list of client (out) clusters.
7756 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_POWER#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_POWER
plugin test-harness z3 zdo power [target:2]
Send a ZDO Power Descriptor Request to the target device.
target - INT16U - Target node ID
7762 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ROUTE#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ROUTE
plugin test-harness z3 zdo route [target:2] [index:1]
Send a ZDO route request command to the target.
target - INT16U - Target node ID
index - INT8U - The index of the remote node's routing table to request.
7769 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_SIMPLE_DESC_REQ#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_SIMPLE_DESC_REQ
plugin test-harness z3 zdo simple-desc-req [destination:2] [endpoint:1] [networkAddressOfInterest:2] [options:4]
Unicast a simple descriptor request.
destination - INT16U - The destination address of the command.
endpoint - INT8U - The endpoint for the simple descriptor request.
networkAddressOfInterest - INT16U - The network address of interest.
options - INT32U - The negative behavior options for this command.
7778 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_SIMPLE_DESC_RSP_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_SIMPLE_DESC_RSP_CONFIG
plugin test-harness z3 zdo simple-desc-rsp-config [networkAddressOfInterest:2] [status:1] [length:1] [options:4]
Configure the next outgoing simple descriptor response.
networkAddressOfInterest - INT16U - The network address of interest.
status - INT8U - The status for the response command.
length - INT8U - The trimmed length of the command.
options - INT32U - The negative behavior options for this command.
7787 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_UNBIND_GROUP#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_UNBIND_GROUP
plugin test-harness z3 zdo unbind group [target:2] [source eui64:8] [source endpoint:1] [clusterID:2] [groupAddress:2]
Sends an unbind request for a multicast binding to the target device.
target - INT16U - Target node ID
source eui64 - IEEE_ADDRESS - The source EUI64 of the binding (the remote device's EUI64)
source endpoint - INT8U - The source endpoint of the binding.
clusterID - INT16U - The cluster ID to unbind.
groupAddress - INT16U - The group address in the binding
7797 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_UNBIND_UNICAST#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_UNBIND_UNICAST
plugin test-harness z3 zdo unbind unicast [target:2] [source eui64:8] [source endpoint:1] [clusterID:2] [destinationEUI64:8] [destEndpoint:1]
Sends an unbind request for a unicast binding to the target device.
target - INT16U - Target node ID
source eui64 - IEEE_ADDRESS - The source EUI64 of the binding (the remote device's EUI64)
source endpoint - INT8U - The source endpoint of the binding.
clusterID - INT16U - The cluster ID to unbind.
destinationEUI64 - IEEE_ADDRESS - The destination EUI64 in the binding (usually the local node's EUI64
destEndpoint - INT8U - The destination endpoint of the binding
7808 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ZDO_NODE_DESC_RSP_CONFIG#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ZDO_NODE_DESC_RSP_CONFIG
plugin test-harness z3 zdo zdo-node-desc-rsp-config [options:4]
Configure the next outgoing node descriptor response.
options - INT32U - The negative behavior options for this command.
7814 of file ./app/framework/test/headers/cli.docEMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ZDO_RESET#
#define EMBER_AF_DOXYGEN_CLI_COMMAND_PLUGIN_TEST_HARNESS_Z3_PLUGIN_TEST_HARNESS_Z3_ZDO_ZDO_RESET
plugin test-harness z3 zdo zdo-reset
Reset any pending negative ZDO behavior.
7819 of file ./app/framework/test/headers/cli.doc